(R) INA2132 INA 213 2 Dual, Low Power, Single-Supply DIFFERENCE AMPLIFIER FEATURES APPLICATIONS DESIGNED FOR LOW COST LOW QUIESCENT CURRENT: 160A per Amplifier WIDE POWER SUPPLY RANGE: Single Supply: 2.7V to 36V Dual Supplies: 1.35V to 18V LOW GAIN ERROR: 0.05% max LOW NONLINEARITY: 0.001% max HIGH CMRR: 90dB HIGHLY VERSATILE CIRCUIT EASY TO USE SO-14 PACKAGE DIFFERENTIAL INPUT AMPLIFIER INSTRUMENTATION AMPLIFIER BUILDING BLOCK UNITY-GAIN INVERTING AMPLIFIER G = 1/2 AMPLIFIER G = 2 AMPLIFIER SUMMING AMPLIFIER DIFFERENTIAL CURRENT RECEIVER VOLTAGE-CONTROLLED CURRENT SOURCE BATTERY-POWERED SYSTEMS GROUND LOOP ELIMINATOR V+ DESCRIPTION 11 The INA2132 is a dual low power, unity-gain difference amplifier offering excellent value at very low cost. Each channel consists of a precision op amp with a laser-trimmed precision resistor network, providing accurate gain and high common-mode rejection. Excellent TCR tracking of the resistors maintains gain accuracy and common-mode rejection over temperature. The internal op amp's common-mode range extends to the negative supply--ideal for single-supply applications. The difference amplifier is the foundation of many commonly used circuits. The INA2132 provides this circuit function without using an expensive precision resistor network. The INA2132 is available in the SO-14 surface-mount package and is specified for operation over the extended industrial temperature range, -40C to +85C. A single version of this product with similar specifications is also available. See the INA132 data sheet for details. -In A 2 40k 40k 13 A +In A -In B 3 6 40k 40k 40k 40k 5 40k 14 10 9 B +In B 12 40k 8 Sense A Out A Ref A Sense B Out B Ref B INA2132 4 V- International Airport Industrial Park * Mailing Address: PO Box 11400, Tucson, AZ 85734 * Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 * Tel: (520) 746-1111 Twx: 910-952-1111 * Internet: http://www.burr-brown.com/ * Cable: BBRCORP * Telex: 066-6491 * FAX: (520) 889-1510 * Immediate Product Info: (800) 548-6132 (c)1998 Burr-Brown Corporation SBOS108 PDS-1488A Printed in U.S.A. December, 1998 SPECIFICATIONS: VS = 15V At TA = +25C, RL = 10k connected to ground, and reference pins connected to ground unless otherwise noted. INA2132U PARAMETER CONDITIONS VOLTAGE(1) OFFSET Initial vs Temperature vs Power Supply vs Time Channel Separation(2) MIN INA2132UA TYP MAX 75 1 5 0.3 0.04 250 5 30 MIN TYP MAX UNITS 500 10 V V/C V/V V/mo V/V RTO VOS dVOS /dT PSRR VS = 1.35V to 18V dc INPUT IMPEDANCE(3) Differential Common-Mode INPUT VOLTAGE RANGE Common-Mode Voltage Range(4) Common-Mode Rejection Ratio CMRR OUTPUT VOLTAGE NOISE(5) f = 0.1Hz to 10Hz f = 1kHz VO = 0V VCM = -30V to 28V, RS = 0 2 (V-) 80 74 1.6 65 1 0.01 1 0.0001 VO = -14V to 13.5V VO = -14V to 13.5V OUTPUT Voltage, Positive Negative Positive Negative Current Limit, per Amplifier Capacitive Load (stable operation) RL = 100k to Ground RL = 100k to Ground RL = 10k to Ground RL = 10k to Ground Continuous to Common V dB Vp-p nV/Hz -3dB 0.05 10 0.001 (V+) -1 (V+) -0.8 (V-) +0.5 (V-) +0.15 (V+) -1.5 (V+) -0.8 (V-) +1 (V-) +0.25 12 10 300 0.1 85 88 7 SR VO = 10V Step VO = 10V Step 50% Overdrive POWER SUPPLY Rated Voltage VS Voltage Range Quiescent Current (per amplifier) IQ TEMPERATURE RANGE Specification Operation Storage Thermal Resistance 2 (V+) -2 90 k k RTO GAIN Initial Error vs Temperature Nonlinearity FREQUENCY RESPONSE Small-Signal Bandwidth Slew Rate Settling Time: 0.1% 0.01% Overload Recovery Time 80 40 15 1.35 160 IO = 0mA -40 -55 -55 JA 100 0.1 0.002 V V V V mA nF kHz V/s s s s 18 185 +85 +125 +125 V/V % ppm/C % of FS V V A C C C C/W Specifications the same as INA2132U. NOTES: (1) Includes effects of amplifier's input bias and offset currents. (2) Measured output offset change of one channel for a full-scale swing (VO = -14V to 13.5V) on the opposite channel. (3) 40k resistors are ratio matched but have 20% absolute value. (4) 2 (V-) -VREF < VCM < 2 ((V+) -1) -VREF. For more detail, see Applications Information section. (5) Includes effects of amplifier's input current noise and thermal noise contribution of resistor network. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. (R) INA2132 2 SPECIFICATIONS: VS = +5V Single Supply At TA = +25C, RL = 10k connected to VS /2, and reference pin connected to VS /2, unless otherwise noted. INA2132U PARAMETER OFFSET VOLTAGE(1) Initial vs Temperature CONDITIONS RTO MIN VOS dVOS /dT INPUT VOLTAGE RANGE Common-Mode Voltage Range(2) Common-Mode Rejection CMRR OUTPUT Voltage, Positive Negative Positive Negative POWER SUPPLY Rated Voltage Voltage Range Quiescent Current INA2132UA TYP MAX 150 2 500 MIN TYP MAX UNITS 750 V V/C VCM = -2.5V to +5.5V, RS = 0 -2.5 80 90 74 V dB RL = 100k to Ground RL = 100k to Ground RL = 10k to Ground RL = 10k to Ground (V+) -1 +0.25 (V+) -1 +0.25 (V+) -0.75 +0.06 (V+) -0.8 +0.12 V V V V +5.5 +5 VS +2.7 155 IO = 0mA IQ +36 185 V V A Specifications the same as INA2132U. NOTE: (1) Includes effects of amplifier's input bias and offset currents. (2) 2 (V-) -VREF < VCM < 2 ((V+) -1) -VREF. For more detail, see Applications Information section. PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS Top View SO-14 NC 1 -In A 2 14 Ref A 13 Out A Supply Voltage, V+ to V- .................................................................... 36V Input Voltage Range .......................................................................... 80V Output Short-Circuit (to ground) .............................................. Continuous Operating Temperature .................................................. -55C to +125C Storage Temperature ..................................................... -55C to +125C Junction Temperature .................................................................... +150C Lead Temperature (soldering, 10s) ............................................... +300C A +In A 3 12 Sense A V- 4 11 V+ +In B 5 10 Sense B ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. B -In B 6 9 Out B NC 7 8 Ref B ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NC = No Connection PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER(1) INA2132U " INA2132UA " SO-14 Surface-Mount " SO-14 Surface-Mount " 235 " 235 " SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(2) TRANSPORT MEDIA -40C to +85C " -40C to +85C " INA2132U " INA2132UA " INA2132U INA2132U/2K5 INA2132UA INA2132UA/2K5 Rails Tape and Reel Rails Tape and Reel NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of "INA2132U/2K5" will get a single 2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book. (R) 3 INA2132 TYPICAL PERFORMANCE CURVES At TA = +25C and VS = 15V, unless otherwise noted. COMMON-MODE REJECTION vs FREQUENCY GAIN vs FREQUENCY 100 20 CL = 100pF RL = 10k 0 CL = 1000pF RL = -20 90 Common-Mode Rejection (dB) Closed-Loop Gain (dB) VS = 15V or +5V -40 VS = 15V 80 VS = +5V 70 60 50 40 -60 30 10k 100k 1M 10 100 1k Frequency (Hz) POWER SUPPLY REJECTION vs FREQUENCY 1M 150 +PSRR 140 VS = 15V 100 80 Channel Separation (dB) Power Supply Rejection (dB) 100k CHANNEL SEPARATION vs FREQUENCY 120 VS = +5V 60 -PSRR 40 10k Frequency (Hz) 20 130 120 110 100 90 80 70 60 0 100 1k 10k 100k 50 1M 0.1 1 10 100 Frequency (Hz) V+ 25C (V+) -1.5 (V+) -2 -40C (V+) -2.5 (V-) +2.5 -55C -40C 85C 25C (V-) +1 1M 13 200 -55C Quiescent Current (A) Output Voltage Swing (V) 85C (V+) -1 (V-) +2 100k 210 125C (V-) +1.5 10k QUIESCENT and SHORT-CIRCUIT CURRENT vs TEMPERATURE OUTPUT VOLTAGE SWING vs OUTPUT CURRENT (V+) -0.5 1k Frequency (Hz) 125C 12 ISC 190 11 180 10 IQ 170 9 160 8 (V-) +0.5 150 V- 2 0 4 6 8 10 -75 -25 0 25 50 Temperature (C) Output Current (mA) (R) INA2132 -50 4 75 100 7 125 Short-Circuit Current |mA| 10 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25C and VS = 15V, unless otherwise noted. SMALL-SIGNAL STEP RESPONSE CL = 200pF SLEW RATE vs TEMPERATURE 0.18 0.14 50mV/div Slew Rate (V/s) 0.16 0.12 0.10 0.08 0.06 -75 -50 -25 0 25 50 75 100 10s/div 125 Temperature (C) SMALL-SIGNAL STEP RESPONSE CL = 1000pF 5V/div 50mV/div LARGE-SIGNAL STEP RESPONSE 10s/div 100s/div SETTLING TIME vs LOAD CAPACITANCE INPUT COMMON-MODE VOLTAGE RANGE vs OUTPUT VOLTAGE 100 40 10V Step Common-Mode Voltage (V) Settling Time (s) 96 92 0.01% 88 84 0.1% 80 100pF VS = 15V 30 20 VS = +5V 10 0 -10 VS = 5V -20 VREF = 0V G=1 -30 -40 1000pF 10,000pF -16 Load Capacitance -12 -8 -4 0 4 8 12 16 Output Voltage (V) (R) 5 INA2132 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25C and VS = 15V, unless otherwise noted. 0.1Hz to 10Hz PEAK-TO-PEAK VOLTAGE NOISE OFFSET VOLTAGE PRODUCTION DISTRIBUTION 25 0.5V/div Percent of Amplifiers (%) VS = 15V 20 15 10 5 500 400 300 200 100 0 -100 -200 -300 -500 -400 0 500ms/div Offset Voltage (V) OFFSET VOLTAGE PRODUCTION DISTRIBUTION OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 18 VS = 15V 35 Percent of Amplifiers (%) 14 12 10 8 6 4 30 25 20 15 10 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 700 600 500 400 300 200 0 100 -100 -200 -300 0 -400 0 -500 5 -600 2 -700 Percent of Amplifiers (%) 16 40 VS = +5V Offset Voltage Drift (V/C) Offset Voltage (V) (R) INA2132 6 APPLICATIONS INFORMATION In the case where VREF is grounded, the equation simplifies to: Figure 1 shows the basic connections required for operation of the INA2132. Power supply bypass capacitors should be connected close to the device pins. 2 * (V-) < VCM < 2 * ((V+) - 1) For more information, see the typical performance curve titled "Input Common-Mode Voltage Range vs Output Voltage." The differential input signal is connected to pins 2 and 3 (or pins 6 and 5) as shown. The source impedances connected to the inputs must be nearly equal to assure good commonmode rejection. An 8 mismatch in source impedance will degrade the common-mode rejection of a typical device to approximately 80dB. Gain accuracy will also be slightly affected. If the source has a known impedance mismatch, an additional resistor in series with one input can be used to preserve good common-mode rejection. OPERATING VOLTAGE The INA2132 operates from single (+2.7V to +36V) or dual (1.35V to 18V) supplies with excellent performance. Specifications are production tested with +5V and 15V supplies. Most behavior remains unchanged throughout the full operating voltage range. Parameters which vary significantly with operating voltage are shown in the Typical Performance Curves. Do not interchange pins 3 and 14 (or pins 5 and 8) or pins 2 and 12 (or pins 6 and 10), even though nominal resistor values are equal. These resistors are laser-trimmed for precise resistor ratios to achieve accurate gain and highest CMRR. Interchanging these pins may not provide specified performance. As shown in Figure 1, sense line should be connected as close to the load as possible. The INA2132 can accurately measure differential signals that are beyond the power supply rails. Linear commonmode range extends to twice the negative power supply voltage and nearly twice the positive power supply voltage. Output phase reversal does not occur when the inputs to the internal operational amplifier are overloaded to either rail. See typical performance curve, "Common-Mode Range vs Output Voltage." NOTE: Pin numbers in parentheses ( ) refer to channel B. OFFSET VOLTAGE TRIM V+ V- 1F 1F The INA2132 is laser-trimmed for low offset voltage and drift. Most applications require no external offset adjustment. Figure 2 shows an optional circuit for trimming the output offset voltage. The output is referred to the output reference terminal (pin 14 or pin 8), which is normally grounded. A voltage applied to the Ref terminal will be summed with the output signal. This can be used to null offset voltage. The source impedance of a signal applied to the Ref terminal should be less than 8 to maintain good common-mode rejection. To assure low impedance at the Ref terminal, the trim voltage can be buffered with an op amp, such as the OPA277. 11 4 INA2132 V2 V3 2(6) 3 (5) R1 R2 40k 40k 12 (10) 13 (9) R3 RL 40k R4 40k VOUT = V3 - V2 Ref 14 (8) INA2132 2 (6) V2 FIGURE 1. Basic Power Supply and Signal Connections. R2 R1 12 (10) 13 (9) To ensure valid operation of the differential amplifier, please note the following points: 8 V3 1) VOUT = V3 - V2 + VREF 2) VOUT must be within the specified linear range. For example, with 15V supplies and a 100k load, the output will be defined by: 3 (5) VO R3 R4 +15V VO = V3 - V2 Offset Adjustment Range = 500V (V-) + 0.15V < VOUT < (V+) - 0.8V 3) Input common-mode range at the nodes of the op amp must be V- VCM (V+) - 1. To ensure that the inputs to the differential amp (+In and -In) meet this criteria, limit the common-mode voltage inputs to: 14 (8) Ref R = 237k 100k 8 -15V NOTE: For 750V range, R = 158k. 2 * (V-) - VREF < VCM < 2 * ((V+) - 1) - VREF FIGURE 2. Offset Adjustment. (R) 7 INA2132 CAPACITIVE LOAD DRIVE CAPABILITY directly adjacent on the top and bottom sides of a circuit board. Stray coupling then produces a common-mode signal which is rejected by the INA2132's input. The INA2132 can drive large capacitive loads, even at low supplies. It is stable with a 10nF load. Refer to the "SmallSignal Step Response" and "Settling Time vs Load Capacitance" typical performance curves. +5V CHANNEL CROSSTALK 11 The two channels of the INA2132 are completely independent, including all bias circuitry. At dc and low frequency, there is virtually no signal coupling between channels. Crosstalk increases with frequency and is dependent on source impedance and signal characteristics. See the typical performance curve "Channel Separation vs Frequency" for more information. INA2132 12 (10) 2 (6) -In 13 (9) Most crosstalk is produced by capacitive coupling of signals from one channel to the input section of the other channel. To minimize coupling, separate the input traces as far as practical from any signals associated with the opposite channel. A grounded guard trace surrounding the inputs helps reduce stray coupling between channels. Run the differential inputs of each channel parallel to each other or 4 12 Bits Out 0V-4V Input 14 (8) 3 (5) +In ADS7806(1) S = 45s (4V Step to 0.01%) NOTE: (1) For 16-bit output, use ADS7809. FIGURE 5. Differential Input Data Acquisition. INA2132 -In 2 (6) BUF634 inside feedback loop contributes no error. 12 (10) Logic In VO 0 -V1 1 +V1 INA2132 2 (6) 13 (9) 12 (10) V1 BUF634 VO DG188 +In 14 (8) 3 (5) (Low IQ mode) RL VO 13 (9) 3 (5) 14 (8) 1 FIGURE 3. Low Power, High Output Current Precision Difference Amplifier. Logic In FIGURE 6. Digitally Controlled Gain of 1 Amplifier. INA2132 V2 12 (10) 2 (6) INA2132 2 (6) 12 (10) V2 13 (9) R 13 (9) R V3 R 3 (5) 14 (8) IO = (V3 - V2)/R V1 IO = (V1 - V2) (1/40k + 1/R) IO Load Load FIGURE 4. Differential Input Voltage-to-Current Converter for Low IOUT. IO FIGURE 7. Precision Voltage-to-Current Converter with Differential Inputs. (R) INA2132 14 (8) 3 (5) 8 INA2132 INA2132 2 12 13 A V1 13 A V01 14 3 12 2 V2 14 3 V3 V01 V2 6 6 10 10 9 B 8 5 9 B V02 8 5 VLS Level-Shift Voltage Reference V01 - V02 = 2 (V2 - V1) V01 = (V3 - V2) + FIGURE 8. Differential Output Difference Amplifier. VLS 2 FIGURE 9. Precision Level Shifter. V1 INA2132 -In The INA2132 can be combined with op amps to form a complete instrumentation amplifier with specialized performance characteristics. Burr-Brown offers many complete high performance IAs. Products with similar performances are shown below. A1 2 (6) 12 (10) R2 13 (9) R1 VO R2 14 (8) 3 (5) V2 +In A2 VO = (1 + 2R2 /R1) (V2 -V1) A1, A2 FEATURES SIMILAR COMPLETE BURR-BR0WN IAs OPA227 OPA129 OPA2277 OPA2130 OPA2234, OPA2241, OPA2244 OPA2237 Low Noise Ultra-Low Bias Current (fA) Low Offset Drift, Low Noise Low Power, FET-Input (pA) Single Supply, Precision, Low Power Single Supply, Low Power, MSOP-8 INA103 INA116 INA114, INA128 INA121 INA122, INA118 INA122, INA126 FIGURE 10. Precision Instrumentation Amplifier. (R) 9 INA2132 INA2132 2 (6) INA2132 2 (6) 12 (10) V2 13 (9) 12 (10) 13 (9) V0 V0 3 (5) V1 14 (8) V0 = V1 3 (5) 14 (8) FIGURE 14. Precision Unity-Gain Buffer. V0 = - V2 FIGURE 11. Precision Inverting Unity-Gain Amplifier. INA2132 12 (10) 2 (6) INA2132 2 (6) 13 (9) 12 (10) 3 (5) V0 V1 13 (9) V3 3 (5) 14 (8) V0 = 1/2 V3 V0 = 2 * V1 14 (8) V0 = V3 /2 FIGURE 15. Precision Gain = 2 Amplifier. FIGURE 12. Precision Gain = 1/2 Amplifier. INA2132 INA2132 12 (10) 2 (6) 2 (6) 12 (10) 13 (9) V1 13 (9) V1 V3 3 (5) V0 V3 V0 3 (5) 14 (8) 14 (8) V0 = (V1 + V3)/2 V0 = V1 + V3 FIGURE 13. Precision Average Value Amplifier. FIGURE 16. Precision Summing Amplifier. (R) INA2132 10 PACKAGE OPTION ADDENDUM www.ti.com 30-Jul-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) INA2132U ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR INA2132U/2K5 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR INA2132UA ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR INA2132UA/2K5 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR INA2132UA/2K5E4 OBSOLETE SOIC D 14 INA2132UA/2K5G4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR INA2132UAE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR INA2132UAG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR INA2132UE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR INA2132UG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TBD Call TI Samples Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com (3) 30-Jul-2011 MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant INA2132U/2K5 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 INA2132UA/2K5 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) INA2132U/2K5 SOIC D 14 2500 367.0 367.0 38.0 INA2132UA/2K5 SOIC D 14 2500 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated