MOX500 Series Epoxy Molded, Metal Glaze-Metal Oxide Resistors F e at u r e s * Meets Mil-Std-202 * Meets IEC 61000-4-5 up to 2KV * Molded Construction * Available in E96 values C h a r a c t e r i s t i cs Resistor Type Thick Film, Epoxy Molded Characteristic Test Method Power Rating 2W at 70C 3W at 25C Resistance Range Metal Glaze:1.5K to 5M Metal Oxide:15 to <1.5K Humidity MIL-STD-202, Method 103, Condition B Shock MIL-STD-202, Method 213, Condition I Tolerance 1%, 2%, 5% Temp. Coeff. Metal Glaze: 100/200ppm Resistance Metal Oxide: 350ppm Not all tolerances and TCR values available throughout entire resistance range Construction Metal glaze Metal oxide 100/200 ppm 350 ppm Max. Working RCWV or 1000 V whichever lesser. (RCWV Voltage = rated DC or RMS AC continuos working voltage at commercial line frequency and waveform (volt) ) Diel. Width- 1000 VRMS standing Volt. 20 0 -55 Short Term DC test potential 2.5 time the rated conOverload tinuous working voltage but not exceeding twice the maximum voltage specified 0.5% 0 25 50 70 100 Ambient Temperature, C 155 Surge IEC61000-4-5, waveform 1.2/50S, 10 Immunity Pulses applied. Does not include values under 1K. 1% <1% Surge Immunity Test 5,000 1,000 100 10s 100s 1ms 10ms 100ms Pulse duration 500 1K 1s Change in resistance under 1% 1.430" .075 / 36.3mm 1.9 0.570" max. / 14.5mm *Total resistor length including leads approx. 70mm for taped & reeled units 10K 100K Resistance () 1M Resistors are tested in accordance with IEC61000-4-5, waveform 1.2/50S, 10 Pulses applied. Limit of acceptance is a shift in resistance of less then 1% from the initial value. Graph data shows values equal or greather than 1K. Dimensions in./mm 6 0.10% Resistance to Temp 350C 10C for 3 0.5 sec soldering heat 10,000 10 1s 2% Peak Voltage (V) 3W Power (watts) Percent Rated Power 2W 60 40 0.10% 100,000 80 0.10% Terminal MIL-STD-202, Method 211A, Condition Strength A or B Single Impulse Test 100 0.25% 0.10% Temperature -65 to +125C Cycling Oper. Temp. -55 to +155C 0.20% Vibration MIL-STD-202, Method 204, Condition D Load Life 1000 hrs at RCWV duty cycle 1.5hr ON, 0.5 hr OFF at 70C 2C Terminals Copper Wire, Solder Coated axial, RoHS composition Derating R limits Moisture MIL-STD-202, Method 106G Resistance 0.032" .002 / 0.8mm .05 0.205" .010 / 5.2mm .3 1-866-9-OHMITE * Int'l 1-847-258-0300 * Fax 1-847-574-7522 * www.ohmite.com * info@ohmite.com MOX500 Series Epoxy Molded, Metal Glaze-Metal Oxide Resistors Ta p e & R e e l EIA-296 standard 56.5mm 1.5 6mm 1 14" 2.82" max. 2.88" 10mm 0.5 o 1.13" 0.80mm max. L1 L2 L1 - L2 = 1.4mm max. O R D ERIN G IN F O R M ATI O N Tolerance F = 1% G = 2% RoHS J = 5% compliant MOX5001001FSETR Resistor Series Ohms TCR First 3 digits are S = 100ppm/C significant; 4th L = 200ppm/C K = 350ppm/C digit is multiplier (# of zeros to follow). examples: 10R0 = 10 ohms 1001 = 1000 ohms 1502 = 15000 ohms Tape & reel TR = 1250 pcs Standard part numbers for MOX500 Series Resistance 2% tolerance 5% tolerance 100 150 270 1K 1.5K 2.7K MOX5002701GSE 3.3K 4.3K 6.8K 7.5K MOX5007501GSE 10K 15K 18K 20K MOX5002002GSE 27K MOX5002702GSE 33K 47K MOX5004702GSE 66K 100K MOX5001003GSE 150K MOX5001503GSE 220K 270K 330K 1M MOX5002203GSE MOX5002703GSE MOX5003303GSE MOX5001004GSE rev 10/17-1 1-866-9-OHMITE * Int'l 1-847-258-0300 * Fax 1-847-574-7522 * www.ohmite.com * info@ohmite.com 7 MOX500100RJSE MOX500150RJSE MOX500270RJSE MOX5001001JSE MOX5001501JSE MOX5003301JSE MOX5004301JSE MOX5006801JSE MOX5001002JSE MOX5001502JSE MOX5001802JSE MOX5003302JSE MOX5006602JSE