AURORA, IL. 60505 CONNOR-WINFIELD CORPORATION PHONE (630) 851-4722 FAX (630) 851-5040 HCMOS SURFACE MOUNT TRI-STATE OSCILLATORS SPECIFICATIONS HSM516 HSM526 HSM536 HSM546 Frequency Range 1.8MHz to 80MHz +25ppm +50ppm +100ppm +20ppm Frequency Stability (Inclusive of calibration tolerance at 25C, operating temperature range, input voltage change, load change, aging, shock and vibration) Temperature Range O;Cc to +70C Waveform HCMOS Squarewave Load SOpF Voltage Voh 4.5V Minimum Vol 0.5V Maximum Output Current loh 16mA lol 16mA Duty Cycle 45/55% Maximum Rise/Fall Time SnS Maximum Output E/D Time 100nS Maximum Enable Vih 2.2V Minimum Inout lih 400uA Maximum , 30uUA Typical npu Disable Vil 0.8V Maximum lil 400uA Maximum , SOuUA Typical Oscillator output is enabled with no connection on pin 1 Start Up Time 10mS Maximum Supply Voltage +5Vde +10% Supply Current 80mA Maximum PIN CONNECTION r 252 .104 .200 (6.35mm) ~Gsrmn) | sem 1 ENABLE /DISABLE 4 3 ! 2 GROUND | ) (2.54mi) 3 OUTPUT T_ 4 VDD 433 Dimensional reer men) (11.05mm) { ORDERING INFORMATION e .098 HSM516 50.00MHz | (2.54mm) vu | fo 1 2 | CLOCK CENTER .004 .043 TYP (4) SERIES FREQUENCY (.10mm) (1.14mm) see as . . . Specifications subject to change without notice BULLETIN #: __SMOO3 _ REV: oo PAGE 1 OF 2 pate: 8/6/01 _ ISSUED BY: CONNOR-WINFIELD CORPORATION AURORA, IL. 60505 PHONE (630) 851-4722 FAX (630) 8515040 OUTPUT WAVEFORM TF - --Tr "1" LEVEL +4.5Vdc \ 90% Vcc +2.5Vdc 50% Vcc +0.5Vdc \ | \ 0.0Vdc "Oo" LEVEL SYMMETRY TEST CIRCUIT OSCILLOSCOPE PROBE FREQ COUNTER 3 2 INPUT FOR E/D MECHANICAL CHARACTERISTICS FREE DROP: The specimen shall meet electrical characteristics after tested 3 times Free Drop testing on the hard wooden board from a height of 75cm. VIBRATION: The specimen shall meet electrical characteristics after tested by the following conditions; 10-55Hz 1.5mm Amplitude, 55-2000Hz 20Gs, 2 hours for each plane. THERMAL SHOCK: After applied Thermal Shock of 260 C max x 10 sec max x 2 times, or 230 C max x 180 sec max, the specimen shall meet electrical characteristics. SOLDERABILITY: (EIAJRCX0102/101 Condition 1a) . Flux: MIL-F14256 (WW Rosin=25%, Isopropyl alcohol=75%) Solder: QQ-S571 (Sn=63%, Pb=37%) Solder bath temperature: 235 C +/-5 C. Depth of immersion: Up to electrical terminal. immersing time: Within 2 sec +/0.5 sec into solder ath. After performing the above procedures, a newly soldered coverage shall be greater than 90%. PUN > ENVIRONMENTAL CHARACTERISTICS TEMPERATURE CYCLE: The specimen shall meet electrical characteristics after tested 5 cycles of 55 C/30 min & +125 C/30 min. HERMETICAL No bubbles gppear in Flourinert (FC43) at 125 C +/5 C, for 5 minutes, SOLVENT RESISTANCE: Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene. SOLDERING GENERAL CONDITIONS: 260C max x 10 sec max x 2 times max or 230C max x 180 sec max x 1 time. TYPICAL OPERATION DATA (Vapor phase reflow) 20 to 100 sec up to 215C, 50 sec at 215C then down to room temperature per 1 to 5C/sec DIMENSIONS 08 08 45 ae 1 . . fos 8.45 DIA | y we -| .200 |-= 7 Le f boot, pp= 138 a TYP a | 7 Lo] qf 15 475 | . .065 ry { TYP] [> | Cby -| O [E/D GROUND 47 To | el\..06 DA} { ul } |.135/- 0 Bypass capacitor, Cby, should be 2 ceramic capacitor > .O1uf. 45 | 07 Specifications subject to change MEETS EIA481A AND EIAJ1009B . without notice 1,000 PCS/REEL .95 =] BULLETIN #: _ SMOO3 _ REV: UW PAGE 2) OF 2) DATE: _ 8/6/01 _ ISSUED BY: