LC5523F Single-Stage Power Factor Corrected Off-Line Switching Regulator IC Features and Benefits Description * Integrated on-width control circuit (it realizes high power factor by average current control) * Integrated soft-start circuit (reduces power stress during start-up on the incorporated power MOSFET and output rectifier) * Integrated bias assist circuit (improves the startup performance, suppresses VCC voltage droop during operation, allows reduction of VCC capacitor value as well as use of a ceramic capacitor) * Integrated Leading Edge Blanking (LEB) circuit * Integrated maximum on-time limit circuit * Protection features: Overcurrent protection (OCP): pulse-by-pulse Overvoltage protection (OVP): pins VCC, OVP, and OCP, auto restart Overload protection (OLP): auto restart Thermal shutdown (TSD): latched shutdown The LC5500 series is a power IC for LED drivers. It has an incorporated power MOSFET, and is designed for input capacitorless applications, making it possible for systems to comply with the harmonics standard (IEC61000-3-2 Class C). The controller adapts the average current control method for realizing high power factors, and the quasiresonant topology contributes to high efficiency and low EMI noise. The rich set of protection features helps to realize low component counts, and high performance-to-cost power supply. The LC5523F is intended for isolated designs. The incorporated MOSFET has a VDSS(min) rating of 650 V and RDS(on)(max) of 1.9 . It is capable of a maximum output power of 60 W on 230 VAC supply and 40 W on universal supply based on the thermal rating. Note that the maximum output power can be up to 120% to 140% of this value. However, it may be limited in applications with low output voltage or short duty cycle. Package: 7-pin TO-220F Not to scale LF 3052 LF 3051 LF 3054 Typical Application F1 VA C L1 D1 D2 D3 D4 C11 T1 L2 C1 C8 D8 R5 C2 C9 D9 U1 LC5523F D5 Vcc R1 R8 C10 R9 PC1 DZ1 D6 C17 LED R13 R11 C13 R17 DZ2 PC2 R6 Q1 R12 C4 Control Part R10 PC2 C12 U2 + C14 R14 R15 R18 C15 R19 R20 R16 C16 D/ST S/GND NC VCC OCP FB OVP 1 2 3 4 5 6 7 R7 C3 C5 ROCP LC5523F-DS R3 C6 PC1 R21 D7 C18 DZ3 R4 C7 SANKEN ELECTRIC CO., LTD. June 14, 2012 Single-Stage Power Factor Corrected Off-Line Switching Regulator IC LC5523F Selection Guide Part Number LC5523F Package TO-220F (specify leadform when ordering) The polarity value for current specifies a sink as "+," and a source as "-," referencing the IC. Absolute Maximum Ratings TA = 25C, unless otherwise specified Characteristic Drain Current1 Single Pulse Avalanche Energy2 Symbol IDPeak EAS Pins Rating Single pulse Notes 1-2 9.2 Unit A ILPeak = 2.9 A, VDD = 99 V, L = 20 mH 1-2 99 mJ Supply Voltage for Control Part VCC 4-2 35 V OCP Pin Voltage VOCP 5-2 -2.0 to 5.0 V FB Pin Voltage VFB 6-2 -0.3 to 7.0 V OVP Pin Voltage VOVP 7-2 -0.3 to 5.0 V Allowable Power Dissipation of MOSFET3 PD1 With infinite heatsink 1-2 20.2 W Without heatsink 1-2 1.8 W Internal Frame Temperature in Operation TF -20 to 115 C Operating Ambient Temperature TOP -55 to 115 C Storage Temperature Tstg -55 to 125 C Channel Temperature Tch 150 C 1Refer to MOSFET Safe Operating Area Curve. to MOSFET Avalanche Energy Derating Coefficient Curve. 3Refer to MOSFET Temperature versus Power Dissipation Curve. 2Refer LC5523F-DS SANKEN ELECTRIC CO., LTD. 2 June 14, 2012 Single-Stage Power Factor Corrected Off-Line Switching Regulator IC LC5523F ELECTRICAL CHARACTERISTICS (Controller Part) TA = 25C, VCC = 20 V, unless otherwise specified Characteristic Symbol Test Conditions Pins Min. Typ. Max. Unit Startup Operation Operation Start Voltage VCC(ON) 4-2 13.8 15.1 17.3 V Operation Stop Voltage* VCC(OFF) 4-2 8.4 9.4 10.7 V ICC(ON) 4-2 - - 3.7 mA VSTARTUP 1-2 42 57 72 V 4-2 -5.5 -3.0 -1.0 mA Operating Current Startup Circuit Operation Voltage Startup Current ICC(STARTUP) VCC = 13 V Startup Current Threshold Biasing Voltage-1* VCC(BIAS)1 4-2 9.5 11.0 12.5 V Startup Current Threshold Biasing Voltage-2 VCC(BIAS)2 4-2 14.4 16.6 18.8 V fOSC 1-2 11.0 14.0 18.0 kHz Maximum On-Width tON(MAX) 1-2 30.0 40.0 50.0 s FB Pin Voltage Minimum Limit VFB(MIN) 6-2 0.55 0.90 1.25 V Maximum Feedback Current IFB(MAX) 6-2 -40 -25 -10 A Leading Edge Blanking Time tON(LEB) 5-2 - 500 - ns Quasi-Resonant Operation Threshold Voltage-1 VBD(TH1) 5-2 0.14 0.24 0.34 V Quasi-Resonant Operation Threshold Voltage-2 VBD(TH2) 5-2 0.12 0.17 0.22 V OCP Pin Overcurrent Protection (OCP) Threshold Voltage VOCP 5-2 -0.66 -0.60 -0.54 V OCP Pin Source Current IOCP 5-2 -120 -40 -10 A OCP Pin Overvoltage Protection (OVP) Threshold Voltage VBD(OVP) 5-2 2.2 2.6 3.0 V Overload Protection (OLP) Threshold Voltage-1 VFB(OLP)1 6-2 5.0 5.5 6.0 V Overload Protection (OLP) Threshold Voltage-2 VFB(OLP)2 6-2 4.1 4.5 4.9 V OVP Pin OVP Threshold Voltage VOVP(OVP) 7-2 1.6 2.0 2.4 V VCC Pin OVP Threshold Voltage VCC(OVP) 4-2 28.5 31.5 34.0 V TJ(TSD) - 135 - - C Normal Operation PWM Operation Frequency Protection Operation Thermal Shutdown Activating Temperature *VCC(BIAS)1 > VCC(OFF) always. LC5523F-DS SANKEN ELECTRIC CO., LTD. 3 June 14, 2012 Single-Stage Power Factor Corrected Off-Line Switching Regulator IC LC5523F ELECTRICAL CHARACTERISTICS (MOSFET) TA = 25C, unless otherwise specified Characteristic Drain-to-Source Breakdown Voltage Drain Leakage Current On Resistance Switching Time Thermal Resistance LC5523F-DS Symbol Pins Min. Typ. Max. Unit VDSS Test Conditions 1-2 650 V IDSS 1-2 300 A RDS(on) 1-2 1.9 tf Rch-F Between channel and internal leadframe SANKEN ELECTRIC CO., LTD. 1-2 400 ns 3.1 C/W 4 June 14, 2012 Single-Stage Power Factor Corrected Off-Line Switching Regulator IC LC5523F Characteristic Performance MOSFET Safe Operating Area Curve 10 0.1 ms 100 Drain current limited by on-resistance 80 60 40 20 0 1 Drain Current, ID (A) Safe Operating Area Temperature Derating Coefficient (%) S. O. A. Temperature Derating Coefficient Curve 0 25 50 75 100 125 1 ms 0.1 150 To use this graph, apply the S.O.A temperature derating coefficient taken from the graph at the left Channel Temperature, Tch (C) 0.01 10 100 1000 Drain-to-Source Voltage, VDS (V) 100 MOSFET Temperature versus Power Dissipation Curve Allowable Power Dissipation, PD1 (W) EAS Temperature Derating Coefficient (%) MOSFET Avalanche Energy Derating Coefficient Curve 80 60 40 20 0 25 50 75 100 125 150 30 25 20.2 20 With infinite heatsink 15 10 5 0 25 Transient Thermal Resistance, Rch-c (C/W) Channel Temperature, Tch (C) 10 Without heatsink 1.8 0 50 75 100 115 125 150 Ambient Temperature, TA (C) Transient Thermal Resistance Curve 1 0.1 0.01 0.001 10-6 10-5 10-4 10-3 10-2 10-1 Time (s) LC5523F-DS SANKEN ELECTRIC CO., LTD. 5 June 14, 2012 Single-Stage Power Factor Corrected Off-Line Switching Regulator IC LC5523F Functional Block Diagram VCC Control Part D/ST STARTUP TSD UVLO Reg Drv Bias OVP OVP S/GND S RQ OCP Bottom Detection NC 3 OCP OLP OSC LEB Feedback Control FB Reg Pin-out Diagrams D/ST 1 LC5523F Pin List Table S/GND 2 NC 3 VCC 4 OCP FB (LF 3051) 5 6 OVP 7 D/ST 1 S/GND 2 NC VCC 3 OCP FB OVP LC5523F-DS (LF 3052) 4 Number Name Function 1 D/ST MOSFET drain pin and input of the startup current 2 S/GND MOSFET source and GND pin for the Control Part 3 NC 4 VCC No connection Supply voltage input and Overvoltage protection (OVP) signal input 5 OCP Overcurrent Protection, quasi-resonant signal input pin, and Overvoltage Protection (OVP) signal input 6 FB 7 OVP Feedback signal input and Overload Protection (OLP) signal input Overvoltage Protection (OVP) signal input 5 6 7 1 D/ST 2 S/GND 3 NC 4 VCC 5 OCP 6 FB 7 OVP (LF 3054) SANKEN ELECTRIC CO., LTD. 6 June 14, 2012 Single-Stage Power Factor Corrected Off-Line Switching Regulator IC LC5523F Package Outline Drawing, TO-220F Leadform 3051 2.6 0.2 15 0.3 5.6 Gate burr O3.2 0.2 4.2 0.2 2.8 +0.2 10 0.2 LC 1.1 a 2.6 0.1 At base of pin 10.4 0.5 7-0.62 0.15 +0.2 7-0.55 -0.1 R-end R-end +0.2 0.45 -0.1 5xP1.170.15 5.850.15 2 0.15 50.5 50.5 b At base of pin 5.080.6 2.540.6 At tip of pin At tip of pin 2 1 4 3 6 5 7 0.5 0.5 Front view Unit: mm Package: TO-220F-7L Leadframe material: Cu Pin treatment: Solder dip Weight: Approximately 1.45 g "Gate Burr" shows area where 0.3 mm (max) gate burr may be present 0.5 0.5 Side view a: Part # 5523F b: Lot number st 1 letter: Last digit of year nd 2 letter: Month Jan to September: Numeric October: O November: N December: D rd th 3 and 4 letter: Date 01 to 31: Numeric th 5 letter: Internal use control number Pin treatment Pb-free. Device composition compliant with the RoHS directive. LC5523F-DS SANKEN ELECTRIC CO., LTD. 7 June 14, 2012 Single-Stage Power Factor Corrected Off-Line Switching Regulator IC LC5523F Package Outline Drawing, TO-220F Leadform 3052 2.6 0.2 LC 15 0.3 5.6 Gate burr O3.2 0.2 4.2 0.2 2.8 +0.2 10 0.2 a 1.1 2.6 0.1 At base of pin 50.5 b 10.4 0.5 7-0.62 0.15 +0.2 7-0.55 -0.1 0.45 +0.2 -0.1 5xP1.170.15 5.850.15 2 0.15 R-end 5.080.6 At base of pin At tip of pin 0.5 0.5 Front View 1 0.5 Side View 2 3 4 5 6 7 Unit: mm Package: TO-220F-7L Leadframe material: Cu Pin treatment: Solder dip Weight: Approximately 1.45 g "Gate Burr" shows area where 0.3 mm (max) gate burr may be present Pin treatment Pb-free. Device composition compliant with the RoHS directive. LC5523F-DS 0.5 a: Part # 5523F b: Lot number st 1 letter: Last digit of year nd 2 letter: Month Jan to September: Numeric October: O November: N December: D rd th 3 and 4 letter: Date 01 to 31: Numeric th 5 letter: Internal use control number SANKEN ELECTRIC CO., LTD. 8 June 14, 2012 Single-Stage Power Factor Corrected Off-Line Switching Regulator IC LC5523F 2.8 0.2 Package Outline Drawing, TO-220F Leadform 3054 2.6 0.2 a b 2.8 0.5 At tip of pin 2.5 0.5 LC 15 0.3 (5.6) Gate burr 4.20.2 O3.2 0.2 10 0.2 (1.1) 3-( R1) 2.6 0.1 At base of pin At base of pin 0.5 At tip of pin 5xP 1.17 0.15 = 5.85 0.15 2 0.15 +0.2 0.45 -0.1 7-0.55 +0.2 -0.1 5 0.5 7-0.62 0.15 3.80.5 0.5 Plan View 1 0.5 0.5 Side View 2 3 4 5 6 7 Unit: mm Package: TO-220F-7L Leadframe material: Cu Pin treatment: Solder dip Weight: Approximately 1.45 g "Gate Burr" shows area where 0.3 mm (max) gate burr may be present a: Part # 5523F b: Lot number st 1 letter: Last digit of year nd 2 letter: Month Jan to September: Numeric October: O November: N December: D rd th 3 and 4 letter: Date 01 to 31: Numeric th 5 letter: Internal use control number Pin treatment Pb-free. Device composition compliant with the RoHS directive. LC5523F-DS SANKEN ELECTRIC CO., LTD. 9 June 14, 2012 Single-Stage Power Factor Corrected Off-Line Switching Regulator IC LC5523F Because reliability can be affected adversely by improper storage environments and handling methods, please observe the following cautions. Cautions for Storage * Ensure that storage conditions comply with the standard temperature (5C to 35C) and the standard relative humidity (around 40% to 75%); avoid storage locations that experience extreme changes in temperature or humidity. * Avoid locations where dust or harmful gases are present and avoid direct sunlight. * Reinspect for rust on leads and solderability of the products that have been stored for a long time. Cautions for Testing and Handling When tests are carried out during inspection testing and other standard test periods, protect the products from power surges from the testing device, shorts between the product pins, and wrong connections. Ensure all test parameters are within the ratings specified by Sanken for the products. Remarks About Using Silicone Grease with a Heatsink * When silicone grease is used in mounting the products on a heatsink, it shall be applied evenly and thinly. If more silicone grease than required is applied, it may produce excess stress. * Volatile-type silicone greases may crack after long periods of time, resulting in reduced heat radiation effect. Silicone greases with low consistency (hard grease) may cause cracks in the mold resin when screwing the products to a heatsink. Our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the product life, are indicated below: Type Suppliers G746 Shin-Etsu Chemical Co., Ltd. YG6260 Momentive Performance Materials Inc. SC102 Dow Corning Toray Co., Ltd. Cautions for Mounting to a Heatsink * When the flatness around the screw hole is insufficient, such as when mounting the products to a heatsink that has an extruded (burred) screw hole, the products can be damaged, even with a lower than LC5523F-DS recommended screw torque. For mounting the products, the mounting surface flatness should be 0.05 mm or less. * Please select suitable screws for the product shape. Do not use a flat-head machine screw because of the stress to the products. Self-tapping screws are not recommended. When using self-tapping screws, the screw may enter the hole diagonally, not vertically, depending on the conditions of hole before threading or the work situation. That may stress the products and may cause failures. * Recommended screw torque: 0.588 to 0.785 Nm (6 to 8 kgfcm). * For tightening screws, if a tightening tool (such as a driver) hits the products, the package may crack, and internal stress fractures may occur, which shorten the lifetime of the electrical elements and can cause catastrophic failure. Tightening with an air driver makes a substantial impact. In addition, a screw torque higher than the set torque can be applied and the package may be damaged. Therefore, an electric driver is recommended. When the package is tightened at two or more places, first pre-tighten with a lower torque at all places, then tighten with the specified torque. When using a power driver, torque control is mandatory. Soldering * When soldering the products, please be sure to minimize the working time, within the following limits: 2605C 101 s (Flow, 2 times) 38010C 3.50.5 s (Soldering iron, 1 time) * Soldering should be at a distance of at least 2.0 mm from the body of the products. Electrostatic Discharge * When handling the products, the operator must be grounded. Grounded wrist straps worn should have at least 1 M of resistance from the operator to ground to prevent shock hazard, and it should be placed near the operator. * Workbenches where the products are handled should be grounded and be provided with conductive table and floor mats. * When using measuring equipment such as a curve tracer, the equipment should be grounded. * When soldering the products, the head of soldering irons or the solder bath must be grounded in order to prevent leak voltages generated by them from being applied to the products. * The products should always be stored and transported in Sanken shipping containers or conductive containers, or be wrapped in aluminum foil. SANKEN ELECTRIC CO., LTD. 10 June 14, 2012 LC5523F Single-Stage Power Factor Corrected Off-Line Switching Regulator IC * The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this is the latest revision of the document before use. * Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of Sanken or any third party which may result from its use. * Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. * Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest Sanken sales representative to discuss, prior to the use of the products herein. The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. * In the case that you use Sanken products or design your products by using Sanken products, the reliability largely depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. For these stresses, instantaneous values, maximum values and minimum values must be taken into consideration. In addition, it should be noted that since power devices or IC's including power devices have large self-heating value, the degree of derating of junction temperature affects the reliability significantly. * When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. * Anti radioactive ray design is not considered for the products listed herein. * Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken's distribution network. * The contents in this document must not be transcribed or copied without Sanken's written consent. LC5523F-DS SANKEN ELECTRIC CO., LTD. 11 June 14, 2012