Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HRA Series SMBJ-HRA Series RoHS Pb e3 Description Uni-directional The SMBJ-HRA High Reliability series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Bi-directional Features * Excellent clamping capability * Low incremental surge resistance * Typical IR 1A for VR > 11.10V * SMT for minimal board footprint * Low profile package * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) * EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) * Built-in strain relief * Fast response time: typically less than 1.0ps from 0V to BV min Agency Approvals AGENCY AGENCY FILE NUMBER E128662/E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25C by 10/1000s Waveform (Fig.2)(Note 1), (Note 2) PPPM 600 W Power Dissipation on Infinite Heat Sink at TL=50OC PM(AV) 5.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 100 A Maximum Instantaneous Forward Voltage at 50A for Unidirectional Only VF 3.5V V TJ , TSTG -65 to 150 C Typical Thermal Resistance Junction to Lead RuJL 20 C/W Typical Thermal Resistance Junction to Ambient RuJA 100 C/W Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25OC per Fig. 3. * 600W peak pulse power capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * VBR @TJ= VBR@25C x (1+T x (TJ - 25)) (T:Temperature Coefficient) * Glass passivated chip junction * High temperature soldering guaranteed: 260C/40 seconds at terminals * UL Recognized compound meeting flammability rating V-0 * Meet MSL level1, per J-STD-020, LF maximun peak of 260C * Matte tin lead-free plated * Halogen free and RoHS compliant * 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01 Applications 2. Mounted on copper pad area of 0.2x0.2" (5.0 x 5.0mm) to each terminal. SMBJ-HR components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Functional Diagram Bi-directional Cathode Anode Uni-directional 1 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HRA Series Electrical Characteristics (T =25C unless otherwise noted) A Part Number (Uni) Part Number (Bi) SMBJ5.0A-HRA SMBJ6.0A-HRA SMBJ6.5A-HRA SMBJ7.0A-HRA SMBJ7.5A-HRA SMBJ8.0A-HRA SMBJ8.5A-HRA SMBJ9.0A-HRA SMBJ10A-HRA SMBJ11A-HRA SMBJ12A-HRA SMBJ13A-HRA SMBJ14A-HRA SMBJ15A-HRA SMBJ16A-HRA SMBJ17A-HRA SMBJ18A-HRA SMBJ20A-HRA SMBJ22A-HRA SMBJ24A-HRA SMBJ26A-HRA SMBJ28A-HRA SMBJ30A-HRA SMBJ33A-HRA SMBJ36A-HRA SMBJ40A-HRA SMBJ43A-HRA SMBJ45A-HRA SMBJ48A-HRA SMBJ51A-HRA SMBJ54A-HRA SMBJ58A-HRA SMBJ60A-HRA SMBJ64A-HRA SMBJ70A-HRA SMBJ75A-HRA SMBJ78A-HRA SMBJ85A-HRA - SMBJ5.0CA-HRA SMBJ6.0CA-HRA SMBJ6.5CA-HRA SMBJ7.0CA-HRA SMBJ7.5CA-HRA SMBJ8.0CA-HRA SMBJ8.5CA-HRA SMBJ9.0CA-HRA SMBJ10CA-HRA SMBJ11CA-HRA SMBJ12CA-HRA SMBJ13CA-HRA SMBJ14CA-HRA SMBJ15CA-HRA SMBJ16CA-HRA SMBJ17CA-HRA SMBJ18CA-HRA SMBJ20CA-HRA SMBJ22CA-HRA SMBJ24CA-HRA SMBJ26CA-HRA SMBJ28CA-HRA SMBJ30CA-HRA SMBJ33CA-HRA SMBJ36CA-HRA SMBJ40CA-HRA SMBJ43CA-HRA SMBJ45CA-HRA SMBJ48CA-HRA SMBJ51CA-HRA SMBJ54CA-HRA SMBJ58CA-HRA SMBJ60CA-HRA SMBJ64CA-HRA SMBJ70CA-HRA SMBJ75CA-HRA SMBJ78CA-HRA SMBJ85CA-HRA SMBJ90CA-HRA SMBJ100CA-HRA SMBJ110CA-HRA SMBJ120CA-HRA SMBJ130CA-HRA SMBJ150CA-HRA SMBJ160CA-HRA SMBJ170CA-HRA Marking UNI BI KEH KGH KKH KMH KPH KRH KTH KVH KXH KZH LEH LGH LKH LMH LPH LRH LTH LVH LXH LZH MEH MGH MK H MMH MPH MRH MTH MVH MXH MZH NEH NGH NKH NMH NPH NRH NTH NVH - AEH AGH AKH AMH APH ARH ATH AVH AXH AZH BEH BGH BKH BMH BPH BRH BTH BVH BXH BZH CEH CGH CKH CMH CPH CRH CTH CVH CXH CZH DEH DGH DKH DMH DPH DRH DTH DVH DXH DZH EEH EGH EKH EMH EPH ER Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Reverse Stand off Voltage VR (Volts) 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 Note: 1. For bidirectional type having VR of 10 volts and less, the IR limit is double. 2. 100% High Temperature Storage Life test and Reflow Simulation. 3. 100% HTRB(High Temperature Reverse Bias). For Unidirectional, 150OC/100%VR/96hours, for Bidirectional, 150OC/100%VR/192hrs(96hours for each direction for Bidirectional). 4. IR measured at room temperature +25OC (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 2 Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (A) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 65.3 58.3 53.6 50.0 46.6 44.2 41.7 39.0 35.3 33.0 30.2 28.0 25.9 24.6 23.1 21.8 20.6 18.6 16.9 15.5 14.3 13.3 12.4 11.3 10.4 9.3 8.7 8.3 7.8 7.3 6.9 6.5 6.2 5.9 5.3 5.0 4.8 4.4 4.1 3.7 3.4 3.1 2.9 2.5 2.3 2.2 800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HRA Series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IR IT VR VBR Vc V Ipp Ipp PPPM VR VBR VC IR VF IT IR Peak Pulse Power Dissipation (IPP x VC)-- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients PPPM-Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS Current Through TVS 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 0.000001 0.00001 0.0001 0.001 td-Pulse Width (sec.) Time continues on next page. 3 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HRA Series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 tr=10sec Half Value IPPM IPPM ( ) 2 50 0 TA-Ambient temperature (C) td 1.0 0 2.0 3.0 4.0 Figure 6 - Steady State Power Dissipation Derating Curve 10000 PM(AV), Steady State Power Dissipation (W) 6 Bi-directional V=0V 1000 Cj (pF) 10/1000sec. Waveform as defined by R.E.A t-Time (ms) Figure 5 - Typical Junction Capacitance Uni-directional V=0V Uni-directional @VR 100 Bi-directional @VR 10 Tj=25C f=1.0MHz Vsig=50mVp-p 1 1.0 10.0 100.0 VBR - Reverse Breakdown Voltage (V) 100 80 60 40 20 0 10 100 Number of Cycles at 60 Hz (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 4 3 2 1 0 25 50 75 100 125 Temperature (C)(C) TA - TL-Lead Ambient Temperature (Power Dissipation on Infinite H eat Sink ) 120 1 5 0 1000.0 Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only IFSM - Peak Forward Surge Current (A) Peak Value IPPM 100 175 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 4 150 175 Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HRA Series Soldering Parameters Pre Heat Lead-free assembly - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25C t 25C to Peak Time (t) Environmental Specifications Physical Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 MSL JEDEC-J-STD-020, Level 1 Weight 0.003 ounce, 0.093 grams Case JEDEC DO214AA. Molded plastic body over glass passivated junction Polarity Color band denotes cathode except Bidirectional H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102 RSH JESD22-B106 Dimensions DO-214AA (SMB J-Bend) Dimensions Cathode Band (for Uni-directional products only) C A B H D F E G J K L Inches Millimeters Min Max Min Max A 0.077 B 0.160 0.086 1.950 2.200 0.180 4.060 4.570 C 0.130 0.155 3.300 3.940 D 0.084 0.096 2.130 2.440 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.205 0.220 5.210 5.590 H 0.006 0.012 0.152 0.305 I 0.089 - 2.260 - J 0.085 - 2.160 - K - 0.107 - 2.740 L 0.085 - 2.160 - I Solder Pads (all dimensions in mm) 5 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HRA Series Part Numbering System SMBJ Part Marking System XXX C A -HR A Cathode Band WITHOUT GROUP B TEST (for Uni-directional products only) F HIGH RELIABILITY 5% VOLTAGE TOLERANCE BI-DIRECTIONAL VOLTAGE XX SERIES YMXXX Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Part number Component Package SMBJxxxXX-HRA DO-214AA Packaging Option Quantity 3000 Tape & Reel - 12mm tape/13" reel Packaging Specification EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) 0.47 (12.0) Cathode 0.315 (8.0) Optional 7" 7.0 (187) 13" 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 0.059 DIA (1.5) (for unidirectional version only) Cover tape Dimensions are in inches (and millimeters). Direction of Feed 6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: SMBJ22A-HRA SMBJ14A-HRA SMBJ8.0A-HRA SMBJ45A-HRA SMBJ40A-HRA SMBJ70A-HRA SMBJ58CA-HRA SMBJ13CA-HRA SMBJ18A-HRA SMBJ10CA-HRA SMBJ5.0A-HRA SMBJ15A-HRA SMBJ6.0CA-HRA SMBJ10AHRA SMBJ170CA-HRA SMBJ16A-HRA SMBJ33A-HRA SMBJ7.5A-HRA SMBJ7.0CA-HRA SMBJ7.5CA-HRA SMBJ75CA-HRA SMBJ11CA-HRA SMBJ28CA-HRA SMBJ78CA-HRA SMBJ20A-HRA SMBJ20CA-HRA SMBJ85AHRA SMBJ16CA-HRA SMBJ54CA-HRA SMBJ7.0A-HRA SMBJ120CA-HRA SMBJ85CA-HRA SMBJ11A-HRA SMBJ60A-HRA SMBJ130CA-HRA SMBJ45CA-HRA SMBJ26CA-HRA SMBJ8.5CA-HRA SMBJ30CA-HRA SMBJ18CA-HRA SMBJ48CA-HRA SMBJ58A-HRA SMBJ8.5A-HRA SMBJ33CA-HRA SMBJ17CA-HRA SMBJ110CA-HRA SMBJ78A-HRA SMBJ22CA-HRA SMBJ64A-HRA SMBJ26A-HRA SMBJ43A-HRA SMBJ6.0AHRA SMBJ6.5A-HRA SMBJ12CA-HRA SMBJ5.0CA-HRA SMBJ14CA-HRA SMBJ9.0CA-HRA SMBJ90CA-HRA SMBJ100CA-HRA SMBJ43CA-HRA SMBJ60CA-HRA SMBJ54A-HRA SMBJ36CA-HRA SMBJ6.5CA-HRA SMBJ30A-HRA SMBJ13A-HRA SMBJ17A-HRA SMBJ9.0A-HRA SMBJ12A-HRA SMBJ24A-HRA SMBJ160CA-HRA SMBJ51CA-HRA SMBJ48A-HRA SMBJ150CA-HRA SMBJ75A-HRA SMBJ51A-HRA SMBJ28A-HRA SMBJ40CAHRA SMBJ24CA-HRA SMBJ36A-HRA SMBJ8.0CA-HRA SMBJ64CA-HRA SMBJ15CA-HRA SMBJ70CA-HRA