5SGXMA5K3F35C2LN - Altera Corporation

Stratix V Device Overview

2015.10.01

SV51001 Subscribe Send Feedback

Altera’s 28-nm Stratix® V FPGAs include innovations such as an enhanced core architecture, integrated

transceivers up to 28.05 gigabits per second (Gbps), and a unique array of integrated hard intellectual

property (IP) blocks.

With these innovations, Stratix V FPGAs deliver a new class of application-targeted devices optimized for:

• Bandwidth-centric applications and protocols, including PCI Express® (PCIe®) Gen3

• Data-intensive applications for 40G/100G and beyond

• High-performance, high-precision digital signal processing (DSP) applications

Stratix V devices are available in four variants (GT, GX, GS, and E), each targeted for a different set of

applications. For higher volume production, you can prototype with Stratix V FPGAs and use the low-

risk, low-cost path to HardCopy® V ASICs.

Related Information

Stratix V Device Handbook: Known Issues

Lists the planned updates to the Stratix V Device Handbook chapters.

Stratix V Family Variants

The Stratix V device family contains the GT, GX, GS, and E variants.

Stratix V GT devices, with both 28.05-Gbps and 12.5-Gbps transceivers, are optimized for applications

that require ultra-high bandwidth and performance in areas such as 40G/100G/400G optical communica‐

tions systems and optical test systems. 28.05-Gbps and 12.5-Gbps transceivers are also known as GT and

GX channels, respectively.

Stratix V GX devices offer up to 66 integrated transceivers with 14.1-Gbps data rate capability. These

transceivers also support backplane and optical interface applications. These devices are optimized for

high-performance, high-bandwidth applications such as 40G/100G optical transport, packet processing,

and traffic management found in wireline, military communications, and network test equipment

markets.

Stratix V GS devices have an abundance of variable precision DSP blocks, supporting up to 3,926 18x18

or 1,963 27x27 multipliers. In addition, Stratix V GS devices offer integrated transceivers with 14.1-Gbps

data rate capability. These transceivers also support backplane and optical interface applications. These

devices are optimized for transceiver-based DSP-centric applications found in wireline, military,

broadcast, and high-performance computing markets.

trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as

trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance

of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any

products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information,

product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device

specifications before relying on any published information and before placing orders for products or services.

ISO

9001:2008

Registered

www.altera.com

101 Innovation Drive, San Jose, CA 95134

Stratix V E devices offer the highest logic density within the Stratix V family with nearly one million logic

elements (LEs) in the largest device. These devices are optimized for applications such as ASIC and system

emulation, diagnostic imaging, and instrumentation.

Common to all Stratix V family variants are a rich set of high-performance building blocks, including a

redesigned adaptive logic module (ALM), 20 Kbit (M20K) embedded memory blocks, variable precision

DSP blocks, and fractional phase-locked loops (PLLs). All of these building blocks are interconnected by

Altera’s superior multi-track routing architecture and comprehensive fabric clocking network.

Also common to Stratix V devices is the new Embedded HardCopy Block, which is a customizable hard

IP block that leverages Altera’s unique HardCopy ASIC capabilities. The Embedded HardCopy Block in

Stratix V FPGAs is used to harden IP instantiation of PCIe Gen3, Gen2, and Gen1.

Stratix V Features Summary

Table 1: Summary of Features for Stratix V Devices

Feature Description

Technology • 28-nm TSMC process technology

• 0.85-V or 0.9-V core voltage

Low-power serial

transceivers • 28.05-Gbps transceivers on Stratix V GT devices

• Electronic dispersion compensation (EDC) for XFP, SFP+, QSFP, CFP

optical module support

• Adaptive linear and decision feedback equalization

• Transmitter pre-emphasis and de-emphasis

• Dynamic reconfiguration of individual channels

• On-chip instrumentation (EyeQ non-intrusive data eye monitoring)

Backplane capability • 600-Megabits per second (Mbps) to 12.5-Gbps data rate capability

General-purpose I/Os

(GPIOs) • 1.6-Gbps LVDS

• 1,066-MHz external memory interface

• On-chip termination (OCT)

• 1.2-V to 3.3-V interfacing for all Stratix V devices

Embedded HardCopy

Block • PCIe Gen3, Gen2, and Gen1 complete protocol stack, x1/x2/x4/x8 end

point and root port

Embedded transceiver

hard IP • Interlaken physical coding sublayer (PCS)

• Gigabit Ethernet (GbE) and XAUI PCS

• 10G Ethernet PCS

• Serial RapidIO® (SRIO) PCS

• Common Public Radio Interface (CPRI) PCS

• Gigabit Passive Optical Networking (GPON) PCS

Power management • Programmable Power Technology

• Quartus II integrated PowerPlay Power Analysis

2Stratix V Features Summary SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Feature Description

High-performance core

fabric • Enhanced ALM with four registers

• Improved routing architecture reduces congestion and improves compile

times

Embedded memory

blocks • M20K: 20-Kbit with hard error correction code (ECC)

• MLAB: 640-bit

Variable precision DSP

blocks • Up to 600 MHz performance

• Natively support signal processing with precision ranging from 9x9 up to

54x54

• New native 27x27 multiply mode

• 64-bit accumulator and cascade for systolic finite impulse responses (FIRs)

• Embedded internal coefficient memory

• Pre-adder/subtractor improves efficiency

• Increased number of outputs allows more independent multipliers

Fractional PLLs • Fractional mode with third-order delta-sigma modulation

• Integer mode

• Precision clock synthesis, clock delay compensation, and zero delay buffer

(ZDB)

Clock networks • 800-MHz fabric clocking

• Global, quadrant, and peripheral clock networks

• Unused clock networks can be powered down to reduce dynamic power

Device configuration • Serial and parallel flash interface

• Enhanced advanced encryption standard (AES) design security features

• Tamper protection

• Partial and dynamic reconfiguration

• Configuration via Protocol (CvP)

High-performance

packaging • Multiple device densities with identical package footprints enables

seamless migration between different FPGA densities

• FBGA packaging with on-package decoupling capacitors

• Lead and RoHS-compliant lead-free options

HardCopy V migration —

Stratix V Family Plan

The following tables list the features of the different Stratix V devices.

The information in this section is correct at the time of publication. For the latest information and to get

more details, refer to the Altera Product Selector.

SV51001

2015.10.01 Stratix V Family Plan 3

Stratix V Device Overview Altera Corporation

Send Feedback

Table 2: Stratix V GT Device Features

Feature 5SGTC5 5SGTC7

Logic Elements (K) 425 622

ALMs 160,400 234,720

Registers (K) 642 939

28.05/12.5-Gbps Transceivers 4/32 4/32

PCIe hard IP Blocks 1 1

Fractional PLLs 28 28

M20K Memory Blocks 2,304 2,560

M20K Memory (MBits) 45 50

Variable Precision Multipliers (18x18) 512 512

Variable Precision Multipliers (27x27) 256 256

DDR3 SDRAM x72 DIMM Interfaces 4 4

User I/Os(1), Full-Duplex LVDS, 28.05/12.5-Gbps Transceivers

Package (2) (3) 5SGTC5 5SGTC7

KF40-F1517 (4)

(40 mm)

600, 150, 36 600, 150, 36

(1) The number of GPIOs does not include transceiver I/Os. In the Quartus II software, the number of user I/

Os includes transceiver I/Os.

(2) Packages are flipchip ball grid array (1.0-mm pitch).

(3) Each package row offers pin migration (common board footprint) for all devices in the row.

(4) Migration between select Stratix V GT devices and Stratix V GX devices is available. For more information,

refer to Table 6 and to AN 644: Migration Between Stratix V GX and Stratix V GT Devices.

4Stratix V Family Plan SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Table 3: Stratix V GX Device Features

Features 5SGXA

35SGXA

45SGXA

55SGXA

75SGXA

95SGXA

B5SGXB

55SGXB

65SGXB

95SGXBB

Logic

Elements

(K)

340 420 490 622 840 952 490 597 840 952

ALMs 128,300 158,500 185,000 234,720 317,000 359,200 185,000 225,400 317,000 359,200

Registers

(K) 513 634 740 939 1,268 1,437 740 902 1,268 1,437

14.1-Gbps

Transceive

12, 24,

or 36 24 or

36 24, 36,

or 48 24, 36,

or 48 36 or

48 36 or

48 66 66 66 66

PCIe hard

IP Blocks 1 or 2 1 or 2 1, 2, or

41, 2, or

41 or 4 1 or 4 1 or 4 1 or 4

Fractional

PLLs 20 (5) 24 28 28 28 28 24 24 32 32

M20K

Memory

Blocks

957 1,900 2,304 2,560 2,640 2,640 2,100 2,660 2,640 2,640

M20K

Memory

(MBits)

19 37 45 50 52 52 41 52 52 52

Variable

Precision

Multipliers

(18x18)

512 512 512 512 704 704 798 798 704 704

Variable

Precision

Multipliers

(27x27)

256 256 256 256 352 352 399 399 352 352

(5) The F1517 package contains 24 PLLs. The other packages with this device contain 20 PLLs.

SV51001

2015.10.01 Stratix V Family Plan 5

Stratix V Device Overview Altera Corporation

Send Feedback

Features 5SGXA

35SGXA

45SGXA

55SGXA

75SGXA

95SGXA

B5SGXB

55SGXB

65SGXB

95SGXBB

DDR3

SDRAM

x72 DIMM

Interfaces

(6)

666666444 4

User I/Os(1), Full-Duplex LVDS, 14.1-Gbps Transceivers

Package (2) (3)

(7) (8) 5SGXA3 5SGXA4 5SGXA5 5SGXA7 5SGXA9 5SGXA

B5SGXB5 5SGXB6 5SGXB9 5SGXBB

EH29-

H780

(33 mm)

360, 90,

12H———————— —

HF35-

F1152 (9)

(35 mm)

432,

108, 24 552,

138, 24 552,

138, 24 ————— —

KF35-

F1152

(35 mm)

432,

108, 36 432,

108, 36 ————— —

KF40-

F1517

(40 mm)

KH40-

H1517 (9)

(45 mm)

696,

174, 36 696,

174,

36H

696,

174,

36H

— — — —

(6) These are the maximum number of x72 interfaces available. The actual number of interfaces depends on the

device package.

(7) LVDS counts are full duplex channels. Each full duplex channel is one transmitter (TX) pair plus one

receiver (RX) pair.

(8) A superscript H after the number of transceivers indicates that this device is only available in a hybrid

package. Hybrid packages are slightly larger than conventional FBGAs. Refer to Altera’s packaging

documentation for more information.

(9) Migration between select Stratix V GX devices and Stratix V GS devices is available. For more information,

refer to Table 6.

6Stratix V Family Plan SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

User I/Os(1), Full-Duplex LVDS, 14.1-Gbps Transceivers

Package (2) (3)

(7) (8) 5SGXA3 5SGXA4 5SGXA5 5SGXA7 5SGXA9 5SGXA

B5SGXB5 5SGXB6 5SGXB9 5SGXBB

NF40-

F1517 (4)

(40 mm)

— — 600,

150, 48 600,

150, 48 ————— —

RF40-

F1517

(40 mm)

— — — — — — 432,

108, 66 432,

108, 66 — —

RF43-

F1760

(42.5

mm)

— — — — — — 600,

150, 66 600,

150, 66 — —

RH43-

H1760

(45 mm)

— — — — — — — — 600,

150,

66H

600, 150, 66H

NF45-

F1932 (9)

(45 mm)

— — 840,

210, 48 840,

210, 48 — — — —

Table 4: Stratix V GS Device Features

Features 5SGSD3 5SGSD4 5SGSD5 5SGSD6 5SGSD8

Logic Elements (K) 236 360 457 583 695

ALMs 89,000 135,840 172,600 220,000 262,400

Registers (K) 356 543 690 880 1,050

14.1-Gbps

transceivers 12 or 24 12, 24, or 36 24 or 36 36 or 48 36 or 48

PCIe hard IP

blocks 1 1 1 1, 2, or 4 1, 2, or 4

Fractional PLLs 20 20 (5) 24 28 28

M20K Memory

Blocks 688 957 2,014 2,320 2,567

SV51001

2015.10.01 Stratix V Family Plan 7

Stratix V Device Overview Altera Corporation

Send Feedback

Features 5SGSD3 5SGSD4 5SGSD5 5SGSD6 5SGSD8

M20K Memory

(MBits) 13 19 39 45 50

Variable Precision

Multipliers (18x18) 1,200 2,088 3,180 3,550 3,926

Variable Precision

Multipliers (27x27) 600 1,044 1,590 1,775 1,963

DDR3 SDRAM x72

DIMM Interfaces 2446 6

User I/Os(1), Full-Duplex LVDS, 14.1-Gbps Transceivers

Package (2) (3) (7) (8) 5SGSD3 5SGSD4 5SGSD5 5SGSD6 5SGSD8

EH29-H780

(33 mm)

360, 90, 12H360, 90, 12H— — —

HF35-F1152 (9)

(35 mm)

432, 108, 24 432, 108, 24 552, 138, 24 — —

KF40-F1517 (9)

(40 mm)

— 696, 174, 36 696, 174, 36 696, 174, 36 696, 174, 36

NF45-F1932 (9)

(45 mm)

— — — 840, 210, 48 840, 210, 48

Table 5: Stratix V E Device Features

Features 5SEE9 5SEEB

Logic Elements (K) 840 952

ALMs 317,000 359,200

Registers (K) 1,268 1,437

Fractional PLLs 28 28

M20K Memory Blocks 2,640 2,640

M20K Memory (MBits) 52 52

Variable Precision Multipliers (18x18) 704 704

8Stratix V Family Plan SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Features 5SEE9 5SEEB

Variable Precision Multipliers (27x27) 352 352

DDR3 SDRAM x72 DIMM Interfaces 6 6

User I/Os(1), Full-Duplex LVDS

Package (2) (3) (7) (8) 5SEE9 5SEEB

H40-H1517

(45 mm)

696, 174H696, 174H

F45-F1932

(45 mm)

840, 210 840, 210

Table 6: Device Migration List Across All Stratix V Device Variants

All devices in a specific column allow migration.

Package

EH29-

H780 HF35-

F1152 (

10)

KF35-

F1152 KF40-

F1517/

KH40-

H1517

(11)

NF40/

KF40-

F1517 (1

2) (13)

RF40-

F1517 H40-

H1517 RF43-

F1760 NF45-

F1932 (

11)

F45-

F1932 RH43-

H1760

Stratix V GX devices

A3 Yes Yes Yes Yes

A4 Yes Yes Yes

A5 Yes Yes Yes Yes Yes

A7 Yes Yes Yes Yes Yes

A9 Yes Yes

AB Yes Yes

(10) All devices in this column are in the HF35 package and have twenty-four 14.1-Gbps transceivers.

(11) Different devices within this column have small differences in the overall package height. When multiple

Stratix V devices with different package heights are placed on a single board, a single-piece heatsink may not

cover the devices evenly. Refer to AN 670: Thermal Solutions to Address Height Variation in Stratix V

Packages.

(12) The 5SGTC5/7 devices in the KF40 package have four 28.05-Gbps transceivers and thirty-two 12.5-Gbps

transceivers. Other devices in this column are in the NF40 package and have forty-eight 14.1-Gbps

transceivers.

(13) For more information, refer to AN 644: Migration Between Stratix V GX and Stratix V GT Devices.

SV51001

2015.10.01 Stratix V Family Plan 9

Stratix V Device Overview Altera Corporation

Send Feedback

Package

B5 Yes Yes

B6 Yes Yes

B9 Yes

BB Yes

Stratix V GT devices

C5 Yes

C7 Yes

Stratix V GS devices

D3 Yes Yes

D4 Yes Yes Yes

D5 Yes Yes

D6 Yes Yes

D8 Yes Yes

Stratix V E devices

E9 Yes Yes

EB Yes Yes

Note: To verify the pin migration compatibility, use the Pin Migration View window in the Quartus II

software Pin Planner.

Related Information

•Altera Product Selector

Provides the latest information about Altera products.

•For more information about verifying the pin migration compatibility, refer to the I/O

Management chapter in volume 2 of the Quartus II Handbook.

•For full package details, refer to the Package information datasheet for Altera devices.

•AN 644: Migration Between Stratix V GX and Stratix V GT Devices

•AN 670: Thermal Solutions to Address Height Variation in Stratix V Packages

Low-Power Serial Transceivers

Stratix V FPGAs deliver the industry’s most flexible transceivers with the highest bandwidth from

600 Mbps to 28.05 Gbps, low bit error ratio (BER), and low power. Stratix V transceivers have many

enhancements to improve flexibility and robustness. These enhancements include robust analog receiver

clock and data recovery (CDR), advanced pre-emphasis, and equalization. In addition, each channel

provides full featured embedded PCS hard IP to simplify the design, lower the power, and save valuable

core resources.

Stratix V transceivers are compliant with a wide range of standard protocols and data rates and are

equipped with a variety of signal conditioning features to support backplane, optical module, and chip-to-

chip applications.

10 Low-Power Serial Transceivers SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Stratix V transceivers are located on the left and right sides of the device, as shown in the figure below.

The transceivers are isolated from the rest of the chip to prevent core and I/O noise from coupling into

the transceivers, thereby ensuring optimal signal integrity. The transceiver channels consist of the physical

medium attachment (PMA), PCS, and high-speed clock networks. You can also configure unused

transceiver PMA channels as additional transmitter PLLs.

Figure 1: Stratix V GT, GX, and GS Device Chip View

This figure represents one variant of a Stratix V device with transceivers. Other variants may have a

different floorplan than the one shown here.

PCS

PMA

(1)

Clock Networks

M20K Blocks

DSP Blocks

M20K Blocks

DSP Blocks

M20K Blocks

DSP Blocks

Core Logic

Fabric Core Logic

Fabric

PMA

Per Channel: Standard PCS, 10G PCS, PCIe Gen3 PCS

PMA

Per Channel: Standard PCS, 10G PCS, PCIe Gen3 PCS

Embedded HardCopy BlockEmbedded HardCopy Block

Embedded HardCopy Block Embedded HardCopy Block

I/O, LVDS, and Memory Interface

Fractional PLLs

Note:

(1)

You can use the unused transceiver channels as additional transceiver transmitter PLLs.

The following table lists the PMA features for the Stratix V transceivers.

Table 7: Transceiver PMA Features

Feature Capability

Chip-to-chip support 28.05 Gbps and 12.5 Gbps (Stratix V GT devices) and

14.1 Gbps (Stratix V GX and GS devices)

SV51001

2015.10.01 Low-Power Serial Transceivers 11

Stratix V Device Overview Altera Corporation

Send Feedback

Feature Capability

Backplane support 12.5 Gbps (Stratix V GX, GS, and GT devices)

Cable driving support PCIe cable and eSATA applications

Optical module support with EDC 10G Form-factor Pluggable (XFP), Small Form-factor

Pluggable (SFP+), Quad Small Form-factor Pluggable (QSFP),

CXP, 100G Pluggable (CFP), 100G Form-factor Pluggable

Continuous Time Linear Equalization

(CTLE) Receiver 4-stage linear equalization to support high-attenua‐

tion channels

Decision Feedback Equalization (DFE) Receiver 5-tap digital equalizer to minimize losses and crosstalk

Adaptive equalization (AEQ) Adaptive engine to automatically adjust equalization to

compensate for changes over time

PLL-based clock recovery Superior jitter tolerance versus phase interpolation techniques

Programmable deserialization and word

alignment Flexible deserialization width and configurable word alignment

patterns

Transmitter equalization (pre-emphasis) Transmitter driver 4-tap pre-emphasis and de-emphasis for

protocol compliance under lossy conditions

Ring and LC oscillator transmitter PLLs Choice of transmitter PLLs per channel, optimized for specific

protocols and applications

On-chip instrumentation (EyeQ data-

eye monitor) Allows non-intrusive on-chip monitoring of both width and

height of the data eye

Dynamic reconfiguration Allows reconfiguration of single channels without affecting

operation of other channels

Protocol support Compliance with over 50 industry standard protocols in the

range of 600 Mbps to 28.05 Gbps

The Stratix V core logic connects to the PCS through an 8-, 10-, 16-, 20-, 32-, 40-, 64-, or 66-bit interface,

depending on the transceiver data rate and protocol. Stratix V devices contain PCS hard IP to support

PCIe Gen3, Gen2, Gen1, Interlaken, 10GE, XAUI, GbE, SRIO, CPRI, and GPON protocols. All other

standard and proprietary protocols are supported through the transceiver PCS hard IP. The following

table lists the transceiver PCS features.

12 Low-Power Serial Transceivers SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Table 8: Transceiver PCS Features

Protocol Data Rates (Gbps) Transmitter Data Path Receiver Data Path

Custom PHY 0.6 to 8.5 Phase compensation FIFO, byte

serializer, 8B/10B encoder,

bit-slip, and channel bonding

Word aligner, de-skew FIFO,

rate match FIFO, 8B/10B

decoder, byte deserializer, and

byte ordering

Custom 10G

PHY 9.98 to 14.1 TX FIFO, gear box, and bit-slip RX FIFO and gear box

x1, x4, x8 PCIe

Gen1 and Gen2 2.5 and 5.0 Same as custom PHY plus PIPE

2.0 interface to core logic Same as custom PHY plus

PIPE 2.0 interface to core logic

x1, x4, x8 PCIe

Gen3 8 Phase compensation FIFO,

encoder, scrambler, gear box, and

bit-slip

Block synchronization, rate

match FIFO, decoder,

de-scrambler, and phase

compensation FIFO

10G Ethernet 10.3125 TX FIFO, 64/66 encoder,

scrambler, and gear box RX FIFO, 64/66 decoder,

de-scrambler, block synchro‐

nization, and gear box

Interlaken 4.9 to 14.1 TX FIFO, frame generator,

CRC-32 generator, scrambler,

disparity generator, and gear box

RX FIFO, frame generator,

CRC-32 checker, frame

decoder, descrambler,

disparity checker, block

synchronization, and gearbox

OTN 40 and

100

(4 +1) x 11.3 TX FIFO, channel bonding, and

byte serializer RX FIFO, lane deskew, and

byte de-serializer

(10 +1) x 11.3

GbE 1.25 Same as custom PHY plus GbE

state machine Same as custom PHY plus

GbE state machine

XAUI 3.125 to 4.25 Same as custom PHY plus XAUI

state machine for bonding four

channels

Same as custom PHY plus

XAUI state machine for re-

aligning four channels

SRIO 1.25 to 6.25 Same as custom PHY plus SRIO

V2.1 compliant x2 and x4 channel

bonding

Same as custom PHY plus

SRIO V2.1compliant x2 and

x4 deskew state machine

CPRI 0.6144 to 9.83 Same as custom PHY plus TX

deterministic latency Same as custom PHY plus RX

deterministic latency

GPON 1.25, 2.5, and 10 Same as custom PHY Same as custom PHY

SV51001

2015.10.01 Low-Power Serial Transceivers 13

Stratix V Device Overview Altera Corporation

Send Feedback

PCIe Gen3, Gen2, and Gen1 Hard IP (Embedded HardCopy Block)

Stratix V devices have PCIe hard IP designed for performance, ease-of-use, and increased functionality.

The PCIe hard IP consists of the PCS, data link, and transaction layers. The PCIe hard IP supports Gen3,

Gen2, and Gen1 end point and root port up to x8 lane configurations.

The Stratix V PCIe hard IP operates independently from the core logic, which allows the PCIe link to

wake up and complete link training in less than 100 ms while the Stratix V device completes loading the

programming file for the rest of the FPGA. The PCIe hard IP also provides added functionality, which

helps support emerging features such as Single Root I/O Virtualization (SR-IOV) or optional protocol

extensions. In addition, the Stratix V device PCIe hard IP has improved end-to-end data path protection

using ECC and enables device CvP.

In all Stratix V devices, the primary PCIe hard IP that supports CvP is always in the bottom left corner of

the device (IOBANK_B0L) when viewing the die from the top.

External Memory and GPIO

Each Stratix V I/O block has a hard FIFO that improves the resynchronization margin as data is

transferred from the external memory to the FPGA.

The hard FIFO also lowers PHY latency, resulting in higher random access performance. GPIOs include

on-chip dynamic termination to reduce the number of external components and minimize reflections.

On-package decoupling capacitors suppress noise on the power lines, which reduce noise coupling into

the I/Os. Memory banks are isolated to prevent core noise from coupling to the output, thus reducing

jitter and providing optimal signal integrity.

The external memory interface block uses advanced calibration algorithms to compensate for process,

voltage and temperature (PVT) variations in the FPGA and external memory components. The advanced

algorithms ensure maximum bandwidth and a robust timing margin across all conditions. Stratix V

devices deliver a complete memory solution with the High Performance Memory Controller II (HPMC II)

and UniPHY MegaCore® IP that simplifies a design for today’s advanced memory modules. The following

table lists external memory interface block performance.

Table 9: External Memory Interface Performance

The specifications listed in this table are performance targets. For a current achievable performance, use the

External Memory Interface Spec Estimator.

Interface Performance (MHz)

DDR3 933

DDR2 400

QDR II 350

QDR II+ 550

RLDRAM II 533

RLDRAM III 800

14 PCIe Gen3, Gen2, and Gen1 Hard IP (Embedded HardCopy Block) SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Related Information

External Memory Interface Spec Estimator

Adaptive Logic Module

Stratix V devices use an improved ALM to implement logic functions more efficiently. The Stratix V ALM

has eight inputs with a fracturable look-up table (LUT), two dedicated embedded adders, and four

dedicated registers.

The Stratix V ALM has the following enhancements:

• Packs 6% more logic when compared with the ALM found in Stratix IV devices.

• Implements select 7-input LUT-based functions, all 6-input logic functions, and two independent

functions consisting of smaller LUT sizes (such as two independent 4-input LUTs) to optimize core

usage.

• Adds more registers (four registers per 8-input fracturable LUT). More registers allow Stratix V

devices to maximize core performance at a higher core logic usage and provides easier timing closure

for register-rich and heavily pipelined designs.

The Quartus II software leverages the Stratix V ALM logic structure to deliver the highest performance,

optimal logic usage, and lowest compile times. The Quartus II software simplifies design re-use because it

automatically maps legacy Stratix designs into the new Stratix V ALM architecture.

Clocking

The Stratix V device core clock network is designed to support 800-MHz fabric operations and 1,066-

MHz and 1,600-Mbps external memory interfaces.

The clock network architecture is based on Altera’s proven global, quadrant, and peripheral clock

structure, which is supported by dedicated clock input pins and fractional clock synthesis PLLs. The

Quartus II software identifies all unused sections of the clock network and powers them down, which

reduces power consumption.

Fractional PLL

Stratix V devices contain up to 32 fractional PLLs.

You can use the fractional PLLs to reduce both the number of oscillators required on the board and the

clock pins used in the FPGA by synthesizing multiple clock frequencies from a single reference clock

source. In addition, you can use the fractional PLLs for clock network delay compensation, zero delay

buffering, and transmitter clocking for transceivers. Fractional PLLs can be individually configured for

integer mode or fractional mode with third-order delta-sigma modulation.

Embedded Memory

Stratix V devices contain two types of embedded memory blocks: MLAB (640-bit) and M20K (20-Kbit).

MLAB blocks are ideal for wide and shallow memories. M20K blocks are useful for supporting larger

memory configurations and include ECC.

SV51001

2015.10.01 Adaptive Logic Module 15

Stratix V Device Overview Altera Corporation

Send Feedback

Both types of memory blocks operate up to 600 MHz and can be configured to be a single- or dual-port

RAM, FIFO, ROM, or shift register. These memory blocks are flexible and support a number of memory

configurations, as shown in the following table.

Table 10: Embedded Memory Block Configuration

MLAB (640 Bits) M20K (20,480 Bits)

32x20

64x10

512x40

1Kx20

2Kx10

4Kx5

8Kx2

16Kx1

The Quartus II software simplifies design re-use by automatically mapping memory blocks from legacy

Stratix devices into the Stratix V memory architecture.

Variable Precision DSP Block

Stratix V FPGAs feature the industry’s first variable precision DSP block that you can configure to

natively support signal processing with precision ranging from 9x9 to 36x36.

You can independently configure each DSP block at compile time as either a dual 18x18 multiply

accumulate or a single 27x27 multiply accumulate. With a dedicated 64-bit cascade bus, you can cascade

multiple variable precision DSP blocks to implement even higher precision DSP functions efficiently. The

following table describes how variable precision is accommodated within a DSP block or by using

multiple blocks.

Table 11: Variable Precision DSP Block Configurations

Multiplier Size

(bits) DSP Block Resources Expected Usage

9x9 1/3 of variable precision DSP block Low precision fixed point

18x18 1/2 of variable precision DSP block Medium precision fixed point

27x27 1 variable precision DSP block High precision fixed or single precision

floating point

36x36 2 variable precision DSP blocks Very high precision fixed point

Complex multiplication is common in DSP algorithms. One of the most popular applications of complex

multipliers is the fast Fourier transform (FFT) algorithm, which increases precision requirements on only

one side of the multiplier. The variable precision DSP block is designed to support the FFT algorithm with

a proportional increase in DSP resources with precision growth. The following table lists complex

multiplication with variable precision DSP blocks.

16 Variable Precision DSP Block SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Table 12: Complex Multiplication with Variable Precision DSP Blocks

Multiplier Size

(bits) DSP Block Resources Expected Usage

18x18 2 variable precision DSP blocks Resource optimized FFTs

18x25 3 variable precision DSP blocks Accommodate bit growth through FFT stages

18x36 4 variable precision DSP blocks Highest precision FFT stages

27x27 4 variable precision DSP blocks Single precision floating point

For FFT applications with high dynamic range requirements, only the Altera® FFT MegaCore offers an

option of single precision floating point implementation, with the resource usage and performance similar

to high-precision fixed point implementations.

Other new features include:

• 64-bit accumulator, the largest in the industry

• Hard pre-adder, available in both 18- and 27-bit modes

• Cascaded output adders for efficient systolic FIR filters

• Internal coefficient register banks

• Enhanced independent multiplier operation

• Efficient support for single- and double-precision floating point arithmetic

• Ability to infer all the DSP block modes through HDL code using the Altera Complete Design Suite

The variable precision DSP block is ideal for higher bit precision in high-performance DSP applications.

At the same time, the variable precision DSP block can efficiently support the many existing 18-bit DSP

applications, such as high definition video processing and remote radio heads. Stratix V FPGAs, with the

variable precision DSP block architecture, are the only FPGA family that can efficiently support many

different precision levels, up to and including floating point implementations. This flexibility results in

increased system performance, reduced power consumption, and reduced architecture constraints for

system algorithm designers.

Power Management

Stratix V devices leverage FPGA architectural features and process technology advancements to reduce

total power consumption by up to 30% when compared with Stratix IV devices at the same performance

level.

Stratix V devices continue to provide programmable power technology, introduced in earlier generations

of Stratix FPGA families. The Quartus II software PowerPlay feature identifies critical timing paths in a

design and biases core logic in that path for high performance. PowerPlay also identifies non-critical

timing paths and biases core logic in that path for low power instead of high performance. PowerPlay

automatically biases core logic to meet performance and optimize power consumption.

Additionally, Stratix V devices have a number of hard IP blocks that reduce logic resources and deliver

substantial power savings when compared with soft implementations. The list includes PCIe Gen1/Gen2/

Gen3, Interlaken PCS, hard I/O FIFOs, and transceivers. Hard IP blocks consume up to 50% less power

than equivalent soft implementations.

SV51001

2015.10.01 Power Management 17

Stratix V Device Overview Altera Corporation

Send Feedback

Stratix V transceivers are designed for power efficiency. The transceiver channels consume 50% less

power than Stratix IV FPGAs. The transceiver PMA consumes approximately 90 mW at 6.5 Gbps and

170 mW at 12.5 Gbps.

Incremental Compilation

The Quartus II software incremental compilation feature reduces compilation time by up to 70% and

preserves performance to ease timing closure.

Incremental compilation supports top-down, bottom-up, and team-based design flows. Incremental

compilation facilitates modular hierarchical and team-based design flows where a team of designers work

in parallel on a design. Different designers or IP providers can develop and optimize different blocks of

the design independently, which you can then import into the top-level project.

Enhanced Configuration and CvP

Stratix V device configuration is enhanced for ease-of-use, speed, and cost.

Stratix V devices support a new 4-bit bus active serial mode (ASx4). ASx4 supports up to a 400Mbps data

rate using small low-cost quad interface Flash devices. ASx4 mode is easy to use and offers an ideal

balance between cost and speed. Finally, the fast passive parallel (FPP) interface is enhanced to support 8-,

16-, and 32-bit data widths to meet a wide range of performance and cost goals.

You can configure Stratix V FPGAs using CvP with PCIe. CvP with PCIe divides the configuration

process into two parts: the PCIe hard IP and periphery and the core logic fabric. CvP uses a much smaller

amount of external memory (flash or ROM) because CvP has to store only the configuration file for the

PCIe hard IP and periphery. The 100-ms power-up to active time (for PCIe) is much easier to achieve

when only the PCIe hard IP and periphery are loaded. After the PCIe hard IP and periphery are loaded

and the root port is booted up, application software running on the root port can send the configuration

file for the FPGA fabric across the PCIe link where the file is loaded into the FPGA. The FPGA is then

fully configured and functional.

The following table lists the configuration modes available for Stratix V devices.

Table 13: Configuration Modes for Stratix V Devices

Mode Fast or

Slow POR Compres‐

sion Encryption Remote

Update Data Width Max Clock

Rate (MHz) Max Data Rate

(Mbps)

Active Serial

(AS) Yes Yes Yes Yes 1, 4 100 400

Passive Serial

(PS) Yes Yes Yes — 1 125 125

Fast Passive

Parallel (FPP) Yes Yes Yes Yes (14) 8, 16, 32 125 (15) 3,000

(14) Remote update support with the Parallel Flash Loader.

(15) The maximum clock rate is 125 MHz for x8 and x16 FPP, but only 100 MHz for x32 FPP.

18 Incremental Compilation SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Mode Fast or

Slow POR Compres‐

sion Encryption Remote

Update Data Width Max Clock

Rate (MHz) Max Data Rate

(Mbps)

CvP — — Yes Yes 1, 2, 4, 8 — 3,000

Partial

Reconfigura‐

tion

— — Yes Yes 16 125 2,000

JTAG — — — — 1 33 33

Partial Reconfiguration

Partial reconfiguration allows you to reconfigure part of the FPGA while other sections continue to

operate.

This capability is required in systems where uptime is critical because partial reconfiguration allows you

to make updates or adjust functionality without disrupting services. While lowering power and cost,

partial reconfiguration also increases the effective logic density by removing the necessity to place FPGA

functions that do not operate simultaneously. Instead, you can store these functions in external memory

and load them as required. This capability reduces the size of the FPGA by allowing multiple applications

on a single FPGA, saving board space and reducing power.

You no longer need to know all the details of the FPGA architecture to perform partial reconfiguration.

Altera simplifies the process by extending the power of incremental compilation used in earlier versions

of the Quartus II software.

Partial reconfiguration is supported in the following configurations:

• Partial reconfiguration through the FPP x16 I/O interface

• CvP

• Soft internal core, such as the Nios® II processor.

Automatic Single Event Upset Error Detection and Correction

Stratix V devices offer single event upset (SEU) error detection and correction circuitry that is robust and

easy to use.

The correction circuitry includes protection for configuration RAM (CRAM) programming bits and user

memories. The CRAM is protected by a continuously running cyclical redundancy check (CRC) error

detection circuit with integrated ECC that automatically corrects one or double-adjacent bit errors and

detects higher order multi-bit errors. When more than two errors occur, correction is available through a

core programming file reload that refreshes a design while the FPGA is operating.

The physical layout of the FPGA is optimized to make the majority of multi-bit upsets appear as

independent single- or double-adjacent bit errors, which are automatically corrected by the integrated

CRAM ECC circuitry. In addition to the CRAM protection in Stratix V devices, user memories include

integrated ECC circuitry and are layout-optimized to enable error detection of 3-bit errors and correction

for 2-bit errors.

SV51001

2015.10.01 Partial Reconfiguration 19

Stratix V Device Overview Altera Corporation

Send Feedback

HardCopy V Devices

HardCopy V ASICs offer the lowest risk and lowest total cost in ASIC designs with embedded high-speed

transceivers. You can prototype and debug with Stratix V FPGAs, then use HardCopy V ASICs for

volume production. The proven turnkey process creates a functionally equivalent HardCopy V ASIC with

or without embedded transceivers to meet all timing constraints in as little as 12 weeks.

The powerful combination of Stratix V FPGAs and HardCopy V ASICs can help you meet your design

requirements. Whether you plan for ASIC production and require the lowest-risk, lowest-cost path from

specification to production or require a cost reduction path for your FPGA-based systems, Altera

provides the optimal solution for power, performance, and device bandwidth.

Ordering Information

This section describes ordering information for Stratix V GT, GX, GS, and E devices.

The following figure shows the ordering codes for Stratix V devices.

Figure 2: Ordering Information for Stratix V Devices

Family Signature

Embedded Hard IP

Block Variant

Transceiver Count

Transceiver PMA

Speed Grade

Package Type

Ball Array Dimension

Corresponds to pin count

Operating Temperature

Transceiver PCS and

FPGA Fabric Speed Grade

Optional Suffix (2)

(1)

GX : 14.1-Gbps transceivers

GT : 28.05-Gbps transceivers

GS : DSP-Oriented

E : Highest logic density,

no transceivers

M : Mainstream

E : Extended

5S : Stratix V

A3 C5 D3 E9

GX GT GS E

A4 C7 D4 EB

A5 D5

A7 D6

A9 D8

E : 12

H : 24

K : 36

N : 48

R : 66

1 (fastest)

3 (3)

F : FineLine BGA

H : Hybrid FineLine BGA

29 : 780 pins

35 : 1,152 pins

40 : 1,517 pins

43 : 1,760 pins

45 : 1,932 pins

C : Commercial (0 to 85°C)

I : Industrial (–40 to 100°C)

1 (fastest)

L : Low-power device

N : Lead-free packaging

YY : Special order devices (3)

ES : Engineering sample silicon

5S GX M A5 K 3F 35 C 2 L N YY ES

Member Code

Family Variant

Notes:

(1) Stratix V mainstream “M” devices have exactly one instantiation of PCI Express hard IP. Extended “E” devices have either two or four instantiations of PCI Express hard IP,

depending on the device and package combination. For non-transceiver Stratix V devices, this character does not appear in the part number.

(2) You can select one or two of these options, or you can ignore these options.

(3) YY parts can support transceiver operations up to 10.3125 Gbps.

20 HardCopy V Devices SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Document Revision History

Table 14: Document Revision History

Date Version Changes Made

October 2015 2015.10.01 Changed heading in the "Ordering Information for Stratix V

Devices" figure to "Embedded Hard IP Block Variant".

January 2015 2015.01.15 • Added ALM counts and device package sizes to the four

device family features tables.

• In the "Stratix V GX Device Features" table, changed the

number of DDR3 SDRAM x72 DIMM Interfaces for the

5SGXA3 and 5SGXA4 devices to 6. Also added footnote

to this row.

• Deleted listings for 40GBASE-R and 100GBASE-R

Ethernet from the "Transceiver PCS Features" table in

the "Low-Power Serial Transceivers" section.

• Added YY code to the Optional Suffix category in the

"Ordering Information for Stratix V Devices" figure.

April 2014 2014.04.08 Updated "Variable precision DSP blocks" section of the

"Features Summary" table to 600 MHz performance.

April 2014 2014.04.03 • Updated GPIOs section of the "Features Summary" table

to 1.6 Gbps LVDS.

• Changed clocking speed to 800 MHz in the "Features

Summary" and the "Clocking" sections.

January 2014 2014.01.10 • Added link to Altera Product Selector in the "Stratix V

Family Plan" section.

• Corrected DDR2 performance from 533 MHz to

400 MHz.

• Updated "Device Migration List Across All Stratix V

Device Variants" table.

May 2013 2013.05.06 • Added link to the known document issues in the

Knowledge Base.

• Updated backplane support information.

• Added a note about the number of I/Os to each table in

the "Stratix V Family Plan" section.

• Updated the "Ordering Information for Stratix V

Devices" figure.

December 2012 3.1 • Updated Table 6 and Table 13.

• Updated Figure 2.

SV51001

2015.10.01 Document Revision History 21

Stratix V Device Overview Altera Corporation

Send Feedback

Date Version Changes Made

June 2012 3.0 • Converted chapter to stand-alone format and removed

from the Stratix V handbook.

• Changed title of document to Stratix V Device Overview

• Updated Figure 1.

• Minor text edits.

February 2012 2.3 • Updated Table 1–2, Table 1–3, Table 1–4, and Table 1–5.

• Updated Figure 1–2.

• Updated “Automatic Single Event Upset Error Detection

and Correction” on page 18.

• Minor text edits.

December 2011 2.2 Updated Table 1–2 and Table 1–3.

November 2011 2.1 • Changed Stratix V GT transceiver speed from 28 Gbps to

28.05 Gbps.

• Updated Figure 1–2.

November 2011 2.0 • Revised Figure 1–2.

• Updated Table 1–5.

• Minor text edits.

September 2011 1.10 Updated Table 1–2, Table 1–3, and Table 1–4.

September 2011 1.9 • Updated Table 1–1, Table 1–2, Table 1–3, Table 1–4, and

Table 1–5.

• Updated Figure 1–2.

• Minor text edits.

June 2011 1.8 Changed 800 MHz to 1,066 MHz for DDR3 in Table 1–8

and in text.

May 2011 1.7 • For Stratix V GT devices, changed 14.1 Gbps to

12.5 Gbps.

• Changed Configuration via PCIe to Configuration via

Protocol

• Updated Table 1–1, Table 1–2, Table 1–3, Table 1–4,

Table 1–5, and Table 1–6.

• Chapter moved to Volume 1.

January 2011 1.6 • Added Stratix V GS information.

• Updated tables listing device features.

• Added device migration information.

• Updated 12.5-Gbps transceivers to 14.1-Gbps

transceivers

December 2010 1.5 Updated Table 1-1.

22 Document Revision History SV51001

2015.10.01

Altera Corporation Stratix V Device Overview

Send Feedback

Date Version Changes Made

December 2010 1.4 • Updated Table 1-1.

• Updated Figure 1-2.

• Converted to the new template.

• Minor text edits.

July 2010 1.3 Updated Table 1–5

July 2010 1.2 • Updated “Features Summary” on page 1–2

• Updated resource counts in Table 1–1 and Table 1–2

• Removed “Interlaken PCS Hard IP” and “10G Ethernet

Hard IP”

• Added “40G and 100G Ethernet Hard IP (Embedded

HardCopy Block)” on page 1–7

• Added information about Configuration via PCIe

• Added “Partial Reconfiguration” on page 1–12

• Added “Ordering Information” on page 1–14

May 2010 1.1 Updated part numbers in Table 1–1 and Table 1–2

April 2010 1.0 Initial release

SV51001

2015.10.01 Document Revision History 23

Stratix V Device Overview Altera Corporation

Send Feedback

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Altera:

5SGXEB5R2F40C2N 5SGSMD3E2H29I3L 5SGSED6N1F45I2N 5SGSED8K1F40I2N 5SGXEBBR2H43I3L

5SGXEA3K2F40C1N 5SGXEA9K3H40I3LN 5SGXEB9R2H43I2N 5SGXMA4H2F35I3LN 5SGXMA9N3F45I3LN

5SGSMD6K2F40C2LN 5SGSMD5K1F40C2L 5SGSMD4H2F35C3N 5SGXMA7N1F40C2LN 5SGXMA5H3F35I3LN

5SGSMD3H2F35I2N 5SGXEA4K1F35C2LN 5SGXMA4K1F40C2N 5SGXMA9N3F45C4N 5SGSMD4E2H29C2LN

5SGXMBBR2H43I2LN 5SGXEA7K3F35C2NES 5SGXMA5K3F35C3N 5SGXEB6R2F43C3ES 5SGXEA7N1F45C2N

5SGSMD6N2F45I2N 5SGXEA5H2F35I2L 5SGXEA7H2F35I3 5SGXEA5K3F35I3LN 5SGXMA7N2F40C1N

5SGXMA3E3H29I4N 5SGXEA7N3F40C2LN 5SGXEB5R3F40C2LN 5SGSMD3E1H29C2L 5SGXEA7N2F40C2NES

5SGXEA4K2F40I2LN 5SGXMA7H1F35C2LN 5SGXEA7N3F40C3 5SEEBH40C2LN 5SEEBH40I4N

5SGXMA7N3F40I3 5SGSMD3E3H29C2LN 5SGSMD5H3F35I4 5SGXEA5N2F40I2N 5SGXMA7N2F45C1N

5SGXMA3H3F35C4N 5SGXMABN3F45C4N 5SGXEA7N2F45C3N 5SGXEA7H3F35I3LN 5SGXMA5K2F35C2N

5SGXEA7H3F35C2ES 5SGSED8N3F45I3LN 5SGXEA9K2H40I3N 5SGXEABN3F45I3L 5SGSMD5K2F40I3N

5SGXEA9N3F45I3LN 5SGXEA3H3F35I3LN 5SGSMD8N3F45C3N 5SGXEA4H1F35C2N 5SGXMA7K2F40I3N

5SGSED6K2F40C2LN 5SGXMA5N2F45C3N 5SGXEB9R2H43I3N 5SGXMA7N3F45I4N 5SGSED8N1F45C2LN

5SGSMD5K1F40I2N 5SGXMA7N2F40I2LN 5SGXMB6R2F43C2N 5SGXMA3E2H29I3LN 5SGXEA7K2F40C2LN

5SGXEA7N3F45C4N 5SGSMD8N2F45I2N 5SGXEA7N2F40I3 5SGXEA7K1F35C2L 5SGXEA7K2F40C3ES

5SGXMA3E1H29C2N 5SGSMD6K2F40I2N 5SGSMD8N1F45C2LN 5SGXMB5R3F40I3N 5SGXEA9N2F45I2N

5SGXEA3K3F35C2L 5SGTMC7K2F40I3N 5SGSMD4E2H29I3N 5SGSED6N3F45C2N 5SGSMD3H2F35I3L

5SGXMA9K3H40I3N 5SGXEB6R2F40C3 5SGXMB6R1F43C2LN 5SGSMD3H3F35C3N 5SGXEA4K2F35C2LN

5SGSMD4E2H29C2N 5SGSMD4K2F40I3LN 5SGXMA3K3F35I3N 5SGXEA5K2F35C2L 5SGXMA7N3F45C2LN

5SGSMD3H2F35C2LN 5SGXMA4K3F35C2LN 5SGXEA7K2F35C3ES 5SGXMB6R3F43I4N 5SGXMA7N2F45C3