PART TEMP RANGE MAX TEMPCO
(ppm/°C)
INITIAL ERROR
(mV) PIN-PACKAGE
REF01EP 0°C to +70°C 8.5 ±30 8 Plastic DIP
REF01HP 0°C to +70°C 25 ±50 8 Plastic DIP
REF01HSA 0°C to +70°C 25 ±50 8 SO
REF01CP 0°C to +70°C 65 ±100 8 Plastic DIP
REF01CSA 0°C to +70°C 65 ±100 8 SO
REF01CESA -40°C to +85°C 65 ±100 8 SO
REF02EP 0°C to +70°C 8.5 ±15 8 Plastic DIP
REF02HP 0°C to +70°C 25 ±25 8 Plastic DIP
REF02HSA 0°C to +70°C 25 ±25 8 SO
REF02CP 0°C to +70°C 65 ±50 8 Plastic DIP
REF02CSA 0°C to +70°C 65 ±50 8 SO
REF02CESA -40°C to +85°C 65 ±50 8 SO
General Description
The REF01/REF02 are industry-standard precision volt-
age references. The stable 10V output of the REF01
can be adjusted over a ±3% range with minimal effect
on temperature stability, while the 5V output REF02 can
be adjusted over a ±6% range. The 10V REF01 has a
single-supply operation over an input voltage range of
13V to 33V, while the 5V REF02 has a single-supply
operation over an input voltage range of 7V to 33V.
Both devices offer a low-current drain of 1mA. The
REF02 also provides a TEMP pin whose output voltage
varies linearly with temperature, making this device
suitable for a wide variety of temperature-sensing and
control applications. For new designs, refer to the
MAX6035 or MAX6143 data sheets.
Features
Pretrimmed to +5V, +10V ±0.3%
Excellent Temperature Stability: 3ppm/°C
Low Noise: 10µVP-P (REF02)
Low Supply Current: 1.4mA (max)
Short-Circuit Protected
Linear Temperature Transducer Output (REF02)
REF01/REF02
+5V, +10V Precision
Voltage References
________________________________________________________________ Maxim Integrated Products 1
Ordering Information
REF01
REF02
OUTPUT
RP
10k
6
5
TRIM
VO
VIN
+15V
4
GND
REFERENCE WITH TRIMMED OUTPUT.
2
Typical Operating Circuit
19-0887; Rev 5; 7/04
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Ordering Information continued at end of data sheet.
Applications
Analog-to-Digitial Converters
Digitial-to-Analog Converters
Digital Voltmeters
Voltage Regulators
Threshold Detectors
REF01/REF02
+5V, +10V Precision
Voltage References
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS–REF01
ELECTRICAL CHARACTERISTICS—REF01/REF01A/REF01E/REF01H
(V
IN
= +15V, T
A
= +25°C, unless otherwise noted.)
ELECTRICAL CHARACTERISTICS
—REF01/REF01A/REF01E/REF01H
(VIN = +15V, -55°C TA+125°C for REF01A and REF01, 0°C TA+70°C for REF01E and REF01H, IL= 0mA, unless otherwise
noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Input Voltage
REF01, A, E, H.....................................................................40V
REF01C ...............................................................................30V
Continuous Power Dissipation
T099 (J) (derate at 7.1mW°C above +80°C).................500mW
CERDIP (2) (derate at 6.7mW/°C above +75°C) .........500mW
Plastic Dip (P) (derate at 5.6mW/°C above +36°C) .....500mW
Small Outline (S) (derate at 5.0mW/°C above +55°C) ..300mW
Output Short-Circuit Duration
(to ground or VIN) .......................................................Indefinite
Storage Temperature Range .............................-65°C to +150°C
Operating Temperature Range
REF01A, REF01 ..............................................-55°C to +125°C
REF01E, REF01H, REF01C
(except REF01CESA)...........................................0°C to +70°C
REF01CESA......................................................-40°C to +85°C
Lead Temperature (soldering, 60s) .................................+300°C
REF01A/REF01E REF01/REF01H
PARAMETER SYMBOL CONDITIONS
MIN TYP MAX MIN TYP MAX
UNITS
Output Voltage VOIL = 0 9.97 10.00 10.03 9.95 10.00 10.05 V
Output Adjustment Range Vtrim RP = 10k±3.0 ±3.3 ±3.0 ±3.3 %
Output Voltage Noise enP-P 0.1Hz to 10Hz (Note 1) 20 30 20 30 µVP-P
Line Regulation VIN = 13V to 33V (Note 2) 0.006 0.010 0.006 0.010 %/V
Load Regulation IL = 0 to 10mA (Note 2) 0.005 0.008 0.006 0.010 %/mA
Turn-On Settling Time tON To ±0.1% of final value 400 400 µs
Quiescent Supply Current ISY No load 1.0 1.4 1.0 1.4 mA
Load Current IL
To specified output
voltage tolerance 10 21 10 21 mA
Sink Current IS
To specified output
voltage tolerance 0.3 0.5 0.3 0.5 mA
Short-Circuit Current ISC VO = 0V 30 30 mA
REF01A/REF01E REF01/REF01H
PARAMETER SYMBOL CONDITIONS
MIN TYP MAX MIN TYP MAX
UNITS
0°C TA +70°C 0.02 0.06 0.07 0.17
Output Voltage Change with
Temperature (Note 3) VOT -55°C TA +125°C 0.06 0.15 0.18 0.45 %
Output Voltage Temperature
Coefficient TCVO(Note 4) 3 8.5 10.0 25.0 ppm/°C
Change in VO Temperature
Coefficient with Output
Adjustment
RP = 10k0.7 0.7 ppm/%
0°C TA +70°C 0.007 0.012 0.007 0.012
Line Regulation
(VIN = 13V to 33V) (Note 2) -55°C TA +125°C 0.009 0.015 0.009 0.015 %/V
0°C TA +70°C 0.006 0.010 0.007 0.012
Load Regulation
(IL = 0 to 8mA) (Note 2) -55°C TA +125°C 0.007 0.012 0.009 0.015 %/mA
Note 1: Guaranteed by design for REF01EP, REF01HP, REF01HSA, REF01CP, REF01CSA, REF01CESA. Sample tested for all other
grades and packages.
Note 2: Line and load regulation specifications include the effect of self heating. REF01EP, REF01HP, REF01HSA, REF01CP, REF01CSA,
REF01CESA are 100% production tested at TA= +25°C and guaranteed by design for TA= TMIN to TMAX, as specified.
Note 3: VOT is defined as the absolute difference between the maximum output voltage and the minimum output voltage over the
specified temperature range expressed as a percentage of 10V. REF01CP, REF01CSA, REF01CESA, REF01HSA guaranteed
by design.
Note 4: TCVOis defined as VOT divided by the temperature range. REF01CP, REF01CSA, REF01CESA, REF01HSA guaranteed by
design.
VOT =
×
V-V
10V 100
MAX MIN
REF01/REF02
+5V, +10V Precision
Voltage References
_______________________________________________________________________________________ 3
ELECTRICAL CHARACTERISTICS—REF01C
(VIN = +15V, TA= +25°C, IL= 0mA, unless otherwise noted.)
REF01C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Output Voltage VOIL = 0mA 9.90 10.00 10.10 V
Output Adjustment Range Vtrim RP = 10k±2.7 ±3.3 %
Output Voltage Noise enP-P 0.1Hz to 10Hz (Note 1) 25 35 µVP-P
Line Regulation VIN = 13V to 30V (Note 2) 0.009 0.015 %/V
IL = 0 to 8mA 0.006 0.015
Load Regulation (Note 2)
IL = 0 to 4mA 0.006 0.015
%/mA
Turn-On Settling Time tON To ±0.1% of final value 400 µs
Quiescent Supply Current ISY No load 1.0 1.6 mA
Load Current ILTo specified output voltage tolerance 8 21 mA
Sink Current ISTo specified output voltage tolerance 0.2 0.5 mA
Short-Circuit Current ISC VO = 0V 30 mA
ELECTRICAL CHARACTERISTICS—REF01C
(VIN = +15V, TA= TMIN to TMAX, unless otherwise noted.)
REF01C
PARAMETER SYMBOL CONDITIONS
MIN TYP MAX
UNITS
Output Voltage Change with
Temperature VOT (Note 3) 0.14 0.45 %
Output Voltage Temperature
Coefficient TCVO(Note 4) 20 65 ppm/°C
Change in VO Temperature
Coefficient with Output Adjustment RP = 10k0.7 ppm/%
Line Regulation VIN = 13V to 30V (Note 2) 0.011 0.018 %/V
Load Regulation IL = 0 to 5mA (Note 2) 0.008 0.018 %/mA
Output Adjustment
The REF01 trim terminal can be used to adjust the volt-
age over a 10V ±300mV range. This feature allows the
system designer to trim system errors by setting the ref-
erence to a voltage other than 10V, including 10.240V for
binary applications (see the Typical Operating Circuit).
Adjustment of the output does not significantly affect the
temperature performance of the device. The tempera-
ture coefficient change is approximately 0.7ppm/°C for
100mV of output adjustment.
REF01/REF02
+5V, +10V Precision
Voltage References
4 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS–REF02
Input Voltage
REF02, A, E, H.....................................................................40V
REF02C, D...........................................................................30V
Continuous Power Dissipation
T099 (J) (derate at 7.1mW°C above +80°C).................500mW
CERDIP (2) (derate at 6.7mW/°C above +75°C) .........500mW
Plastic Dip (P) (derate at 5.6mW/°C above +36°C) .....500mW
Small Outline (S) (derate at 5.0mW/°C above +55°C) ..300mW
Storage Temperature Range .............................-65°C to +150°C
Operating Temperature Range
REF02A, REF02 ..............................................-55°C to +125°C
REF02E, REF02H .................................................0°C to +70°C
REF02C (except REF02CESA), REF02D .............0°C to +70°C
REF02CESA......................................................-40°C to +85°C
Output Short-Circuit Duration
(to ground or VIN) .......................................................Indefinite
Lead Temperature (soldering, 60s) .................................+300°C
ELECTRICAL CHARACTERISTICS—REF02/REF02A/REF02E/REF02H
(VIN = +15V, -55°C TA+125°C for REF02A and REF02, 0°C TA+70°C for REF02E and REF02H, IL= 0mA, unless otherwise
noted.)
ELECTRICAL CHARACTERISTICS—REF02/REF02A/REF02E/REF02H
(VIN = +15V, TA= +25°C, unless otherwise noted.)
REF02A/REF02E REF02/REF02H
PARAMETER SYMBOL CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
Output Voltage VOIL = 0 4.985 5.000 5.015 4.975 5.000 5.025 V
Output Adjustment Range Vtrim RP = 10k±3 ±6 ±3 ±6 %
Output Voltage Noise enP-P 0.1Hz to 10Hz (Note 5) 10 15 10 15 µVP-P
Line Regulation VIN = 8V to 33V (Note 6) 0.006 0.010 0.006 0.010 %/V
Load Regulation IL = 0 to 10mA (Note 6) 0.005 0.010 0.006 0.010 %/mA
Turn-On Settling Time tON To ±0.1% of final value 230 230 µs
Quiescent Supply Current ISY No load 1.0 1.4 1.0 1.4 mA
Load Current ILTo specified output voltage tolerance 10 21 10 21 mA
Sink Current ISTo specified output voltage tolerance 0.3 0.5 0.3 0.5 mA
Short-Circuit Current ISC VO = 0V 30 30 mA
Temperature Voltage
Output VT(Note 7) 630 630 mV
REF02A/REF02E REF02/REF02H
PARAMETER SYMBOL CONDITIONS
MIN TYP MAX MIN TYP MAX
UNITS
0°C TA +70°C 0.02 0.06 0.07 0.17
Output Voltage Change with
Temperature (Note 8) VOT -55°C TA +125°C 0.06 0.15 0.18 0.45
%
Output Voltage Temperature
Coefficient TCVO(Note 9) 3 8.5 10 25 ppm/°C
Change in VO Temperature
Coefficient with Output
Adjustment
RP = 10k0.7 0.7 ppm/%
0°C TA +70°C 0.007 0.012 0.007 0.012
Line Regulation
(V
I N
= 8V to 33V) (Note 6) -55°C TA +125°C 0.009 0.015 0.009 0.015 %/V
0°C TA +70°C 0.006 0.010 0.007 0.012
Load Regulation
(IL = 0 to 8mA) (Note 6) -55°C TA +125°C 0.007 0.012 0.009 0.015
%/mA
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
REF01/REF02
+5V, +10V Precision
Voltage References
_______________________________________________________________________________________ 5
ELECTRICAL CHARACTERISTICS—REF02/REF02A/REF02E/REF02H (continued)
(VIN = +15V, -55°C TA+125°C for REF02A and REF02, 0°C TA+70°C for REF02E and REF02H, IL= 0mA, unless otherwise
noted.)
REF02A/REF02E REF02/REF02H
PARAMETER SYMBOL CONDITIONS
MIN TYP MAX MIN TYP MAX
UNITS
Temperature Voltage Output
Temperature Coefficient TCVT(Note 7) 2.1 2.1 mV/°C
ELECTRICAL CHARACTERISTICS—REF02C/REF02D
(VIN = +15V, TA= +25°C, unless otherwise noted.)
REF02C REF02D
PARAMETER SYMBOL CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
Output Voltage VOIL = 0mA 4.950 5.000 5.050 4.900 5.000 5.100 V
Output Adjustment Range Vtrim RP = 10k±2.7 ±6.0 ±2.0 ±6.0 %
Output Voltage Noise enP-P 0.1Hz to 10Hz
(Note 5) 12 18 12 µVP-P
Line Regulation VIN = 8V to 30V (Note 6) 0.009 0.015 0.010 0.04 %/V
IL = 0 to 8mA 0.006 0.015
Load Regulation (Note 6) IL = 0 to 4mA 0.015 0.04 %/mA
Turn-On Settling Time tON To ±0.1% of final value 230 230 µs
Quiescent Supply Current ISY No load 1.0 1.6 1.0 2.0 mA
Load Current ILTo specified output
voltage tolerance 8 21 8 21 mA
Sink Current ISTo specified output
voltage tolerance 0.2 0.5 0.2 0.5 mA
Short-Circuit Current ISC VO = 0V 30 30 mA
Temperature Voltage Output VT(Note 7) 630 630 mV
ELECTRICAL CHARACTERISTICS—REF02C/REF02D
(VIN = +15V, TA= TMIN to TMAX, IL= 0mA, unless otherwise noted.)
REF02C REF02D
PARAMETER SYMBOL CONDITIONS
MIN TYP MAX MIN TYP MAX
UNITS
Output Voltage Change with
Temperature VOT (Note 8) 0.14 0.45 0.49 1.7 %
Output Voltage Temperature
Coefficient TCVO(Note 9) 20 65 70 250 ppm/°C
Change in VO Temperature
Coefficient with Output
Adjustment
RP = 10k0.7 0.7 ppm/%
Line Regulation VIN = 8V to 30V (Note 6) 0.011 0.018 0.012 0.05 %/V
Load Regulation IL = 0 to 5mA (Note 6) 0.008 0.018 0.016 0.05 %/mA
Temperature Voltage Output
Temperature Coefficient TCVT(Note 7) 2.1 2.1 mV/°C
REF01/REF02
+5V, +10V Precision
Voltage References
6 _______________________________________________________________________________________
Output Adjustment
The REF02 trim terminal can be used to adjust the out-
put voltage over a 5V ±300mV range. This feature
allows the system designer to trim system errors by set-
ting the reference to a voltage other than 5V (refer to
the Typical Operating Circuit).
Adjustment of the output does not significantly affect
the temperature performance of the device. Typically,
the temperature coefficient change is 0.7ppm/°C for
100mV of output adjustment.
Temperature Voltage Output
The REF02 provides a temperature-dependent output
voltage on the TEMP pin. This voltage is proportional to
the absolute temperature, and has a scale factor of
approximately 2.1mV/°C (Figure 1).
Output Voltage = 2.1(T + 273)mV
where T = Temperature in °C.
430
530
480
630
580
680
730
830
780
880
-60 -40 -20 0 20 40 60 80 100 120 140
TEMPERATURE (°C)
TEMP VOLTAGE OUTPUT (mV)
Figure 1. REF02 Temperature/Voltage Output vs. Temperature
ELECTRICAL CHARACTERISTICS–REF02 (continued)
(VIN = +15V, TA= TMIN to TMAX, IL= 0mA, unless otherwise noted.)
Note 5: Guaranteed by design for REF02EP, REF02HP, REF02HSA, REF02CP, REF02CSA, REF02CESA. Sample tested for all
other grades and packages.
Note 6: Line and load regulation specifications include the effect of self heating. REF02EP, REF02HP, REF02HSA, REF02CP, REF02CSA,
REF02CESA are 100% production tested at TA= +25°C and guaranteed by design for TA= TMIN to TMAX, as specified.
Note 7: Limit current in or out of pin 3 to 50nA and capacitance on pin 3 to 30pF.
Note 8: VOT is defined as the absolute difference between the maximum output voltage and the minimum output voltage over the
specified temperature range expressed as a percentage of 5V. REF02CP, REF02CSA, REF02CESA, REF02HSA guaranteed
by design.
Note 9: TCVOis defined as VOT divided by the temperature range. REF02CP, REF02CSA, REF02CESA, REF02HSA guaranteed by
design.
VOT =
×
V-V
5V 100
MAX MIN
REF01/REF02
+5V, +10V Precision
Voltage References
_______________________________________________________________________________________ 7
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
6
26
16
46
36
66
56
76
10 1k100 10k 100k 1M
LINE REGULATION
vs. FREQUENCY
REF01/02 TOC01
FREQUENCY (Hz)
LINE REGULATION (dB)
VIN = 15V
TA = +25°C
10
100
1000
10,000
10 1k100 10k 100k 1M
REF01 OUTPUT WIDEBAND
NOISE vs. BANDWIDTH
(0.1Hz TO FREQUENCY INDICATED)
REF01/02 TOC02
FREQUENCY (Hz)
OUTPUT NOISE (µVP-P)
VIN = 15V
TA = +25°C
10
100
1000
10,000
10 1k100 10k 100k 1M
REF02 OUTPUT WIDEBAND
NOISE vs. BANDWIDTH
(0.1Hz TO FREQUENCY INDICATED)
REF01/02 TOC03
FREQUENCY (Hz)
OUTPUT NOISE (µVP-P)
VIN = 15V
TA = +25°C
0
15
10
5
25
20
30
35
10 15 20 25 30
MAXIMUM LOAD CURRENT
vs. INPUT VOLTAGE
REF01/02 TOC04
INPUT VOLTAGE (V)
MAXIMUM LOAD CURRENT (mA)
500mW MAXIMUM
DISSIPATION
SHORT-CIRCUIT
PROTECTION
TA = +25°C
0.6
0.8
0.7
1.0
0.9
1.3
1.2
1.1
1.4
-60 200-20-40 60 8040 100 120 140
NORMALIZED LOAD
REGULATION (IL = 10mA)
vs. TEMPERATURE
REF01/02 TOC05
TEMPERATURE (°C)
LOAD REG (T)/LOAD REG (+25°C)
VIN = 15V
0.6
0.8
0.7
1.0
0.9
1.3
1.2
1.1
1.4
-60 200-20-40 60 8040 100 120 140
NORMALIZED LINE REGULATION
vs. TEMPERATURE
REF01/02 TOC06
TEMPERATURE (°C)
LOAD REG (T)/LOAD REG (+25°C)
0
5
15
10
25
20
30
-60 200-20-40 60 8040 100 120 140
MAXIMUM LOAD CURRENT
vs. TEMPERATURE
REF01/02 TOC07
TEMPERATURE (°C)
MAXIMUM LOAD CURRENT (mA)
VIN = 15V
0.7
0.8
1.0
0.9
1.2
1.1
1.3
-60 200-20-40 60 8040 100 120 140
QUIESCENT CURRENT
vs. TEMPERATURE
REF01/02 TOC08
TEMPERATURE (°C)
QUIESCENT CURRENT (mA)
VIN = 15V
0
0.010
0.005
0.015
0.030
0.025
0.020
0.035
-10 3020100506040
OUTPUT CHANGE DUE TO
THERMAL SHOCK
REF01/02 TOC09
TIME (s)
PERCENT CHANGE OUTPUT VOLTAGE (%)
VIN = 15V
TA =
+25°C
TA =
+75°C
DEVICE IMMERSED
IN +75°C OIL BATH
REF01/REF02
+5V, +10V Precision
Voltage References
8 _______________________________________________________________________________________
Typical Applications
100k
6
5
9V
9V
-
+
TRIM 10.000V
VO
VIN
1.1mA
4
GND
2
REF01
5k
10k
+10V
-10V
10k
6
5
TRIM
VO
VIN
+15V
+15V
-15V
4
GND
2
OP-07
REF01
Figure 2. Precision Calibration Standard Figure 3. ±10V Reference
R
6
53 TRIM
VO
VIN
+15V
4
IOUT
GND
2
IOUT = + 1mA
5.0V
R
REF02
*
50k
200k
1.5k
9.09k
VREF
VOUT
(10mV/°C)
6
5
TRIM
TEMP
VO
VIN
1.5k
±5%
4
*UP TO 10 FEET OF SHIELDED
4-CONDUCTOR CABLE.
GND
2
3
27
4
6
5.11k
+15V
-15V
OP-07
REF02
Figure 4. Current Source Figure 5. Precision Temperature Transducer with
Remote Sensor
REF01/REF02
+5V, +10V Precision
Voltage References
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 _____________________ 9
© 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
Ordering Information (continued)
PART TEMP RANGE MAX TEMPCO INITIAL ERROR PIN-PACKAGE
REF01AJ* -55°C to +125°C 8.5 ±30 8 TO-99
REF01AZ* -55°C to +125°C 8.5 ±15 8 Hermetic DIP
REF01CJ* 0°C to +70°C 65 ±100 8 TO-99
REF01CP-2* 0°C to +70°C 65 ±100 8 Plastic DIP
REF01CZ* 0°C to +70°C 65 ±100 8 CERDIP
REF01EJ* 0°C to +70°C 8.5 ±30 8 TO-99
REF01EZ* 0°C to +70°C 8.5 ±30 8 CERDIP
REF01HF* 0°C to +70°C 25 ±50 8 TO-99
REF01HZ* 0°C to +70°C 25 ±50 8 Hermetic DIP
REF01J* -55°C to +125°C 25 ±50 8 TO-99
REF01Z* -55°C to +125°C 25 ±50 8 CERDIP
REF02AJ* -55°C to +125°C 8.5 ±15 8 TO-99
REF02AZ* -55°C to +125°C 8.5 ±15 8 Hermetic DIP
REF02CJ* 0°C to +70°C 65 ±50 8 TO-99
REF02CZ* 0°C to +70°C 65 ±50 8 CERDIP
REF02DJ* 0°C to +70°C 25 ±100 8 TO-99
REF02DP* 0°C to +70°C 25 ±100 8 Plastic DIP
REF02DSA* 0°C to +70°C 25 ±100 8 SO
REF02EJ* 0°C to +70°C 8.5 ±15 8 TO-99
REF02EZ* 0°C to +70°C 8.5 ±15 8 CERDIP
REF02HJ* 0°C to +70°C 25 ±25 8 TO-99
REF02HZ* 0°C to +70°C 25 ±25 8 Hermetic DIP
REF02J* -55°C to +125°C 25 ±25 8 TO-99
REF02Z* -55°C to +125°C 25 ±25 8 CERDIP
TOP VIEW
VOUT
VIN
TRIM
N.C.
N.C./TEMP*
N.C.
N.C.
GROUND
(CASE)
62
8
4
5
1 7
3
REF01/
REF02 VOUT
TRIMGND
1
2
8
7
N.C.
N.C.VIN
N.C./TEMP*
N.C.
DIP
TO-99 METAL CAN
3
4
6
5
REF01/
REF02 VOUT
TRIMGDN
1
2
8
7
N.C.
N.C.VIN
N.C./TEMP*
N.C.
SO
3
4
6
5
REF01/
REF02
Pin Configurations
*NOTE: PIN 3 IS N.C. (NO CONNECTION) ON REF01, TEMP OUTPUT ON REF02.
*Not recommended for new designs. Contact factory for availability.
Package Information
For the latest package outline information, go to
www.maxim-ic.com/packages.