E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film QPL MIL-PRF-55342 Qualified Thin Film Resistor, Surface Mount Chip FEATURES * Established reliability, "R" failure rate level (100 ppm), C = 2 * High purity alumina substrate 99.6 % purity * Wraparound termination featuring a tenacious adhesion layer covered with an electroplated nickel barrier layer for + 150 C operating conditions * Very low noise and voltage coefficient (< - 25 dB, 0.5 ppm/V) * Non-inductive * Laser-trimmed tolerances 0.1 % * Wraparound resistance less than 0.010 typical * In-lot tracking less than 5 ppm/C * Complete MIL-testing available in-house * Antistatic waffle pack or tape and reel packaging available * Military/aerospace/QPL Actual Size M55342/02 Thin Film Mil chip resistors feature all sputtered wraparound termination for excellent adhesion and dimensional uniformity. They are ideal in applications requiring stringent performance requirements. Established reliability is assured through 100 % screening and extensive environmental lot testing. Wafer is sawed producing exact dimensions and clean, straight edges. Note * Specification changed by D.S.C.C. from MIL-R-55342 to MIL-PRF-55342 Note ** Please see document "Vishay Material Category Policy": www.vishay.com/doc?99902 CONSTRUCTION Passivation Resistor Film Solder Coating TYPICAL PERFORMANCE ABSOLUTE Nickel Barrier High Purity Alumina Substrate Adhesion Layer TCR 25 TOL. 0.1 STANDARD ELECTRICAL SPECIFICATIONS TEST Material Resistance Range TCR: Absolute Tolerance: Absolute Stability: Absolute Stability: Ratio Voltage Coefficient Working Voltage Operating Temperature Range Storage Temperature Range Noise Shelf Life Stability: Absolute SPECIFICATIONS Passivated nichrome 10 to 6.19 M 25 ppm/C to 300 ppm/C 0.1 % to 10 % R 0.02 % 0.1 ppm/V 30 V to 200 V - 55 C to + 125 C - 55 C to + 150 C < - 25 dB R 0.01 % CONDITIONS - 55 C to + 125 C + 25 C 2000 h at + 70 C 1 year at + 25 C COMPONENT RATINGS CASE SIZE POWER RATING (mW) 50 125 200 150 225 150 250 800 1000 500 50 100 WORKING VOLTAGE (V) RESISTANCE RANGE () BY CHARACTERISTICS TOLERANCE E E H, K, M H, K, M (0.1 %) (1 %, 2 %, 5 %) (0.1 %) (1 %, 2 %, 5 %) 49.9 to 150K 49.9 to 150K 20 to 150K 20 to 150K 49.9 to 301K 49.9 to 301K 20 to 301K 20 to 301K 49.9 to 649K 49.9 to 649K 10 to 649K 10 to 649K 49.9 to 1.69M 49.9 to 1.69M 10 to 1.69M 10 to 1.69M 49.9 to 3.16M 49.9 to 3.16M 10 to 3.16M 10 to 3.16M 49.9 to 475K 49.9 to 475K 10 to 475K 10 to 475K 49.9 to 1.5M 49.9 to 1.5M 10 to 1.5M 10 to 1.5M 49.9 to 4.02M 49.9 to 4.02M 10 to 4.02M 10 to 4.02M 49.9 to 6.19M 49.9 to 6.19M 10 to 6.19M 10 to 6.19M 49.9 to 1M 49.9 to 1M 49.9 to 1M 49.9 to 1M 49.9 to 100K 49.9 to 100K 20 to 100K 20 to 100K 49.9 to 258K 49.9 to 261K 10 to 258K 10 to 261K M55342/01 40 M55342/02 40 M55342/03 75 M55342/04 125 M55342/05 175 M55342/06 50 D55342/07 100 M55342/08 150 M55342/09 200 M55342/10 75 M55342/11 30 M55342/12 50 Note * Values listed are a guide, refer to MIL spec for value/tolerance allowance Revision: 08-Jun-11 1 Document Number: 60018 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film DIMENSIONS in inches D W T E L CASE SIZE TERM. L W T D E M55342/01 B 0.055 0.006 0.025 0.005 0.010 to 0.030 0.010 0.005 0.015 0.005 M55342/02 B 0.055 0.006 0.050 0.005 0.012 to 0.033 0.010 0.005 0.015 0.005 M55342/03 B 0.105 0.007 0.050 0.005 0.015 to 0.033 0.015 0.005 0.015 0.005 M55342/04 B 0.155 0.007 0.050 0.005 0.015 to 0.033 0.015 0.005 0.015 0.005 M55342/05 B 0.230 0.007 0.075 0.005 0.015 to 0.033 0.020 0.005 0.020 0.005 M55342/06 B 0.080 0.006 0.050 0.005 0.015 to 0.033 0.016 0.008 0.015 0.005 D55342/07 B 0.126 0.008 0.063 0.005 0.015 to 0.033 M55342/08 B 0.209 + 0.009/- 0.018 0.098 0.005 0.015 to 0.033 M55342/09 B 0.259 + 0.009/- 0.015 0.124 0.005 0.015 to 0.033 0.020 0.005 0.020 0.005 M55342/10 B 0.105 0.007 0.100 0.005 0.015 to 0.033 0.015 0.005 0.015 0.005 M55342/11 B 0.040 0.005 0.025 0.005 0.010 to 0.030 0.010 0.005 0.015 0.005 M55342/12 B 0.064 0.006 0.032 0.005 0.010 to 0.033 0.012 0.005 0.015 0.005 0.020 + 0.005/- 0.010 0.020 + 0.005/- 0.010 0.020 0.005 0.020 0.005 ENVIRONMENTAL TESTS MIL-PRF-55342 LIMITS (R ) VISHAY PERFORMANCE (R ) Thermal Shock 0.1 % 0.020 % Low Temperature Operation 0.1 % 0.025 % Short Time Overload 0.1 % 0.050 % High Temperature Exposure 0.1 % 0.009 % Resistance to Bonding 0.2 % 0.006 % Moisture Resistance 0.2 % 0.004 % 25 ppm/C < 15 ppm/C Life (2000 h at + 70 C) 0.5 % 0.02 % Life (10 000 h at + 70 C) 2.0 % 0.04 % ENVIRONMENTAL TEST TCR MECHANICAL SPECIFICATIONS Resistive Element Passivated nichrome Substrate Material Alumina Chip Terminations Solder over nickel Fused Solder Revision: 08-Jun-11 FSCM CAGE # - 57489 SN 63 2 Document Number: 60018 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film GLOBAL PART NUMBER INFORMATION New Global Part Numbering: M55342E06B1C00RTS M 5 5 3 GLOBAL TCR MODEL CHARACTERISTIC M55342 or D55342 (/07 size only) E = 25 ppm/C H = 50 ppm/C K = 100 ppm/C M = 300 ppm/C 4 2 E 0 6 B 1 C CASE SIZE TERMINATION OHMIC VALUE 01 = 0502 02 = 0505 03 = 1005 04 = 1505 05 = 2208 06 = 0705 07 = 1206 08 = 2010 09 = 2512 10 = 1010 11 = 0402 12 = 0603 B = Solderable Three digits and a letter. Letter identifies tolerance, acts as multiplier and decimal locator. Tolerance 0.1 % 1% 0 0 FAILURE RATE G H 5% J K T L 10 % M N P T PACKAGING M = 1.0 % per 1000 h P = 0.1 % per 1000 h MULTIPLIER R = 0.01 % 1 1 k 1 M per 1000 h A B C C = Non ER version D E F 2% R S V THIN FILM CODE (1) Standard Packaging: V BS = BULK for K and M 100 min., 1 mult TCR WS =WAFFLE W/tolerance 100 min., 1 mult TAPE AND REEL 1% T0 = 100 min., 100 mult T1 = 1000 min., 1000 mult T3 = 300 min., 300 mult T5 = 500 min., 500 mult TF = Full reel ( 2K, 4K, or 5K dependent on case size ) per tape and reel document 60034 TS = 100 min., 1 mult Special Packaging: WAFFLE WI = 100 min., 1 mult (item single lot date code) WP =100 min., 1 mult (package unit single lot date code) TAPE AND REEL TI = 100 min., 1 mult (item single lot date code) TP = 100 min., 1 mult (package unit single lot date code) Historical Part Number example: M55342K06B5E60R (for reference purposes only) M55342 K 06 B 5E60 R SERIES TCR CHARACTERISTIC CASE SIZE TERMINATION VALUE AND TOLERANCE FAILURE RATE Note (1) Only add a V at the end of part number to specify Vishay Dale Thin Film for K/M TCR and tolerance 1 % and higher Revision: 08-Jun-11 3 Document Number: 60018 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1