General Description
The PVI Series Photovoltaic Isolator generates an
electrically isolated DC voltage upon receipt of a DC
input signal. It is capable of directly driving gates of
power MOSFETs or IGBTs. It utilizes a monolithic
integrated circuit photovoltaic generator of novel
construction as its output. The output is controlled by
radiation from a GaAlAs light emitting diode (LED),
which is optically isolated from the photovoltaic
generator.
The PVI Series is ideally suited for applications
requiring high-current and/or high-voltage switching
with optical isolation between the low-level driving
circuitry and high-energy or high-voltage load circuits.
It can be used for directly driving gates of power
MOSFETs. The dual-channel device allows its outputs
to drive independent discrete power MOSFETs, or be
connected in parallel or in series to provide higher
current drive for power MOSFETs or higher voltage
drive for IGBTs. The PVI Series Photovoltaic isolators
employ fast turn-off circuitry.
These PVI Series Photovoltaic Isolators are packaged
in 8-pin, molded DIP packages and available with
either thru-hole or surface-mount (gull-wing) leads,
in plastic shipping tubes.
Applications
Features
§Isolated Voltage Source
§Monolithic Construction
§Up to 8μA Output
§Single or Dual Output
§Solid-State Reliability
Part Identification
PVI1050NPbF
PVI5050NPbF thru-hole
PVI5080NPbF
PVI1050NSPbF
PVI5050NSPbF
PVI5080NSPbF
PVI1050NS-TPbF surface-mount, tape
and reel
surface-mount
(gull-wing)
§Load Distribution
§Industrial Controls
§Current-to-Voltage Conversion
§Custom Solid-State Relay
Series PVI-NPbF
Photovoltaic Isolator
Single and Dual Channel
5-10 Volt Output
1 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015
2 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015
Series PVI-NPbF
Electrical Specifications (-40°C ≤ TA ≤ +85°C unless otherwise specified)
OUTPUT CHARACTERISTICS PVI Series Units
Maximum Forward Voltage @ 10µA 8.0 per channel V(DC)
Maxiumum Reverse Current @ -10VDC 10 µA(DC)
INPUT CHARACTERISTICS PVI Series Units
Input Current Range (see figure 4) 2.0 to 50 mA (DC)
Maximum Forward Voltage Drop @ 10mA, 25°C (see figure 5) 1.4 V (DC)
Maximum Reverse Voltage 6.0 V(DC)
Maximum Reverse Current @ -6.0V (DC), 25°C 100 µA(DC)
Maximum Pulsed Input Current @ 25°C (see figure 6) 1.0 A(peak)
GENERAL CHARACTERISTICS PVI5050N/5080N PVI1050N Units
Min. Dielectric Strength, Input-Output 4000 2500 VRMS
Min. Dielectric Strength, Output-to-Output 1200 VDC
Min. Insulation Resistance, Input-to-Output
@TA=+25°C, 50%RH, 100VDC
Max. Pin Soldering Temperature (10 seconds max.) +260 °C
Ambient Temperature Range: Operating -40 to +85 °C
Storage -40 to +125 °C
1012 Ω
COUPLED CHARACTERISTICS PVI5050N PVI5080N PVI1050N Units
Minimum Open Circuit Voltage @ ILED = 10mA, 25°C, RL = >10MΩ5.0 5.0/channel V (DC)
(see figures 1 to 2) 10 series
Minimum Short Circuit Current @ ILED = 10mA, 25°C (see figures 1 to 2) 5.0 8.0 5.0 /channel µA (DC)
10 parallel
Maximum Capacitance (Input/Output) 1.0 2.0 pF
Maximum Ton Time @ ILED=10mA, CLOAD=10pF (See Figure7)
RL>20MΩ 300 µS
RL=10MΩ 160 µS
RL=4.7MΩ 90 µS
Maximum Toff Time @ ILED=10mA, CLOAD=10pF (See Figure7) 220 µS
International Rectifier does not recommend the use of this product in aerospace, avionics, military or life support applications.
Users of this International Rectifier product in such applications assume all risks of such use and indemnify International
Rectifier against all damages resulting from such use.
3 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015
Series PVI-NPbF
Output Voltage (VDC)
Figure 1. PVI5050N, PVI1050N Typical Output Characteristics
Input Current (mA)
Output Short Circuit Current (µA)
Output Voltage (VDC)
Figure 2. PVI5080N Typical Output Characteristics
Input Current (mA)
Output Short Circuit Current (µA)
0
1
2
3
4
5
6
7
8
02468101214161820
0
5
10
15
20
25
30
35
40
0
1
2
3
4
5
6
7
8
0 2 4 6 8 101214161820
0
5
10
15
20
25
30
35
40
Open Circuit Voltage
R
L
=10MΩ
R
L
=4.7MΩ
R
L
=2.2MΩ
R
L
=1MΩ
Short Circuit Current
Open Circuit Voltage
R
L
=10MΩ
R
L
=4.7MΩ
R
L
=2.2MΩ
R
L
=1MΩ
Short Circuit Current
Figure 4. Input Current Derating
Ambient Temperature (°C)
Allowable Input Current (mA)
Figure 5. Input Characteristics
Duty Cycle
Allowable Input Pulse Current (mA)
Figure 6. Input Pulse Capability
Normalized Output
Figure 3. Typical Variation of Output
Forced Air Temperature (°C)
0. 2
0. 4
0. 6
0. 8
1. 0
1. 2
1. 4
1. 6
1. 8
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
Short Circuit Current (Isc)
Output Voltage
(Voc)
LED Forward Voltage Drop (VDC)
Input Current (mA)
CAUTION: Provide current limiting
so that 50mA maximum steady-
state control current is not
exceeded.
4 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015
Series PVI-NPbF
Application Note:
The outputs of the PVI1050N (pins 5-6 and 7-8) may be placed in series connection to produce a 10-volt output
with a 5μA minimum short circuit current. Alternatively, the two ouptut of the PVI1050 may be connected in paral-
lel to produce a 5.0-volt ouput with a 10μA minimum short circuit current.
The two outputs of the PVI1050N may be applied separately with a maximum 1200VDC between the outputs.
Input-to-output isolation to either output is 2500V (RMS).
Figure 7. Typical Response Time
Response Time (µs)
Load Capacitance (pF)
Wiring Diagram
10
100
1000
10000
0 200 400 600 800 1000
Ton
R
L
=10MΩ
R
L
=4.7MΩ
R
L
=2.2MΩ
Toff
Anode
(+) 1
Cathode
Anode
Cathode
(-) 2
(+) 3
(-) 4
(-) 8
(+) 7
(-) 6
(+) 5
PVI1050N
Anode
(+) 2
Cathode
(-) 3
(+) 5
(-) 8
DC
PVI5050N
PVI5080N
7 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015
Series PVI-NPbF
Qualification standards can be found at International Rectifiers web site
http://www.irf.com/product-info/reliability
Applicable version of JEDEC standard at the time of product release.
IR WORLD HEADQUARTERS: 101 N. Sepulveda Blvd., El Segundo, California 90245, USA
To contact International Rectifier, please visit http://www.irf.com/whoto-call/
PVI1050NPbF
PVI5050NPbF
PVI5080NPbF
PVI1050NSPbF
PVI5050NSPbF MS L 4
PVI5080NSPbF (per JE DE C J-S T D-020E & JE DEC J-S T D-033C
††
)
PVI1050NS-TPbF
RoHS compliant Yes
Qualification information
†
Qualification level
Indusrial
(per JEDEC JES D47I
††
gui deli nes )
N/A
Moisture Sensitivity Level
Revision History
Date Comment
•
Added Qualification Information table on page 7.
•
Updated data sheet based on corporate template.
4/24/2015
