VCC6-QAA-150M00 - Vectron International, Inc.

Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

VCC6-Q/R Series

2.5 and 3.3 volt LVPECL Crystal Oscillator

The VCC6 Crystal Oscillator

Features

• 2.5 or 3.3V LVPECL

• 3rd Overtone Crystal for best jitter performance

• Output frequencies to 270 MHz

• Low Jitter < 1 pS rms, 12kHz to 20MHz

• Enable/Disable for test and board debug

• -10/70 or –40/85 °C operating temperature

• Hermetically sealed ceramic SMD package

• Product is compliant to RoHS directive

Applications

• SONET/SDH/DWDM

• Fiber Channel

• Ethernet, Gigabit Ethernet

• Storage Area Network

• Digital Video

• Broadband Access

Description

Vectron’s VCC6 Crystal Oscillator (XO) is quartz

stabilized square wave generator with a LV-PECL

output, operating off a 3.3 volt supply.

The VCC6 uses 3rd overtone crystals for

frequencies under 200MHz, resulting in low jitter

performance, typically 0.3pS rms in the 12 kHz to

20MHz band.

OUT

Output

Buffer /

Disable

Enable/Disable

OUT

VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

Performance Characteristics

Table 1. Electrical Performance

Parameter Symbol

Min Typical Maximum Units

Frequency fO 10 270 MHz

Supply Voltage1, 3.3V Q option

2.5V R option VDD 3.15

2.375 3.3

2.5 3.45

2.625 V

Supply Current IDD 98 mA

Output Logic Levels, 0/70°C

Output Logic High2

Output Logic Low2

VOH

VOL

VDD-1.025

VDD-1.810

VDD-0.880

VDD-1.620

Output Logic Levels, -40/85°C

Output Logic High2

Output Logic Low2

VOH

VOL

VDD-1.085

VDD-1.830

VDD-0.880

VDD-1.555

Transition Times

Rise Time2

Fall Time2

600

Symmetry or Duty Cycle3 SYM 45 50 55 %

Operating temperature (ordering option) TOP -10/70 or –40/85 °C

Stability (ordering option)4 deltaF/F

±25, ±50 or ±100 ppm

Jitter, 12kHz to 20MHz5

Cycle to Cycle, rms

Cycle to Cycle, peak-peak

Period Jitter, rms

Period Jitter, peak-peak

0.3

4.8

2.7

0.7 pS

Output Enabled6 VIH 0.7*VDD V

Output Disabled6 VIL 0.3*VDD V

Output Enable/Disable time tE/D 200 nS

Enable/Disable Leakage Current IIL ±200 uA

Output Enable Pull-Up Resistor6

Output Enabled

Output Disabled

Kohm

Mohm

1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible and terminated to ground.

2. Figure 1 defines these parameters. Figure 2 illustrates the operating conditions under which these parameters are tested and specified.

3. Symmetry is measured defined as On Time/Period.

4. Includes calibration tolerance, operating temperature, supply voltage variations, aging (40 degreesC/10 years) and shock and vibration (not under

operation).

5. Measurements made on a VCC6-QAB-155M520 using an Agilent E5052A for phase noise and LeCroy 8600, 25K samples for jitter.

6. Output will be enabled if Enable/Disable is left open. The pull resistor changes to a higher value, operating in a “power saving mode” when

Enable/Disable is set to a logic 0.

Figure 1. Output Waveform Figure 2. Typical Output Test Conditions (25±5°C)

80%

20%

Period

On Time

VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

Outline Diagram and Pin Out

Table 2. VCC6-QAx Pinout

Pin # Symbol Function

1 NC This pin has no internal connection and is floating.

2 E/D Enable/Disable Function

3 GND Ground

4 fO Output Frequency

5 Cfo Complementary Output Frequency

6 VDD Supply Voltage

Gold over Nickel plating

Figure 3 Optional VCC6-QAx Package Drawing

Table 3. VCC6-QCx Pinout

Pin # Symbol Function

1 E/D Enable/Disable Function

2 NC This pin has no internal connection and is floating.

3 GND Ground

4 fO Output Frequency

5 Cfo Complementary Output Frequency

6 VDD Supply Voltage

Gold over Nickel plating

Figure 4. VCC6-QCx and VCC6-QAx Package Drawing

VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

Terminating PECL Outputs

The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in

Figure 5. There are numerous application notes on terminating and interfacing PECL logic and the two most

common methods are a single resistor to ground, Figure 6, and a pull-up/pull-down scheme as shown in

Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic

requirements of the next stage.

One of the most important considerations is terminating the Output and Complementary Outputs equally.

An unused output should not be left un-terminated, and if it one of the two outputs is left open it will result in

excessive jitter on both. PC board layout must take this and 50 ohm impedance matching into account.

Load matching and power supply noise are the main contributors to jitter related problems.

Figure 5. Standard PECL Output Configuration

Figure 6. Single Resistor Termination Figure 7. Pull-up Pull-down Termination

Resistor value are typically: Resistor values are typically:

120 to 240ohms for 3.3V 130 and 82 ohms for 3.3V

82 to 120 ohms for 2.5V 240 and 62 ohms for 2.5V

VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

Enable/Disable Functional Description

Under normal operation the Enable/Disable is left open, or set to a logic high state, and the VCC6 is in

oscillation mode and outputs are enabled (active). When the E/D is set to a logic low, the oscillator stops

and the both the output and complementary outputs are in a high impedance state. This helps facilitate

board testing and troubleshooting.

Power Saving Pull-Up Resistor

The E/D pull-up resistor changes in response to the input logic level; the pull-up resistor is a large value

when E/D is set to a logic low, which reduces the current consumed. When E/D is open, or set to a logic

high, the pull-up resistance becomes a smaller value which helps decrease the effects of external noise.

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional

operation is not implied at these or any other conditions in excess of conditions represented in the

operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may

adversely affect device reliability.

Table 4. Absolute Maximum Ratings

Parameter Symbol Ratings Unit

Power Supply VDD -0.5 to +7.0 Vdc

Enable/Disable VIN -0.5 to VDD+0.5 Vdc

Storage Temperature Tstorage -55/125 °C

Reliability

The VCC6 qualification tests included:

Table 5. Environnemental Compliance

Parameter Conditions

Mechanical Shock MIL-STD-883 Method 2002

Mechanical Vibration MIL-STD-883 Method 2007

Solderability MIL-STD-883 Method 2003

Gross and Fine Leak MIL-STD-883 Method 1014

Resistance to Solvents MIL-STD-883 Method 2016

Handling Precautions

Although ESD protection circuitry has been designed into the the VCC6, proper precautions should be taken

when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for

ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit

parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a

standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be

used for comparison purposes.

Table 6. ESD Ratings

Model Minimum Conditions

Human Body Model 1500 MIL-STD-883 Method 3015

Charged Device Model 1000

VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

IR Reflow and Suggested Pad Size Layout

The VCC6 has been qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and

time intervals listed are based on the Pb-Free small body requirements and maximum parameters are listed

in Table 6, lower temperatures are also acceptable. The VCC6 is hermetically sealed so an aqueous wash

is not an issue. Frequencies >200MHz will need to be reflowed at 220C max.

Table 7. Reflow Profile (IPC/JEDEC J-STD-020B)

Parameter Symbol Value

PreHeat Time t S 60 sec Min, 200 sec Max

Ramp Up R UP 3 oC/sec Max

Time Above 217 oC t L 60 sec Min, 150 sec Max

Time To Peak Temperature t AMB-P 480 sec Max

Time At 260 oC (max) t P 10 sec Max

Time At 240°C (max) tp2 60 sec MAX

Ramp Down R DN 6 oC/sec Max

Figure 8. IR Reflow Diagram

Figure 9. Pad Size Diagram

VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

GFJ

Tape and Reel

Figure 10. Tape and Reel Diagram

Table 8. Tape and Reel Dimensions (mm)

Tape Dimensions Reel Dimensions # Per

Product A B C D E F G H I J K L Reel

VCC6 16 7.5 1.5 4 8 2 21 13 60 2 17 180 250

VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

Table 9. Standard Frequencies (MHz)

19.440 27.000 27.027 35.000 37.000 38.880

40.000 40.680 48.000 50.000 52.300 62.500

64.000 64.375 74.1758 74.250 76.800 77.760

80.000 83.125 87.000 90.000 91.875 93.000

98.304 100.000 105.000 106.000 106.250 110.000

125.000 130.000 130.5882 133.000 134.560729 135.000

136.000 143.000 145.221 150.000 153.500 155.520

156.000 156.250 156.256 156.260 159.375 160.000

160.160 161.1328 163.235 164.3555 165.000 166.000

166.6286 166.6667 166.67 167.00 167.3316 168.200912

171.000 173.3707 175.000 180.000 187.500 190.000

195.3125 200.000 212.500 250.000 260.000

Other frequencies may be available upon request. Standard frequencies are frequencies which the crystal

has been designed and does not imply a stock position.

Ordering Information

VCC6 – Qxx – xxxMxx

Product Family Frequency MHz

Crystal Oscillator example: 125M00= 125.000

Supply Voltage, Output Stability Options/Temperature

Q=3.3V, LVPECL A: ±100ppm -10 to 70°C

R=2.5V, LVPECL B: ±50ppm -10 to 70°C

Enable/Disable C: ±100ppm -40 to 85°C

A: E/D is on Pin 2, Pin 1 is a NC D: ±50ppm -40 to 85°C

C: E/D is on Pin 1, Pin 2 is a NC E: ±25ppm -10 to 70°C

F: ±25ppm -40 to 85°C

NOTE: Not all combinations of options are available.

A ±20ppm option over -10/70°C 3.3V, VCC6-107-frequency, is also available

A ±20ppm option over -10/70°C 2.5V, VCC6-110-frequency, is also available.

www.vectron.com

Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed

as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

VCC6-Q/R (REVISION DATE: September 07, 2005

)

For Additional Information, Please Contact:

USA: Vectron International • 267 Lowell Road, Hudson, NH 03051

• Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON

EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany •

Tel: 49 (0) 7268 8010 • Fax: 49 (0) 7268 801281

ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd., WaiGaoQiao Free

Trade Zone, Pudong New Area Shanghai, China 200131

•Tel: 8621 50480777 • Fax: 8621 50481881