1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com
6
Resistor Type Thick Film, Epoxy Molded
Power Rating 2W at 70°C
3W at 25°C
Resistance Range Metal Glaze:1.5KΩ to 5MΩ
Metal Oxide:15Ω to <1.5KΩ
Tolerance 1%, 2%, 5%
Temp. Coeff.
Resistance
Metal Glaze: 100/200ppm
Metal Oxide: 350ppm
Not all tolerances and TCR values available
throughout entire resistance range
Construction Metal glaze 100/200 ppm
Metal oxide 350 ppm
Max. Working
Voltage
RCWV or 1000 V whichever lesser. (RCWV
= rated DC or RMS AC continuos working
voltage at commercial line frequency and
waveform (volt) )
Diel. Width-
standing Volt.
1000 VRMS
Terminals Copper Wire, Solder Coated axial, RoHS
composition
Oper. Temp. -55º to +155ºC
MOX500 Series
Epoxy Molded, Metal Glaze-Metal Oxide Resistors
FEATURES
•MeetsMil-Std-202
•MeetsIEC61000-4-5upto2KV
•MoldedConstruction
•AvailableinE96values
DIMENSIONS
in./mm
CHARACTERISTICS
1.430" ±.075 /
36.3mm ±1.9
0.570" max. /
14.5mm
0.205" ±.010 /
5.2mm ±.3
0.032" ±.002 /
0.8mm ±.05
*Total resistor length
including leads approx. 70mm
for taped & reeled units
100
Percent Rated Power
Ambient Temperature,
2W
3W
°C
60
20
0
80
40
500 100 1557025-55
Derating Single Impulse Test Surge Immunity Test
Characteristic Test Method ΔR limits
Moisture
Resistance
MIL-STD-202, Method 106G ±0.20%
Humidity MIL-STD-202, Method 103, Condition B ±0.25%
Shock MIL-STD-202, Method 213, Condition I ±0.10%
Vibration MIL-STD-202, Method 204, Condition D ±0.10%
Terminal
Strength
MIL-STD-202, Method 211A, Condition
A or B
±0.10%
Short Term
Overload
DC test potential 2.5 time the rated con-
tinuous working voltage but not exceed-
ing twice the maximum voltage specified
±0.5%
Load Life 1000 hrs at RCWV duty cycle 1.5hr ON,
0.5 hr OFF at 70ºC ±2ºC
±2%
Temperature
Cycling
-65º to +125ºC ±0.10%
Resistance to
soldering heat
Temp 350ºC ±10ºC for 3 ±0.5 sec ±1%
Surge
Immunity
IEC61000-4-5, waveform 1.2/50μS, 10
Pulses applied. Does not include values
under 1KΩ.
<±1%
Power (watts)
Pulse duration
10
100,000
100
1,000
10,000
1µs 10µs 100µs 1ms 1s10ms 100ms
Peak Voltage (V)
Resistance (Ω)
500
5,000
1K 10K 100K 1M
Change in resistance under 1% Resistors are tested in accordance with
IEC61000-4-5, waveform 1.2/50μS, 10 Pulses
applied. Limit of acceptance is a shift in resis-
tance of less then 1% from the initial value. Graph
data shows values equal or greather than 1KΩ.
1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com 7
MOX500 Series
Epoxy Molded, Metal Glaze-Metal Oxide Resistors
TAPE & REEL
EIA-296standard
ORDERING INFORMATION
MOX5001001FSETR
Resistor
Series
Tape & reel
TR = 1250 pcs
Tolerance
F = 1%
G = 2%
J = 5%
Ohms
First 3 digits are
significant; 4th
digit is multiplier
(# of zeros to follow).
examples:
10R0 = 10 ohms
1001 = 1000 ohms
1502 = 15000 ohms
TCR
S = 100ppm/°C
L = 200ppm/°C
K = 350ppm/°C
RoHS
compliant
Standard part numbers for MOX500 Series
Resistance 2% tolerance 5% tolerance
100 MOX500100RJSE
150 MOX500150RJSE
270 MOX500270RJSE
1K MOX5001001JSE
1.5K MOX5001501JSE
2.7K MOX5002701GSE
3.3K MOX5003301JSE
4.3K MOX5004301JSE
6.8K MOX5006801JSE
7.5K MOX5007501GSE
10K MOX5001002JSE
15K MOX5001502JSE
18K MOX5001802JSE
20K MOX5002002GSE
27K MOX5002702GSE
33K MOX5003302JSE
47K MOX5004702GSE
66K MOX5006602JSE
100K MOX5001003GSE
150K MOX5001503GSE
220K MOX5002203GSE
270K MOX5002703GSE
330K MOX5003303GSE
1M MOX5001004GSE
2.82" max.
14"
ø 1.13"
2.88"
6mm ±1
56.5mm ±1.5
L1L2
L1 – L2 = 1.4mm max.
0.80mm
max.
10mm ±0.5
rev 10/17-1