LT4356-1/LT4356-2 Surge Stopper FEATURES DESCRIPTION n The LT(R)4356 surge stopper protects loads from high voltage transients. It regulates the output during an overvoltage event, such as load dump in automobiles, by controlling the gate of an external N-channel MOSFET. The output is limited to a safe value thereby allowing the loads to continue functioning. The LT4356 also monitors the voltage drop between the VCC and SNS pins to protect against overcurrent faults. An internal amplifier limits the current sense voltage to 50mV. In either fault condition, a timer is started inversely proportional to MOSFET stress. If the timer expires, the FLT pin pulls low to warn of an impending power down. If the condition persists, the MOSFET is turned off. After a cool down period, the GATE pin pulls up turning on the MOSFET again. n n n n n n n n n n n n Stops High Voltage Surges Adjustable Output Clamp Voltage Overcurrent Protection Wide Operation Range: 4V to 80V Reverse Input Protection to -60V Low 7A Shutdown Current, LT4356-1 Adjustable Fault Timer Controls N-channel MOSFET Shutdown Pin Withstands -60V to 100V Fault Output Indication Guaranteed Operation to 125C Auxiliary Amplifier for Level Detection Comparator or Linear Regulator Controller Available in (4mm x 3mm) 12-Pin DFN, 10-Pin MSOP or 16-Pin SO Packages APPLICATIONS n n n n Automotive/Avionic Surge Protection Hot Swap/Live Insertion High Side Switch for Battery Powered Systems Intrinsic Safety Applications L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. The auxiliary amplifier may be used as a voltage detection comparator or as a linear regulator controller driving an external PNP pass transistor. Back-to-back FETs can be used in lieu of a Schottky diode for reverse input protection, reducing voltage drop and power loss. A shutdown pin reduces the quiescent current to less than 7A for the LT4356-1 during shutdown. The LT4356-2 differs from the LT4356-1 during shutdown by reducing the quiescent current to 60A and keeping alive the auxiliary amplifier for uses such as an undervoltage lockout or always-on regulator. TYPICAL APPLICATION 4A, 12V Overvoltage Output Regulator 10m VIN 12V IRLR2908 VOUT 80V INPUT SURGE 10 383k Overvoltage Protector Regulates Output at 27V During Transient VCC SNS GATE CTMR = 6.8F ILOAD = 500mA 102k VIN 20V/DIV OUT FB SHDN IN+ 4.99k SHDN GND EN AOUT GND TMR 12V DC-DC CONVERTER LT4356DE 100k UNDERVOLTAGE VCC FLT 4356 TA01 27V ADJUSTABLE CLAMP VOUT 20V/DIV 12V FAULT 100ms/DIV 4356 TA01b 0.1F 4356fa 1 LT4356-1/LT4356-2 ABSOLUTE MAXIMUM RATINGS (Notes 1 and 2) VCC, SHDN ................................................ -60V to 100V SNS............................. VCC - 30V or -60V to VCC + 0.3V OUT, AOUT, FLT, EN...................................... -0.3V to 80V GATE (Note 3) .................................-0.3V to VOUT + 10V FB, TMR, IN+ ................................................ -0.3V to 6V AOUT, EN, FLT, IN+...................................................-3mA Operating Temperature Range LT4356C................................................... 0C to 70C LT4356I ................................................ -40C to 85C LT4356H ............................................ -40C to 125C Storage Temperature Range DE12 .................................................. -65C to 125C MS, SO .............................................. -65C to 150C Lead Temperature (Soldering, 10 sec) MS, SO ............................................................. 300C PIN CONFIGURATION TOP VIEW TOP VIEW TMR 1 12 IN+ FB 2 11 AOUT OUT 3 GATE 4 9 EN SNS 5 8 FLT VCC 6 7 SHDN 13 10 GND DE PACKAGE 12-LEAD (4mm s 3mm) PLASTIC DFN TJMAX = 125C, JA = 43C/W EXPOSED PAD (PIN 13) PCB GND CONNECTION OPTIONAL TOP VIEW FB OUT GATE SNS VCC 1 2 3 4 5 10 9 8 7 6 MS PACKAGE 10-LEAD PLASTIC MSOP TJMAX = 125C, JA = 120C/W TMR GND EN FLT SHDN TMR 1 16 IN+ FB 2 15 NC NC 3 14 AOUT OUT 4 GATE 5 13 NC 12 GND NC 6 11 EN SNS 7 10 FLT VCC 8 9 SHDN S PACKAGE 16-LEAD PLASTIC SO TJMAX = 150C, JA = 100C/W 4356fa 2 LT4356-1/LT4356-2 ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT4356CDE-1#PBF LT4356CDE-1#TRPBF 43561 12-Lead (4mm x 3mm) Plastic DFN 0C to 70C LT4356IDE-1#PBF LT4356IDE-1#TRPBF 43561 12-Lead (4mm x 3mm) Plastic DFN -40C to 85C LT4356HDE-1#PBF LT4356HDE-1#TRPBF 43561 12-Lead (4mm x 3mm) Plastic DFN -40C to 125C LT4356CDE-2#PBF LT4356CDE-2#TRPBF 43562 12-Lead (4mm x 3mm) Plastic DFN 0C to 70C LT4356IDE-2#PBF LT4356IDE-2#TRPBF 43562 12-Lead (4mm x 3mm) Plastic DFN -40C to 85C LT4356HDE-2#PBF LT4356HDE-2#TRPBF 43562 12-Lead (4mm x 3mm) Plastic DFN -40C to 125C LT4356CMS-1#PBF LT4356CMS-1#TRPBF LTCNS 10-Lead Plastic MSOP 0C to 70C LT4356IMS-1#PBF LT4356IMS-1#TRPBF LTCNS 10-Lead Plastic MSOP -40C to 85C LT4356HMS-1#PBF LT4356HMS-1#TRPBF LTCNS 10-Lead Plastic MSOP -40C to 125C LT4356CS-1#PBF LT4356CS-1#TRPBF LT4356S-1 16-Lead Plastic SO 0C to 70C LT4356IS-1#PBF LT4356IS-1#TRPBF LT4356S-1 16-Lead Plastic SO -40C to 85C LT4356HS-1#PBF LT4356HS-1#TRPBF LT4356S-1 16-Lead Plastic SO -40C to 125C LT4356CS-2#PBF LT4356CS-2#TRPBF LT4356S-2 16-Lead Plastic SO 0C to 70C LT4356IS-2#PBF LT4356IS-2#TRPBF LT4356S-2 16-Lead Plastic SO -40C to 85C LT4356HS-2#PBF LT4356HS-2#TRPBF LT4356S-2 16-Lead Plastic SO -40C to 125C LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT4356CDE-1 LT4356CDE-1#TR 43561 12-Lead (4mm x 3mm) Plastic DFN 0C to 70C LT4356IDE-1 LT4356IDE-1#TR 43561 12-Lead (4mm x 3mm) Plastic DFN -40C to 85C LT4356HDE-1 LT4356HDE-1#TR 43561 12-Lead (4mm x 3mm) Plastic DFN -40C to 125C LT4356CDE-2 LT4356CDE-2#TR 43562 12-Lead (4mm x 3mm) Plastic DFN 0C to 70C LT4356IDE-2 LT4356IDE-2#TR 43562 12-Lead (4mm x 3mm) Plastic DFN -40C to 85C LT4356HDE-2 LT4356HDE-2#TR 43562 12-Lead (4mm x 3mm) Plastic DFN -40C to 125C LT4356CMS-1 LT4356CMS-1#TR LTCNS 10-Lead Plastic MSOP 0C to 70C LT4356IMS-1 LT4356IMS-1#TR LTCNS 10-Lead Plastic MSOP -40C to 85C LT4356HMS-1 LT4356HMS-1#TR LTCNS 10-Lead Plastic MSOP -40C to 125C LT4356CS-1 LT4356CS-1#TR LT4356S-1 16-Lead Plastic SO 0C to 70C LT4356IS-1 LT4356CS-1#TR LT4356S-1 16-Lead Plastic SO -40C to 85C LT4356HS-1 LT4356HS-1#TR LT4356S-1 16-Lead Plastic SO -40C to 125C LT4356CS-2 LT4356CS-2#TR LT4356S-2 16-Lead Plastic SO 0C to 70C LT4356IS-2 LT4356IS-2#TR LT4356S-2 16-Lead Plastic SO -40C to 85C LT4356HS-2 LT4356HS-2#TR LT4356S-2 16-Lead Plastic SO -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 4356fa 3 LT4356-1/LT4356-2 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 12V unless otherwise noted. SYMBOL PARAMETER VCC ICC Operating Voltage Range VCC Supply Current IR Reverse Input Current VGATE GATE Pin Output High Voltage IGATE(UP) GATE Pin Pull-Up Current IGATE(DN) GATE Pin Pull-Down Current VFB FB Pin Servo Voltage IFB FB Pin Input Current Overcurrent Fault Threshold VSNS ISNS ILEAK CONDITIONS MIN l V mA A A A A A A 1 2 8 16 -36 -50 1.275 1.275 1 55 55 56 56 mA mA V V A A mA mA mA V V A mV mV mV mV A A A A A A A A A l l 1 7 7 7 60 60 60 VSNS = VCC = -30V, SHDN Open VSNS = VCC = VSHDN = -30V VCC = 4V; (VGATE - VOUT) 80V VCC 8V; (VGATE - VOUT) VGATE = 12V; VCC = 12V VGATE = 48V; VCC = 48V Overvoltage, VFB = 1.4V, VGATE = 12V Overcurrent, VCC - VSNS = 120mV, VGATE = 12V Shutdown Mode, VSHDN = 0V, VGATE = 12V VGATE = 12V; VOUT = 12V, LT4356I, LT4356C VGATE = 12V; VOUT = 12V, LT4356H VFB = 1.25V l l 0.3 0.8 VSNS = (VCC - VSNS), VCC = 12V, LT4356I, LT4356C VSNS = (VCC - VSNS), VCC = 12V, LT4356H VSNS = (VCC - VSNS), VCC = 48V, LT4356I, LT4356C VSNS = (VCC - VSNS), VCC = 48V, LT4356H VSNS = VCC = 12V to 48V FLT, EN = 80V AOUT = 80V VTMR = 1V, VFB = 1.5V, (VCC - VOUT) = 0.5V VTMR = 1V, VFB = 1.5V, (VCC - VOUT) = 75V VTMR = 1.3V, VFB = 1.5V VTMR = 1V, VSNS = 60mV, (VCC - VOUT) = 0.5V VTMR = 1V, VSNS = 60mV, (VCC - VOUT) = 80V l l l l 45 42.5 46 43 -23 -30 150 10 5 1.25 1.25 0.3 50 50 51 51 l 5 10 VTMR = 1V, VFB = 1V, VSNS = 0V FLT From High to Low, VCC = 5V to 80V VGATE From Low to High, VCC = 5V to 80V From FLT going Low to GATE going Low, VCC = 5V to 80V l -1.5 -44 -3.5 -2.5 -195 1.5 -2.5 -50 -5.5 -4.5 -260 2.2 22 2.5 4.5 -4 -56 -8.5 -6.5 -315 2.7 l 1.22 0.48 80 1.25 0.5 100 1.28 0.52 120 V V mV l 1.22 1.25 0.3 200 6 0.5 1.28 1 300 14 0.7 V A A mA V 1.4 1.7 2.1 8 800 8 400 V V V mV V mV l l l l l l l l l l l 4.5 10 -4 -4.5 75 5 1.5 1.225 1.215 l VTMR TMR Pin Thresholds VTMR VIN+ IIN+ IOUT Early Warning Period IN+ Pin Input Current OUT Pin Input Current VIN+ = 1.25V VOUT = VCC = 12V VOUT = VCC = 12V, VSHDN = 0V l VOUT VSHDN OUT Pin High Threshold VOUT = VCC - VOUT; EN From Low to High VCC = 12V to 48V l 0.25 l 0.6 0.4 VOL FLT, EN Pins Output Low ISINK = 2mA ISINK = 0.1mA ISINK = 2mA ISINK = 0.1mA l l IN+ Pin Threshold AOUT Pin Output Low UNITS 80 1.5 25 30 40 70 100 250 l ITMR SHDN Pin Threshold MAX VSHDN = Float VSHDN = 0V, IN+ = 1.3V, LT4356-1 LT4356I-1, LT4356C-1 LT4356H-1 VSHDN = 0V, IN+ = 1.3V, LT4356-2 LT4356I-2, LT4356C-2 LT4356H-2 SNS Pin Input Current FLT, EN Pins Leakage Current AOUT Pin Leakage Current TMR Pin Pull-up Current TMR Pin Pull-down Current TYP 4 l l l l l l l l l l l l 2 300 2 200 4356fa 4 LT4356-1/LT4356-2 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 12V unless otherwise noted. SYMBOL PARAMETER CONDITIONS VSHDN(FLT) SHDN Pin Float Voltage SHDN Pin Current ISHDN Overcurrent Turn Off Delay Time tOFF(OC) Overvoltage Turn Off Delay Time tOFF(OV) MIN TYP MAX 0.6 -1 2.1 -8 4 V A s 1 s VCC = 12V to 48V VSHDN = 0V l GATE From High to Low, VSNS = 0 120mV l 1.2 -4 2 GATE From High to Low, VFB = 0 1.5V l 0.25 l UNITS Note 3: An internal clamp limits the GATE pin to a minimum of 10V above the OUT pin. Driving this pin to voltages beyond the clamp may damage the device. Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to GND unless otherwise specified. TYPICAL PERFORMANCE CHARACTERISTICS Specifications are at VCC = 12V, TA = 25C unless otherwise noted. ICC vs VCC ICC (Shutdown) vs VCC 1000 60 400 200 0 10 20 30 40 50 VCC (V) 60 70 80 50 100 40 80 30 40 10 20 0 0 0 10 4356 G02 20 30 40 50 VCC (V) 60 10 20 30 40 50 VCC (V) 4356 G01 60 70 80 4356 G20 ICC (Shutdown) vs Temperature 300 LT4356-1 30 LT4356-2 250 25 200 20 15 150 100 10 50 5 0 -50 0 80 70 ICC (Shutdown) vs Temperature 35 LT4356-2 IN+ = 1.3V 60 20 ICC (A) 0 LT4356-1 ICC (A) ICC (A) 600 ICC (A) ICC (A) 800 ICC (Shutdown) vs VCC 120 -25 25 75 0 50 TEMPERATURE (C) 100 125 4356 G03 0 -50 -25 25 75 0 50 TEMPERATURE (C) 100 125 4356 G21 4356fa 5 LT4356-1/LT4356-2 TYPICAL PERFORMANCE CHARACTERISTICS Specifications are at VCC = 12V, TA = 25C unless otherwise noted. SHDN Current vs Temperature 6 GATE Pull-Up Current vs Temperature GATE Pull-Up Current vs VCC VSHDN = 0V 5 40 35 35 30 30 3 25 25 IGATE (A) IGATE (A) ISHDN (A) 4 20 15 2 -25 25 75 0 50 TEMPERATURE (C) 100 0 125 0 10 20 30 4356 G04 GATE Pull-Down Current vs Temperature 220 12 200 60 160 140 120 0 50 25 75 TEMPERATURE (C) 100 10 6 4 2 -25 25 75 0 50 TEMPERATURE (C) 0 125 0 14 12 VCC = 4V 6 10 8 IGATE (A) 12 14 16 4356 G09 OVERVOLTAGE CONDITION VOUT = 5V 40 VTMR = 1V TA = -45C 10 32 TA = 25C ITMR (A) 6 4 48 TA = 130C VCC = 8V 8 2 Overvoltage TMR Current vs (VCC - VOUT) 16 VGATE (V) VGATE (V) 100 VGATE vs VCC 10 8 6 24 16 4 2 0 -50 6 4356 G08 IGATE = -1A 4 8 4 4356 G07 12 VOUT = 12V 12 8 VGATE vs Temperature 125 VGATE vs IGATE 14 OVERCURRENT CONDITION VSNS = 120mV 0 -50 125 100 4356 G06 2 -25 0 50 25 75 TEMPERATURE (C) -25 4356 G05 VGATE (V) 180 14 0 -50 80 70 10 IGATE(DOWN) (mA) IGATE(DOWN) (mA) 40 50 VCC (V) GATE Pull-Down Current vs Temperature OVERVOLTAGE CONDITION VFB = 1.5V 100 -50 15 5 5 0 -50 20 10 10 1 VGATE = VOUT = 12V -25 0 50 25 75 TEMPERATURE (C) 100 125 4356 G10 2 I GATE = -1A VOUT = VCC 0 0 10 20 8 0 30 40 50 VCC (V) 60 70 80 4356 G11 0 10 20 30 40 50 VCC - VOUT (V) 60 70 80 4356 G12 4356fa 6 LT4356-1/LT4356-2 TYPICAL PERFORMANCE CHARACTERISTICS Specifications are at VCC = 12V, TA = 25C unless otherwise noted. 3.0 14 280 OVERVOLTAGE, EARLY WARNING PERIOD 12 VFB = 1.5V VTMR = 1.3V 10 ITMR (A) 200 160 120 2.0 8 6 80 4 40 2 20 0.5 30 40 50 VCC - VOUT (V) 60 70 0 80 10 20 30 40 50 VCC (V) 60 0 -50 80 70 100 125 4356 G15 500 AOUT OVERVOLTAGE CONDITION VFB = 1.5V 400 3.0 2.5 0 25 50 75 TEMPERATURE (C) Overvoltage Turn-Off Time vs Temperature 4.0 3.5 -25 4356 G14 4356 G13 Output Low Voltage vs Current FLT 2.0 tOFF (ns) VOL (V) EN 1.5 1.0 300 200 100 0.5 0 0 0.5 2.0 1.0 1.5 CURRENT (mA) 0 -50 3.0 2.5 -25 0 25 50 75 TEMPERATURE (C) 4356 G16 125 Reverse Current vs Reverse Voltage Overcurrent Turn-Off Time vs Temperature 4.0 100 4356 G17 -20 OVERCURRENT CONDITION VSNS = 120mV VCC = SNS 3.5 -15 3.0 ICC (mA) 10 tOFF (s) 0 1.5 1.0 0 0 VTMR = 1V 2.5 ITMR (A) OVERCURRENT CONDITION VOUT = 0V 240 VTMR = 1V ITMR (A) TMR Pull-Down Current vs Temperature Warning Period TMR Current vs VCC Overcurrent TMR Current vs (VCC - VOUT) 2.5 -10 2.0 -5 1.5 1.0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 4356 G18 0 0 -20 -40 -60 -80 VCC (V) 4356 G19 4356fa 7 LT4356-1/LT4356-2 PIN FUNCTIONS AOUT (DFN and SO Packages Only): Amplifier Output. Open collector output of the auxiliary amplifier. It is capable of sinking up to 2mA from 80V. The negative input of the amplifier is internally connected to a 1.25V reference. OUT: Output Voltage Sense Input. This pin senses the voltage at the source of the N-channel MOSFET and sets the fault timer current. When the OUT pin voltage reaches 0.7V away from VCC, the EN pin goes high impedance. EN: Open-Collector Enable Output. The EN pin goes high impedance when the voltage at the OUT pin is above (VCC - 0.7V), indicating the external MOSFET is fully on. The state of the pin is latched until the OUT pin voltage resets at below 0.5V and goes back up above 2V. The internal NPN is capable of sinking up to 3mA of current from 80V to drive an LED or opto-coupler. SHDN: Shutdown Control Input. The LT4356 can be shut down to a low current mode by pulling the SHDN pin below 0.4V. Pull this pin above 2.1V or disconnect it and allow the internal current source to turn the part back on. The leakage current to ground at the pin should be limited to no more than 1A if no pull up device is used to turn the part on. The SHDN pin can be pulled up to 100V or below GND by 60V without damage. In shutdown, the auxiliary amplifier turns off in the LT4356-1 but continues operating in the LT4356-2. Exposed Pad (DFN Package Only): Exposed pad may be left open or connected to device ground (GND). FB: Voltage Regulator Feedback Input. Connect this pin to the center tap of the output resistive divider connected between the OUT pin and ground. During an overvoltage condition, the GATE pin is servoed to maintain a 1.25V threshold at the FB pin. This pin is clamped internally to 7V. Tie to GND to disable the OV clamp. FLT: Open-Collector Fault Output. This pin pulls low after the voltage at the TMR pin has reached the fault threshold of 1.25V. It indicates the pass transistor is about to turn off because either the supply voltage has stayed at an elevated level for an extended period of time (voltage fault) or the device is in an overcurrent condition (current fault). The internal NPN is capable of sinking up to 3mA of current from 80V to drive an LED or opto-coupler. GATE: N-Channel MOSFET Gate Drive Output. The GATE pin is pulled up by an internal charge pump current source and clamped to 14V above the OUT pin. Both voltage and current amplifiers control the GATE pin to regulate the output voltage and limit the current through the MOSFET. GND: Device Ground. IN+ (DFN and SO Packages Only): Positive Input of the Auxiliary Amplifier. This amplifier can be used as a level detection comparator with external hysteresis or linear regulator controlling an external PNP transistor. This pin is clamped internally to 7V. Connect to ground if unused. SNS: Current Sense Input. Connect this pin to the output of the current sense resistor. The current limit circuit controls the GATE pin to limit the sense voltage between VCC and SNS pins to 50mV. At the same time the sense amplifier also starts a current source to charge up the TMR pin. This pin can be pulled below GND by up to 60V, though the voltage difference with the VCC pin must be limited to less than 30V. Connect to VCC if unused. TMR: Fault Timer Input. Connect a capacitor between this pin and ground to set the times for early warning, fault and cool down periods. The current charging up this pin during fault conditions depends on the voltage difference between the VCC and OUT pins. When VTMR reaches 1.25V, the FLT pin pulls low to indicate the detection of a fault condition. If the condition persists, the pass transistor turns off when VTMR reaches the threshold of 1.35V. As soon as the fault condition disappears, the pull up current stops and a 2A current starts to pull the TMR pin down. When VTMR reaches the retry threshold of 0.5V, the GATE pin pulls high turning back on the pass transistor. VCC: Positive Supply Voltage Input. The positive supply input ranges from 4V to 80V for normal operation. It can also be pulled below ground potential by up to 60V during a reverse battery condition, without damaging the part. The supply current is reduced to 7A with all the functional blocks off. 4356fa 8 LT4356-1/LT4356-2 BLOCK DIAGRAM VCC GATE + - 14V CHARGE PUMP + OUT FB + 50mV SNS - VA IA 1.25V - SHDN FLT AOUT OC 1.25V AUXILIARY AMPLIFIER SHDN RESTART OUT OV EN CONTROL LOGIC GATEOFF FLT - + IN+ 1.35V - VCC + 0.5V + ITMR - + 2A 1.25V TMR - GND 4356 BD 4356fa 9 LT4356-1/LT4356-2 OPERATION Some power systems must cope with high voltage surges of short duration such as those in automobiles. Load circuitry must be protected from these transients, yet high availability systems must continue operating during these events. The potential at the TMR pin starts decreasing as soon as the overvoltage condition disappears. When the voltage at the TMR pin reaches 0.5V the GATE pin begins rising, turning on the MOSFET. The FLT pin will then go to a high impedance state. The LT4356 is an overvoltage protection regulator that drives an external N-channel MOSFET as the pass transistor. It operates from a wide supply voltage range of 4V to 80V. It can also be pulled below ground potential by up to 60V without damage. The low power supply requirement of 4V allows it to operate even during cold cranking conditions in automotive applications. The internal charge pump turns on the N-channel MOSFET to supply current to the loads with very little power loss. Two MOSFETs can be connected back to back to replace an inline Schottky diode for reverse input protection. This improves the efficiency and increases the available supply voltage level to the load circuitry during cold crank. The fault timer allows the load to continue functioning during short transient events while protecting the MOSFET from being damaged by a long period of supply overvoltage, such as a load dump in automobiles. The timer period varies with the voltage across the MOSFET. A higher voltage corresponds to a shorter fault timer period, ensuring the MOSFET operates within its safe operating area (SOA). Normally, the pass transistor is fully on, powering the loads with very little voltage drop. When the supply voltage surges too high, the voltage amplifier (VA) controls the gate of the MOSFET and regulates the voltage at the source pin to a level that is set by the external resistive divider from the OUT pin to ground and the internal 1.25V reference. A current source starts charging up the capacitor connected at the TMR pin to ground. If the voltage at the TMR pin, VTMR, reaches 1.25V, the FLT pin pulls low to indicate impending turn-off due to the overvoltage condition. The pass transistor stays on until the TMR pin reaches 1.35V, at which point the GATE pin pulls low turning off the MOSFET. The LT4356 senses an overcurrent condition by monitoring the voltage across an optional sense resistor placed between the VCC and SNS pins. An active current limit circuit (IA) controls the GATE pin to limit the sense voltage to 50mV. A current is also generated to start charging up the TMR pin. This current is about 5 times the current generated during an overvoltage event. The FLT pin pulls low when the voltage at the TMR pin reaches 1.25V and the MOSFET is turned off when it reaches 1.35V. An auxiliary amplifier is provided with the negative input connected to an internal 1.25V reference. The output pull down device is capable of sinking up to 2mA of current allowing it to drive an LED or opto coupler. This amplifier can be configured as a linear regulator controller driving an external PNP transistor or a comparator function to monitor voltages. A shutdown pin turns off the pass transistor and reduces the supply current to less than 7A for the LT4356-1. The supply current drops down to 60A while keeping the internal reference and the auxiliary amplifier active for the LT4356-2 version during shutdown. 4356fa 10 LT4356-1/LT4356-2 APPLICATIONS INFORMATION The LT4356 can limit the voltage and current to the load circuitry during supply transients or overcurrent events. The total fault timer period should be set to ride through short overvoltage transients while not causing damage to the pass transistor. The selection of this N-channel MOSFET pass transistor is critical for this application. It must stay on and provide a low impedance path from the input supply to the load during normal operation and then dissipate power during overvoltage or overcurrent conditions. The following sections describe the overcurrent and the overvoltage faults, and the selection of the timer capacitor value based on the required warning time. The selection of the N-channel MOSFET pass transistor is discussed next. Auxiliary amplifier, reverse input, and the shutdown functions are covered after the MOSFET selection. External component selection is discussed in detail in the Design Example section. Overvoltage Fault The LTC4356 limits the voltage at the OUT pin during an overvoltage situation. An internal voltage amplifier regulates the GATE pin voltage to maintain a 1.25V threshold at the FB pin. During this period of time, the power MOSFET is still on and continues to supply current to the load. This allows uninterrupted operation during short overvoltage transient events. When the voltage regulation loop is engaged for longer than the time-out period, set by the timer capacitor connected from the TMR pin to ground, an overvoltage fault is detected. The GATE pin is pulled down to the OUT pin by a 150mA current. After the fault condition has disappeared and a cool down period has transpired, the GATE pin starts to pull high again. This prevents the power MOSFET from being damaged during a long period of overvoltage, such as during load dump in automobiles. Overcurrent Fault The LT4356 features an adjustable current limit that protects against short circuits or excessive load current. During an overcurrent event, the GATE pin is regulated to limit the current sense voltage across the VCC and SNS pins to 50mV. An overcurrent fault occurs when the current limit circuitry has been engaged for longer than the time-out delay set by the timer capacitor. The GATE pin is then immediately pulled low by a 10mA current to GND turning off the MOSFET. After the fault condition has disappeared and a cool down period has transpired, the GATE pin is allowed to pull back up and turn on the pass transistor. Fault Timer The LT4356 includes an adjustable fault timer pin. Connecting a capacitor from the TMR pin to ground sets the delay timer period before the MOSFET is turned off. The same capacitor also sets the cool down period before the MOSFET is allowed to turn back on after the fault condition has disappeared. Once a fault condition, either overvoltage or overcurrent, is detected, a current source charges up the TMR pin. The current level varies depending on the voltage drop across the drain and source terminals of the power MOSFET(VDS), which is typically from the VCC pin to the OUT pin. This scheme takes better advantage of the available Safe Operating Area (SOA) of the MOSFET than would a fixed timer current. The timer function operates down to VCC = 5V across the whole temperature range. 4356fa 11 LT4356-1/LT4356-2 APPLICATIONS INFORMATION Fault Timer Current The timer current starts at around 2A with 0.5V or less of VDS, increasing linearly to 50A with 75V of VDS during an overvoltage fault (Figure 1). During an overcurrent fault, it starts at 4A with 0.5V or less of VDS but increases to 260A with 80V across the MOSFET (Figure 2). This arrangement allows the pass transistor to turn off faster during an overcurrent event, since more power is dissipated during this condition. Refer to the Typical Performance Characteristics section for the timer current at different VDS in both overvoltage and overcurrent events. When the voltage at the TMR pin, VTMR, reaches the 1.25V threshold, the FLT pin pulls low to indicate the detection of a fault condition and provide warning to the load of the impending power loss. In the case of an overvoltage fault, the timer current then switches to a fixed 5A. The interval between FLT asserting low and the MOSFET turning off is given by: t WARNING = CTMR * 100mV 5A VTMR(V) ITMR = 5A ITMR = 5A 1.35 1.25 VDS = 75V (ITMR = 50A) VDS = 10V (ITMR = 8A) 0.50 TIME tFLT = 15ms/F tWARNING = 20ms/F tFLT = 93.75ms/F tWARNING = 20ms/F TOTAL FAULT TIMER = tFLT + tWARNING 4356 F01 Figure 1. Overvoltage Fault Timer Current VTMR(V) 1.35 1.25 VDS = 80V (ITMR = 260A) 0.50 tFLT = 2.88ms/F VDS = 10V (ITMR = 35A) TIME tWARNING = 0.38ms/F tFLT = 21.43ms/F TOTAL FAULT TIMER = tFLT + tWARNING tWARNING = 2.86ms/F 4356 F02 Figure 2. Overcurrent Fault Timer Current 4356fa 12 LT4356-1/LT4356-2 APPLICATIONS INFORMATION This fixed early warning period allows the systems to perform necessary backup or house-keeping functions before the power supply is cut off. After VTMR crosses the 1.35V threshold, the pass transistor turns off immediately. Note that during an overcurrent event, the timer current is not reduced to 5A after VTMR has reached 1.25V threshold, since it would lengthen the overall fault timer period and cause more stress on the power MOSFET. As soon as the fault condition has disappeared, a 2A current starts to discharge the timer capacitor to ground. When VTMR reaches the 0.5V threshold, the internal charge pump starts to pull the GATE pin high, turning on the MOSFET. The TMR pin is then actively regulated to 0.5V until the next fault condition appears. The total cool down timer period is given by: tCOOL = CTMR * 0.85V 2A MOSFET Selection The LT4356 drives an N-channel MOSFET to conduct the load current. The important features of the MOSFET are on-resistance RDS(ON), the maximum drain-source voltage V(BR)DSS, the threshold voltage, and the SOA. The maximum allowable drain-source voltage must be higher than the supply voltage. If the output is shorted to ground or during an overvoltage event, the full supply voltage will appear across the MOSFET. The gate drive for the MOSFET is guaranteed to be more than 10V and less than 16V for those applications with VCC higher than 8V. This allows the use of standard threshold voltage N-channel MOSFETs. For systems with VCC less than 8V, a logic level MOSFET is required since the gate drive can be as low as 4.5V. The SOA of the MOSFET must encompass all fault conditions. In normal operation the pass transistor is fully on, dissipating very little power. But during either overvoltage or overcurrent faults, the GATE pin is servoed to regulate either the output voltage or the current through the MOSFET. Large current and high voltage drop across the MOSFET can coexist in these cases. The SOA curves of the MOSFET must be considered carefully along with the selection of the fault timer capacitor. Transient Stress in the MOSFET During an overvoltage event, the LT4356 drives a series pass MOSFET to regulate the output voltage at an acceptable level. The load circuitry may continue operating throughout this interval, but only at the expense of dissipation in the MOSFET pass device. MOSFET dissipation or stress is a function of the input voltage waveform, regulation voltage and load current. The MOSFET must be sized to survive this stress. Most transient event specifications use the model shown in Figure 3. The idealized waveform comprises a linear ramp of rise time tr, reaching a peak voltage of VPK and exponentially decaying back to VIN with a time constant of t. A common automotive transient specification has constants of tr = 10s, VPK = 80V and = 1ms. A surge condition known as "load dump" has constants of tr = 5ms, VPK = 60V and = 200ms. VPK VIN tr 4356 F03 Figure 3. Prototypical Transient Waveform 4356fa 13 LT4356-1/LT4356-2 APPLICATIONS INFORMATION MOSFET stress is the result of power dissipated within the device. For long duration surges of 100ms or more, stress is increasingly dominated by heat transfer; this is a matter of device packaging and mounting, and heatsink thermal mass. This is analyzed by simulation, using the MOSFET thermal model. For short duration transients of less than 100ms, MOSFET survival is increasingly a matter of safe operating area (SOA), an intrinsic property of the MOSFET. SOA quantifies the time required at any given condition of VDS and ID to raise the junction temperature of the MOSFET to its rated maximum. MOSFET SOA is expressed in units of watt-squared-seconds (P2t). This figure is essentially constant for intervals of less than 100ms for any given device type, and rises to infinity under DC operating conditions. Destruction mechanisms other than bulk die temperature distort the lines of an accurately drawn SOA graph so that P2t is not the same for all combinations of ID and VDS. In particular P2t tends to degrade as VDS approaches the maximum rating, rendering some devices useless for absorbing energy above a certain voltage. Calculating Transient Stress To select a MOSFET suitable for any given application, the SOA stress must be calculated for each input transient which shall not interrupt operation. It is then a simple matter to chose a device which has adequate SOA to survive the maximum calculated stress. P2t for a prototypical transient waveform is calculated as follows (Figure 4). Let a = VREG - VIN b = VPK - VIN (VIN = Nominal Input Voltage) Then 1 ( b - a )3 1 b P 2 t = ILOAD 2 tr + 2a 2 ln + 3a 2 + b2 - 4ab b a 2 3 VPK T VREG VIN tr 4356 F04 Figure 4. Safe Operating Area Required to Survive Prototypical Transient Waveform Typically VREG VIN and >> tr simplifying the above to P2 t = 1 2 ILOAD 2 ( VPK - VREG ) 2 (W 2s) For the transient conditions of VPK = 80V, VIN = 12V, VREG = 16V, tr = 10s and = 1ms, and a load current of 3A, P2t is 18.4W2s--easily handled by a MOSFET in a D-pak package. The P2t of other transient waveshapes is evaluated by integrating the square of MOSFET power versus time. Calculating Short-Circuit Stress SOA stress must also be calculated for short-circuit conditions. Short-circuit P2t is given by: P2t = (VIN * VSNS/RSNS)2 * tTMR (W2s) where, VSNS is the SENSE pin threshold, and tTMR is the overcurrent timer interval. For VIN = 14.7V, VSNS = 50mV, RSNS = 12m and CTMR = 100nF, P2t is 6.6W2s--less than the transient SOA calculated in the previous example. Nevertheless, to account for circuit tolerances this figure should be doubled to 13.2W2s. Limiting Inrush Current and GATE Pin Compensation The LT4356 limits the inrush current to any load capacitance by controlling the GATE pin voltage slew rate. An external capacitor can be connected from GATE to ground to slow down the inrush current further at the expense of slower turn-off time. The gate capacitor is set at: C1 = IGATE(UP) IINRUSH *CL 4356fa 14 LT4356-1/LT4356-2 APPLICATIONS INFORMATION The LTC4356 does not need extra compensation components at the GATE pin for stability during an overvoltage or overcurrent event. With transient input voltage step faster than 5V/s, a gate capacitor, C1, to ground is needed to prevent self enhancement of the N-channel MOSFET. The extra gate capacitance slows down the turn off time during fault conditions and may allow excessive current during an output short event. An extra resistor, R1, in series with the gate capacitor can improve the turn off time. A diode, D1, should be placed across R1 with the cathode connected to C1 as shown in Figure 5. Q1 RLIM *4.7 2N2905A OR BCP53 INPUT 2.5V OUTPUT 150mA MAX 10F R6 100k * OPTIONAL FOR CURRENT LIMIT D1* BAV99 VOUT 1.25 11 R4 249k AOUT LT4356S 47nF 12 IN+ ILIM z R4 R5 R5 0.7 RLIM R5 249k 4356 F06 Figure 6. Auxiliary LDO Output with Optional Current Limit Reverse Input Protection D1 IN4148W R3 R1 C1 GATE LT4356S 4356 F05 Figure 5 Auxiliary Amplifier An uncommitted amplifier is included in the LT4356 to provide flexibility in the system design. With the negative input connected internally to the 1.25V reference, the amplifier can be connected as a level detect comparator with external hysteresis. The open collector output pin, AOUT, is capable of driving an opto or LED. It can also interface with the system via a pull-up resistor to a supply voltage up to 80V. Another use is to implement undervoltage lockout, as shown in the typical application "Overvoltage Regulator with Undervoltage Lockout." In shutdown, the auxiliary amplifier turns off in the LT4356-1 but continues operating in the LT4356-2. The amplifier can also be configured as a low dropout linear regulator controller. With an external PNP transistor, such as 2N2905A, it can supply up to 100mA of current with only a few hundred mV of dropout voltage. Current limit can be easily included by adding two diodes and one resistor (Figure 6). A blocking diode is commonly employed when reverse input potential is possible, such as in automotive applications. This diode causes extra power loss, generates heat, and reduces the available supply voltage range. During cold crank, the extra voltage drop across the diode is particularly undesirable. The LT4356 is designed to withstand reverse voltage without damage to itself or the load. The VCC, SNS, and SHDN pins can withstand up to 60V of DC voltage below the GND potential. Back-to-back MOSFETs must be used to eliminate the current path through their body diodes (Figure 7). Figure 8 shows the approach with a P-Channel MOSFET in place of Q2. RSNS 10m VIN 12V Q2 IRLR2908 D2* SMAJ58CA Q3 2N3904 D1 1N4148 6 Q1 IRLR2908 R4 R5 10 1M VOUT 12V, 3A CLAMPED AT 16V R3 10 R1 59k R7 10k 5 SNS 4 GATE VCC 3 OUT FB 2 R2 4.99k LT4356S 7 11 12 SHDN FLT AOUT IN+ GND 10 *DIODES INC. EN TMR 1 8 9 4356 F07 CTMR 0.1F Figure 7. Overvoltage Regulator with N-channel MOSFET Reverse Input Protection 4356fa 15 LT4356-1/LT4356-2 APPLICATIONS INFORMATION RSNS 10m VIN 12V Q2 Si4435 Q1 IRLR2908 VOUT 12V, 3A CLAMPED AT 16V D1 1N5245 15V D2* SMAJ58CA R3 10 R6 10k 5 SNS 6 4 GATE R1 59k 3 OUT VCC FB 2 R2 4.99k 7 11 12 LT4356S SHDN FLT AOUT IN+ GND 10 *DIODES INC. EN TMR 1 8 9 4356 F08 CTMR 0.1F Figure 8. Overvoltage Regulator with P-Channel MOSFET Reverse Input Protection Shutdown The LT4356 can be shut down to a low current mode when the voltage at the SHDN pin goes below the shutdown threshold of 0.6V. The quiescent current drops to 7A for the LT4356-1 and 60A for the LT4356-2 which leaves the auxiliary amplifier on. The SHDN pin can be pulled up to VCC or below GND by up to 60V without damaging the pin. Leaving the pin open allows an internal current source to pull it up and turn on the part while clamping the pin to 2.5V. The leakage current at the pin should be limited to no more than 1A if no pull up device is used to help turn it on. A total bulk capacitance of at least 22F low ESR electrolytic is required close to the source pin of MOSFET Q1. In addition, the bulk capacitance should be at least 10 times larger than the total ceramic bypassing capacitor on the input of the DC/DC converter. RSNS 10m VIN CL* 22F D2 SMAJ58A 6 Supply Transient Protection The LT4356 is guaranteed to be safe from damage with supply voltages up to 100V. Nevertheless, voltage transients above 100V may cause permanent damage. During a short-circuit condition, the large change in current flowing through power supply traces and associated wiring can cause inductive voltage transients which could exceed 100V. To minimize the voltage transients, the power trace parasitic inductance should be minimized by using wide traces. A small surge suppressor, D2, in Figure 9, at the input will clamp the voltage spikes. Q1 IRLR2908 R4 383k 7 12 VCC R3 10 5 4 3 SNS GATE OUT FB UNDERVOLTAGE 2 SHDN IN+ R2 4.99k LT4356S R5 100k EN 11 R1 59k AOUT GND 10 TMR 1 FLT 9 8 VCC DC-DC CONVERTER SHDN GND FAULT 4356 F09 CTMR 47nF *SANYO 25CE22GA Figure 9. Overvoltage Regulator with Low-Battery Detection 4356fa 16 LT4356-1/LT4356-2 APPLICATIONS INFORMATION Layout Considerations Next calculate the sense resistor, RSNS, value: To achieve accurate current sensing, Kelvin connection to the current sense resistor (RSNS in Figure 9) is recommended. The minimum trace width for 1oz copper foil is 0.02" per amp to ensure the trace stays at a reasonable temperature. 0.03" per amp or wider is recommended. Note that 1oz copper exhibits a sheet resistance of about 530/square. Small resistances can cause large errors in high current applications. Noise immunity will be improved significantly by locating resistive dividers close to the pins with short VCC and GND traces. RSNS = CTMR is then chosen for 1ms of early warning time: CTMR = First, calculate the resistive divider value to limit VOUT to 16V during an overvoltage event: VREG = 1.25V * (R1 + R2) = 16V R2 Set the current through R1 and R2 during the overvoltage condition to 250A. R2 = 1.25V = 5k 250A Finally, calculate R4 and R5 for the 6V low battery threshold detection: (16V - 1.25V ) * R2 1.25V 6V = 1.25V * (R4 + R5) R5 Choose 100k for R5. R4 = (6V - 1.25V ) * R5 1.25V = 380k Select 383k for R4. The pass transistor, Q1, should be chosen to withstand the output short condition with VCC = 14V. The total overcurrent fault time is: tOC = 47nF * 0.85V = 0.878ms 45.5A The power dissipation on Q1 equals to: Choose 4.99k for R2. R1 = 1ms * 5A = 50nF 100mV The closest standard value for CTMR is 47nF. Design Example As a design example, take an application with the following specifications: VCC = 8V to 14V DC with transient up to 80V, VOUT 16V, current limit (ILIM) at 5A, low battery detection at 6V, and 1ms of overvoltage early warning (Figure 9). 50mV 50mV = = 10m ILIM 5A P= = 58.88k The closest standard value for R1 is 59k. 14V * 50mV = 70W 10m These conditions are well within the Safe Operating Area of IRLR2908. 4356fa 17 LT4356-1/LT4356-2 TYPICAL APPLICATIONS Wide Input Range 5V to 28V Hot Swap with Undervoltage Lockout RSNS 20m Q1 SUD50N03-10 VOUT VIN 100F R6 118k R3 10 C1 47nF SNS VCC GATE OUT SHDN FB AOUT IN+ LT4356DE-1 R7 49.9k FLT GND EN TMR 4356 TA02 CTMR 1F 24V Overvoltage Regulator Withstands 150V at VIN VIN 24V Q1 IRF640 R9 1k 1W VOUT CLAMPED AT 32V R3 10 5 SNS 6 4 GATE VCC FB D2* SMAT70A 2 R2 4.99k 7 SHDN 8 FLT 9 LT4356DE EN GND 10 *DIODES INC. R1 118k 3 OUT TMR 1 4356 TA03 CTMR 0.1F 4356fa 18 LT4356-1/LT4356-2 TYPICAL APPLICATIONS Overvoltage Regulator with Undervoltage Lockout RSNS 20m Q1 IRLR2908 VOUT CLAMPED AT 16V VIN D2* SMAJ58A R6 280k R4 1M R3 10 VCC R5 1M SNS GATE R1 59k OUT SHDN FB R2 4.99k AOUT IN+ UV RISING = 5.04V LT4356DE-2 R7 100k FLT GND *DIODES INC. EN TMR 4356 TA04 CTMR 0.1F Overvoltage Regulator with Low Battery Detection and Output Keep Alive During Shutdown 1k 0.5W RSNS 10m VIN 12V D2* SMAJ58A Q1 IRLR2908 R3 10 R4 402k 6 12 R5 105k 7 *DIODES INC. 5 SNS 4 GATE VOUT 12V, 4A CLAMPED AT 16V Q2 VN2222 3 OUT VCC FB LT4356DE AOUT SHDN FLT 10 2 R2 VDD 24.9k R6 47k IN+ GND R1 294k D1 1N4746A 18V 1W EN TMR 1 11 LBO 8 9 4356 TA05 CTMR 0.1F 4356fa 19 LT4356-1/LT4356-2 TYPICAL APPLICATIONS 2.5A, 48V Hot Swap with Overvoltage Output Regulation at 72V and UV Shutdown at 35V RSNS 15m VIN 48V Q1 FDB3632 D2* SMAT70A R4 140k R3 10 VOUT 48V 2.5A R6 100k CL 300F C1 6.8nF 6 VCC D1 1N4714 BV = 33V 7 5 4 SNS GATE 3 OUT 12 IN+ SHDN R5 4.02k R8 47k LT4356DE 8 R7 1M FB R1 226k 2 R2 4.02k FLT 9 EN GND *DIODES INC. AOUT TMR 10 1 11 PWRGD 4356 TA06 CTMR 0.1F 2.5A, 28V Hot Swap with Overvoltage Output Regulation at 36V and UV Shutdown at 15V RSNS 15m VIN 28V Q1 FDB3632 D2* SMAT70A R4 113k R3 10 VOUT 28V 2.5A R6 27k CL 300F C1 6.8nF D1 1N4700 BV = 13V 7 6 VCC 5 4 SNS GATE 3 OUT 12 IN+ SHDN R5 4.02k R8 47k LT4356DE 8 9 *DIODES INC. FB 2 R1 110k R2 4.02k FLT EN R7 1M GND 10 TMR 1 AOUT 11 PWRGD 4356 TA07 CTMR 0.1F 4356fa 20 LT4356-1/LT4356-2 TYPICAL APPLICATIONS Overvoltage Regulator with Reverse Input Protection Up to -80V RSNS 10m Q2 IRLR2908 VIN 12V Q3 2N3904 D2* R4 SMAJ58CA 10 R5 1M 6 D1 1N4148 Q1 IRLR2908 5 SNS VCC R7 10k VOUT 12V, 3A CLAMPED AT 16V R3 10 4 GATE 3 OUT FB 2 R1 59k R2 4.99k D3** IN4148 LT4356DE 7 11 12 SHDN FLT AOUT IN+ * DIODES INC. ** OPTIONAL COMPONENT FOR REDUCED STANDBY CURRENT GND 10 EN TMR 1 8 9 4356 TA08 CTMR 0.1F 4356fa 21 LT4356-1/LT4356-2 PACKAGE DESCRIPTION DE/UE Package 12-Lead Plastic DFN (4mm x 3mm) (Reference LTC DWG # 05-08-1695 Rev D) 0.70 0.05 3.60 0.05 2.20 0.05 3.30 0.05 1.70 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC 2.50 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 4.00 0.10 (2 SIDES) 7 R = 0.115 TYP 0.40 0.10 12 R = 0.05 TYP PIN 1 TOP MARK (NOTE 6) 0.200 REF 3.30 0.10 3.00 0.10 (2 SIDES) 1.70 0.10 0.75 0.05 6 0.25 0.05 PIN 1 NOTCH R = 0.20 OR 0.35 x 45 CHAMFER 1 (UE12/DE12) DFN 0806 REV D 0.50 BSC 2.50 REF 0.00 - 0.05 BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE A VARIATION OF VERSION (WGED) IN JEDEC PACKAGE OUTLINE M0-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 4356fa 22 LT4356-1/LT4356-2 PACKAGE DESCRIPTION MS Package 10-Lead Plastic MSOP (Reference LTC DWG # 05-08-1661) 0.889 0.127 (.035 .005) 5.23 (.206) MIN 3.20 - 3.45 (.126 - .136) 3.00 0.102 (.118 .004) (NOTE 3) 0.50 0.305 0.038 (.0197) (.0120 .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 10 9 8 7 6 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) DETAIL "A" 0.497 0.076 (.0196 .003) REF 0 - 6 TYP GAUGE PLANE 1 2 3 4 5 0.53 0.152 (.021 .006) DETAIL "A" 1.10 (.043) MAX 0.86 (.034) REF 0.18 (.007) SEATING PLANE 0.17 - 0.27 (.007 - .011) TYP 0.50 (.0197) NOTE: BSC 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.1016 0.0508 (.004 .002) MSOP (MS) 0307 REV E 4356fa 23 LT4356-1/LT4356-2 PACKAGE DESCRIPTION S Package 16-Lead Plastic Small Outline (Narrow .150 Inch) (Reference LTC DWG # 05-08-1610) .386 - .394 (9.804 - 10.008) NOTE 3 .045 p.005 .050 BSC 16 N 15 14 13 12 11 10 9 N .245 MIN .160 p.005 .150 - .157 (3.810 - 3.988) NOTE 3 .228 - .244 (5.791 - 6.197) 1 .030 p.005 TYP 2 3 N/2 N/2 RECOMMENDED SOLDER PAD LAYOUT 1 .010 - .020 s 45o (0.254 - 0.508) .008 - .010 (0.203 - 0.254) 2 3 4 5 .053 - .069 (1.346 - 1.752) NOTE: 1. DIMENSIONS IN .014 - .019 (0.355 - 0.483) TYP 7 8 .004 - .010 (0.101 - 0.254) 0o - 8o TYP .016 - .050 (0.406 - 1.270) 6 .050 (1.270) BSC S16 0502 INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) 4356fa 24 LT4356-1/LT4356-2 REVISION HISTORY (Revision history begins at Rev A) REV DATE DESCRIPTION PAGE NUMBER A 05/10 Revised Features and Description Added parameters to VOL and updated Max value for VSHDN(FLT) in the Electrical Characteristics section Revised Pin Functions section 1 4, 5 8 Replaced Figure 6 and made text edits in the Operation and Applications Information sections 10-17 Updated drawings in the Typical Applications section 19, 21 4356fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 25 LT4356-1/LT4356-2 TYPICAL APPLICATION Overvoltage Regulator with Linear Regulator Up to 100mA Q2 2N2905A 2.5V, 100mA RSNS 10m VIN 12V Q1 IRLR2908 D2* SMAJ58A 6 VOUT 12V, 3A CLAMPED AT 16V R3 10 4 GATE 5 SNS R6 100k C5 10F R1 59k 3 OUT VCC FB 2 R2 4.99k 11 7 LT4356DE AOUT 12 IN+ SHDN FLT *DIODES INC. GND 10 EN TMR 1 8 R4 249k C3 47nF R5 249k 9 4356 TA09 CTMR 0.1F RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1641-1/LT1641-2 Positive High Voltage Hot SwapTM Controllers Active Current Limiting, Supplies From 9V to 80V LTC1696 Overvoltage Protection Controller ThinSOTTM Package, 2.7V to 28V LTC1735 High Efficiency Synchronous Step-Down Switching Regulator Output Fault Protection, 16-Pin SSOP LTC1778 No RSENSETM Wide Input Range Synchronous Step-Down Controller Up to 97% Efficiency, 4V VIN 36V, 0.8V VOUT (0.9)(VIN), IOUT Up to 20A LTC2909 Triple/Dual Inputs UV/OV Negative Monitor Pin Selectable Input Polarity Allows Negative and OV Monitoring LTC2912/LTC2913 Single/Dual UV/OV Voltage Monitor Ads UV and OV Trip Values, 1.5% Threshold Accuracy LTC2914 Quad UV/OV Monitor For Positive and Negative Supplies LTC3727/LTC3727-1 2-Phase, Dual, Synchronous Controller 4V VIN 36V, 0.8V VOUT 14V LTC3827/LTC3827-1 Low IQ, Dual, Synchronous Controller 4V VIN 36V, 0.8V VOUT 10V, 80A Quiescent Current LTC3835/LTC3835-1 Low IQ, Synchronous Step-Down Controller LT3845 Low IQ, Synchronous Step-Down Controller Single Channel LTC3827/LTC3827-1 LT3850 Dual, 550kHz, 2-Phase Sychronous Step-Down Controller Dual 180 Phased Controllers, VIN 4V to 24V, 97% Duty Cycle, 4mm x 4mm QFN-28, SSOP-28 Packages LT4256 Positive 48V Hot Swap Controller with Open-Circuit Detect Foldback Current Limiting, Open-Circuit and Overcurrent Fault Output, Up to 80V Supply LTC4260 Positive High Voltage Hot Swap Controller with ADC and I2C Wide Operating Range 8.5V to 80V LTC4352 Ideal MOSFET ORing Diode External N-channel MOSFETs Replace ORing Diodes, 0V to 18V Operation LTC4354 Negative Voltage Diode-OR Controller Controls Two N-channel MOSFETs, 1s Turn-Off, 80V Operation LTC4355 Positive Voltage Diode-OR Controller Controls Two N-channel MOSFETs, 0.5s Turn-Off, 80V Operation 4V VIN 60V, 1.23V VOUT 36V, 120A Quiescent Current Hot Swap, No RSENSE and ThinSOT are trademarks of Linear Technology Corporation. 4356fa 26 Linear Technology Corporation LT 0510 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2009