RGP10A
THRU
RGP10M
Features
• High temperature metallurgically bonded construction
• Glass passivated cavity-free junction
• 1.0 ampere operation at TA= 55OC with no
thermal runaway.
• Typical IR less than 0.1uA
• Fast switching for high efficiency
Maximum Ratings
• Operating Temperature: -55OC to +150CC
• Storage Temperature: -55CC to +150CC
• Typical Thermal Resistance: 55
O
C/W Junction to Ambient
MCC
Part Number
Maximum
Recurrent
Peak Reverse
Voltage
Maximum
RMS Voltage
Maximum DC
Blocking
Voltage
RGP10A 50V 35V 50V
RGP10B 100V 70V 100V
RGP10D 200V 140V 200V
RGP10G 400V 280V 400V
RGP10J 600V 420V 600V
RGP10K 800V 560V 800V
RGP10M 1000V 700V 1000V
Electrical Characteristics @ 25OC Unless Otherwise Specified
Maximum Average
Forward Current IF(AV) 1.0 A TA = 55OC
Peak Forward Surge
Current IFSM 30A 8.3ms, half sine
Maximum
Instantaneous
Forward Voltage
VF 1.3V IFM = 1.0A;
TA = 25OC
Maximum DC
Reverse Current At
Rated DC Blocking
Voltage
IR
5.0uA
200uA
TA = 25OC
TA = 150OC
Typical Junction
Capacitance CJ 15pF Measured at
1.0MHz, VR=4.0V
Maximum Reverse
Recovery Time
RGP10A-10G
RGP10J
RGP10K-10M
Trr
150nS
250nS
500nS
TJ =25OC
IF=0.5A
IR=1.0A
IRR=0.25A
DIMENSIONS
INCHES
MM
DIM MIN MAX MIN MAX NOTE
A .166 .205 4.10 5.20
B .080 .107 2.00 2.70
C .028 .034 .70 .90
D 1.000 --- 25.40 ---
www.mccsemi.com
DO-41
A
B
C
D
D
Cathode
Mark
1.0 Amp Glass
Passivated Junction
Fast Recovery
Rectifiers
50 to 1000 Volts
omponents
21201 Itasca Street Chatsworth

 !"#
$% !"#
MCC
Volts
Average Forward Rectified Current - Amperes versus
Ambient Temperature - OC
Figure 2
Forward Derating Curve
0 175 50 75 100 125
0
.2
.4
.6
Single Phase, Half Wave
60Hz Resistive or Inductive Load
Amps
O
150
.8
1.0
1.2
Instantaneous Forward Current - Amperes versus
Instantaneous Forward Voltage - Volts
Figure 1
Typical Forward Characteristics
4
6
20
10
Amps
.4 .6 .8 1.0 1.2 1.4
.01
.02
.04
.06
.1
.2
.4
.6
1
2 25OC
Junction Capacitance - pF versus
Reverse Voltage - Volts
Figure 3
Junction Capacitance
.1
.2
1
.4
2
10
20
40
4 100
1
2
6
10
20
100
pF
Volts
60
40
4
400 1000
TJ=25OC
RGP10A thru RGP10M
www.mccsemi.com
MCC
0
trr
+0.5A
0
-0.25
-1.0
1cm
Set Time Base for 20/100ns/cm
25Vdc
1Ω
50Ω10Ω
Oscilloscope
Note 1
Pulse
Generator
Note 2
Notes:
1. Rise Time = 7ns max.
Input impedance = 1 megohm, 22pF
2. Rise Time = 10ns max.
Source impedance = 50 ohms
3. Resistors are non-inductive
Figure 5
Reverse Recovery Time Characteristic And Test Circuit Diagram
1 1004
10
20
30
8
Figure 4
Peak Forward Surge Current
Peak Forward Surge Current - Amperes versus
Number Of Cycles At 60Hz - Cycles
Amps
Cycles
2
6
10 20 60
80
40
40
50
60
RGP10A thru RGP10M
www.mccsemi.com
MCC