LMH6738 LMH6738 Very Wideband, Low Distortion Triple Op Amp Literature Number: SNOSAC1D LMH6738 Very Wideband, Low Distortion Triple Op Amp General Description Features The LMH6738 is a very wideband, DC coupled monolithic operational amplifier designed specifically for ultra high resolution video systems as well as wide dynamic range systems requiring exceptional signal fidelity. Benefiting from National's current feedback architecture, the LMH6738 offers a gain range of 1 to 10 while providing stable, operation without external compensation, even at unity gain. At a gain of +2 the LMH6738 supports ultra high resolution video systems with a 400 MHz 2 VPP -3 dB Bandwidth. With 12-bit distortion levels through 30 MHz (RL = 100), 2.3 nV/ Hz input referred noise, the LMH6738 is the ideal driver or buffer for high speed flash A/D and D/A converters. Wide dynamic range systems such as radar and communication receivers requiring a wideband amplifier offering exceptional signal purity will find the LMH6738's low input referred noise and low harmonic distortion make it an attractive solution. n n n n n n n 750 MHz -3 dB small signal bandwidth (AV = +1) -85 dBc 3rd harmonic distortion (20 MHz) 2.3 nV/ Hz input noise voltage 3300 V/s slew rate 33 mA supply current (11.3 mA per op amp) 90 mA linear output current 0.02/0.01 Diff. Gain / Diff. Phase (RL = 150) Applications n n n n n n n n n RGB video driver High resolution projectors Flash A/D driver D/A transimpedance buffer Wide dynamic range IF amp Radar/communication receivers DDS post-amps Wideband inverting summer Line driver Connection Diagram 16-Pin SSOP 20097510 Top View VIP10TM is a trademark of National Semiconductor Corporation. (c) 2006 National Semiconductor Corporation DS200975 www.national.com LMH6738 Very Wideband, Low Distortion Triple Op Amp April 2006 LMH6738 Absolute Maximum Ratings (Note 1) ESD Tolerance (Note 4) Human Body Model If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (V+ - V- ) IOUT -65C to +150C 13.2V Operating Ratings (Note 1) VCC Common Mode Input Voltage Storage Temperature Range 200V Storage Temperature Range (Note 3) Maximum Junction Temperature 2000V Machine Model Thermal Resistance +150C Package -65C to +150C 16-Pin SSOP Soldering Information Infrared or Convection (20 sec.) Wave Soldering (10 sec.) 235C Operating Temperature Range 260C Supply Voltage (V+ - V- ) (JC) (JA) 36C/W 120C/W -40C 8V +85C to 12V Electrical Characteristics (Note 2) AV = +2, VCC = 5V, RL = 100, RF = 549; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Performance UGBW -3 dB Bandwidth Unity Gain, VOUT = 200 mVPP 750 SSBW -3 dB Bandwidth VOUT = 200 mVPP 480 VOUT = 2 VPP 400 LSBW MHz MHz 0.1 dB Bandwidth VOUT = 2 VPP 150 MHz GFPL Peaking DC to 75 MHz 0 dB GFR1 Rolloff DC to 150 MHz, VOUT = 2 VPP 0.1 dB GFR2 Rolloff @ 300 MHz, VOUT = 2 VPP 1.0 dB Time Domain Response TRS Rise and Fall Time (10% to 90%) 2V Step 0.9 TRL 5V Step 1.7 SR Slew Rate 5V Step 3300 V/s ts Settling Time to 0.1% 2V Step 10 ns te Enable Time From Disable = rising edge. 7.3 ns td Disable Time From Disable = falling edge. 4.5 ns 2nd Harmonic Distortion 2 VPP, 5 MHz -80 HD2 2 VPP, 20 MHz -71 HD2H 2 VPP, 50 MHz -55 ns Distortion HD2L HD3L 3rd Harmonic Distortion dBc 2 VPP, 5 MHz -90 HD3 2 VPP, 20 MHz -85 HD3H 2 VPP, 50 MHz -65 > 1 MHz > 1 MHz > 1 MHz 2.3 nV/ 12 pA/ 3 pA/ dBc Equivalent Input Noise VN Non-Inverting Voltage ICN Inverting Current NCN Non-Inverting Current Video Performance DG Differential Gain 4.43 MHz, RL = 150 .02 % DP Differential Phase 4.43 MHz, RL = 150 .01 Static, DC Performance VIO Input Offset Voltage (Note 6) IBN Input Bias Current (Note 6) Non-Inverting IBI Input Bias Current (Note 6) Inverting www.national.com -15 -20 2 0.5 2.5 4.5 mV -7 0 +5 A -2 25 35 A (Continued) AV = +2, VCC = 5V, RL = 100, RF = 549; unless otherwise specified. Symbol Parameter Min Typ 50 48.5 53 dB 46 44 50 dB Input Referred, f=10MHz, Drive channels A,C measure channel B -80 dB Supply Current (Note 6) All three amps Enabled, No Load 32 35 40 mA Supply Current Disabled V+ RL = 1.9 2.2 mA Supply Current Disabled V- RL = 1.1 1.3 mA PSRR Power Supply Rejection Ratio (Note 6) CMRR Common Mode Rejection Ratio (Note 6) XTLK Crosstalk ICC Conditions Max Units Miscellaneous Performance RIN+ Non-Inverting Input Resistance CIN+ Non-Inverting Input Capacitance RIN- Inverting Input Impedance RO Output Impedance DC VO Output Voltage Range (Note 6) RL = 100 Output impedance of input buffer. RL = 1000 k .8 pF 30 0.05 3.25 3.1 3.65 3.5 1.9 1.7 3.5 2.0 V 80 60 90 mA 160 mA V 3.8 CMIR Common Mode Input Range (Note 6) CMRR > 40 dB IO Linear Output Current (Notes 3, 6) VIN = 0V, VOUT < 30 mV ISC Short Circuit Current (Note 5) VIN = 2V Output Shorted to Ground IIH Disable Pin Bias Current High Disable Pin = V+ 10 A IIL Disable Pin Bias Current Low Disable Pin = 0V -350 A VDMAX Voltage for Disable Disable Pin VDMAX VDMIM Voltage for Enable Disable Pin VDMIN 0.8 2.0 V V Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications, see the Electrical Characteristics tables. Note 2: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where TJ > TA. See Applications Section for information on temperature de-rating of this device." Min/Max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Note 3: The maximum output current (IOUT) is determined by device power dissipation limitations. See the Power Dissipation section of the Application Section for more details. Note 4: Human Body Model is 1.5 k in series with 100 pF. Machine Model is 0 in series with 200 pF. Note 5: Short circuit current should be limited in duration to no more than 10 seconds. See the Power Dissipation section of the Application Section for more details. Note 6: Parameter 100% production tested at 25 C. Ordering Information Package 16-pin SSOP Part Number LMH6738MQ LMH6738MQX Package Marking LH6738MQ 3 Transport Media 95 Units/Rail 2.5k Units Tape and Reel NSC Drawing MQA16 www.national.com LMH6738 Electrical Characteristics (Note 2) LMH6738 Typical Performance Characteristics AV = +2, VCC = 5V, RL = 100, RF = 549; unless other- wise specified). Large Signal Frequency Response Large Signal Frequency Response 20097528 20097520 Small Signal Frequency Response Frequency Response vs. VOUT 20097501 20097513 Frequency Response vs. Supply Voltage Gain Flatness 20097530 20097516 www.national.com 4 Pulse Response Frequency Response vs. Capacitive Load 20097522 20097514 Series Output Resistance vs. Capacitive Load Open Loop Gain and Phase 20097526 20097519 Distortion vs. Frequency Distortion vs. Output Voltage 20097525 20097517 5 www.national.com LMH6738 Typical Performance Characteristics AV = +2, VCC = 5V, RL = 100, RF = 549; unless otherwise specified). (Continued) LMH6738 Typical Performance Characteristics AV = +2, VCC = 5V, RL = 100, RF = 549; unless otherwise specified). (Continued) Distortion vs. Supply Voltage CMRR vs. Frequency 20097511 20097518 PSRR vs. Frequency Crosstalk vs. Frequency 20097529 20097521 Closed Loop Output Impedance |Z| Disable Timing 20097524 20097504 www.national.com 6 DC Errors vs. Temperature Input Noise vs. Frequency 20097527 20097512 Disabled Channel Isolation vs. Frequency 20097531 7 www.national.com LMH6738 Typical Performance Characteristics AV = +2, VCC = 5V, RL = 100, RF = 549; unless otherwise specified). (Continued) LMH6738 Application Section FEEDBACK RESISTOR SELECTION One of the key benefits of a current feedback operational amplifier is the ability to maintain optimum frequency response independent of gain by using appropriate values for the feedback resistor (RF). The Electrical Characteristics and Typical Performance plots specify an RF of 550, a gain of +2 V/V and 5V power supplies (unless otherwise specified). Generally, lowering RF from it's recommended value will peak the frequency response and extend the bandwidth while increasing the value of RF will cause the frequency response to roll off faster. Reducing the value of RF too far below it's recommended value will cause overshoot, ringing and, eventually, oscillation. 20097505 FIGURE 1. Recommended Non-Inverting Gain Circuit 20097503 FIGURE 3. Recommended RF vs. Gain See Figure 3, Recommended RF. vs Gain for selecting a feedback resistor value for gains of 1 to 10. Since each application is slightly different it is worth some experimentation to find the optimal RF for a given circuit. In general a value of RF that produces ~.1 dB of peaking is the best compromise between stability and maximal bandwidth. Note that it is not possible to use a current feedback amplifier with the output shorted directly to the inverting input. The buffer configuration of the LMH6738 requires a 750 feedback resistor for stable operation. The LMH6738 was optimized for high speed operation. As shown in Figure 3 the suggested value for RF decreases for higher gains. Due to the impedance of the input buffer there is a practical limit for how small RFcan go, based on the lowest practical value of RG. This limitation applies to both inverting and non inverting configurations. For the LMH6738 the input resistance of the inverting input is approximately 30 and 20 is a practical (but not hard and fast) lower limit for RG. The LMH6738 begins to operate in a gain bandwidth limited fashion in the region where RG is nearly equal to the input buffer impedance. Note that the amplifier will operate with RG values well below 20, however results may be substantially different than predicted from ideal models. In particular the voltage potential between the Inverting and Non Inverting inputs cannot be expected to remain small. Inverting gain applications that require impedance matched inputs may limit gain flexibility somewhat (especially if maximum bandwidth is required). The impedance seen by the source is RG || RT (RT is optional). The value of RG is RF 20097506 FIGURE 2. Recommended Inverting Gain Circuit GENERAL INFORMATION The LMH6738 is a high speed current feedback amplifier, optimized for very high speed and low distortion. The LMH6738 has no internal ground reference so single or split supply configurations are both equally useful. EVALUATION BOARDS National Semiconductor provides the following evaluation boards as a guide for high frequency layout and as an aid in device testing and characterization. Many of the datasheet plots were measured with these boards. Device Package Evaluation Board Part Number LMH6738MQA SSOP LMH730275 A bare evaluation board is shipped when a sample request is placed with National Semiconductor. www.national.com 8 LMH6738 Application Section (Continued) /Gain. Thus for an inverting gain of -7 V/V and an optimal value for RF the input impedance is equal to 50. Using a termination resistor this can be brought down to match a 25 source, however, a 150 source cannot be matched. To match a 150 source would require using a 1050 feedback resistor and would result in reduced bandwidth. For more information see Application Note OA-13 which describes the relationship between RF and closed-loop frequency response for current feedback operational amplifiers. The value for the inverting input impedance for the LMH6738 is approximately 30. The LMH6738 is designed for optimum performance at gains of +1 to +10 V/V and -1 to -9 V/V. Higher gain configurations are still useful, however, the bandwidth will fall as gain is increased, much like a typical voltage feedback amplifier. 20097508 FIGURE 5. Decoupling Capacitive Loads DRIVING CAPACITIVE LOADS Capacitive output loading applications will benefit from the use of a series output resistor ROUT. Figure 5 shows the use of a series output resistor, ROUT, to stabilize the amplifier output under capacitive loading. Capacitive loads of 5 to 120 pF are the most critical, causing ringing, frequency response peaking and possible oscillation. The charts "Suggested ROUT vs. Cap Load" give a recommended value for selecting a series output resistor for mitigating capacitive loads. The values suggested in the charts are selected for .5 dB or less of peaking in the frequency response. This gives a good compromise between settling time and bandwidth. For applications where maximum frequency response is needed and some peaking is tolerable, the value of ROUT can be reduced slightly from the recommended values. An alternative approach is to place Rout inside the feedback loop as shown in Figure 6. This will preserve gain accuracy, but will still limit maximum output voltage swing. ACTIVE FILTER When using any current feedback Operational Amplifier as an active filter it is necessary to be careful using reactive components in the feedback loop. Reducing the feedback impedance, especially at higher frequencies, will almost certainly cause stability problems. Likewise capacitance on the inverting input should be avoided. See Application Notes OA-7 and OA-26 for more information on Active Filter applications for Current Feedback Op Amps. When using the LMH6738 as a low pass filter the value of RF can be substantially reduced from the value recommended in the RF vs. Gain charts. The benefit of reducing RF is increased gain at higher frequencies, which improves attenuation in the stop band. Stability problems are avoided because in the stop band additional device bandwidth is used to cancel the input signal rather than amplify it. The benefit of this change depends on the particulars of the circuit design. With a high pass filter configuration reducing RF will likely result in device instability and is not recommended. 20097509 FIGURE 6. Series Output Resistor Inside Feedback Loop INVERTING INPUT PARASITIC CAPACITANCE Parasitic capacitance is any capacitance in a circuit that was not intentionally added. It comes about from electrical interaction between conductors. Parasitic capacitance can be reduced but never entirely eliminated. Most parasitic capacitances that cause problems are related to board layout or lack of termination on transmission lines. Please see the section on Layout Considerations for hints on reducing problems due to parasitic capacitances on board traces. Transmission lines should be terminated in their characteristic impedance at both ends. High speed amplifiers are sensitive to capacitance between the inverting input and ground or power supplies. This shows up as gain peaking at high frequency. The capacitor raises device gain at high frequencies by making RG appear smaller. Capacitive output loading will exaggerate this effect. In general, avoid introducing unnecessary parasitic capacitance at both the inverting input and the output. 20097507 FIGURE 4. Typical Video Application 9 www.national.com LMH6738 Application Section (Continued) POWER DISSIPATION The LMH6738 is optimized for maximum speed and performance in the small form factor of the standard SSOP-16 package. To achieve its high level of performance, the LMH6738 consumes an appreciable amount of quiescent current which cannot be neglected when considering the total package power dissipation limit. The quiescent current contributes to about 40 C rise in junction temperature when no additional heat sink is used (VS = 5V, all 3 channels on). Therefore, it is easy to see the need for proper precautions to be taken in order to make sure the junction temperature's absolute maximum rating of 150C is not violated. To ensure maximum output drive and highest performance, thermal shutdown is not provided. Therefore, it is of utmost importance to make sure that the TJMAX is never exceeded due to the overall power dissipation (all 3 channels). One possible remedy for this effect is to slightly increase the value of the feedback (and gain set) resistor. This will tend to offset the high frequency gain peaking while leaving other parameters relatively unchanged. If the device has a capacitive load as well as inverting input capacitance using a series output resistor as described in the section on "Driving Capacitive Loads" will help. LAYOUT CONSIDERATIONS Whenever questions about layout arise, use the evaluation board as a guide. The LMH730275 is the evaluation board supplied with samples of the LMH6738. To reduce parasitic capacitances ground and power planes should be removed near the input and output pins. Components in the feedback loop should be placed as close to the device as possible. For long signal paths controlled impedance lines should be used, along with impedance matching elements at both ends. With the LMH6738 used in a back-terminated 75 RGB analog video system (with 2 VPP output voltage), the total power dissipation is around 435 mW of which 340 mW is due to the quiescent device dissipation (output black level at 0V). With no additional heat sink used, that puts the junction temperature to about 140 C when operated at 85C ambient. To reduce the junction temperature many options are available. Forced air cooling is the easiest option. An external add-on heat-sink can be added to the SSOP-16 package, or alternatively, additional board metal (copper) area can be utilized as heat-sink. An effective way to reduce the junction temperature for the SSOP-16 package (and other plastic packages) is to use the copper board area to conduct heat. With no enhancement the major heat flow path in this package is from the die through the metal lead frame (inside the package) and onto the surrounding copper through the interconnecting leads. Since high frequency performance requires limited metal near the device pins the best way to use board copper to remove heat is through the bottom of the package. A gap filler with high thermal conductivity can be used to conduct heat from the bottom of the package to copper on the circuit board. Vias to a ground or power plane on the back side of the circuit board will provide additional heat dissipation. A combination of front side copper and vias to the back side can be combined as well. Follow these steps to determine the Maximum power dissipation for the LMH6738: 1. Calculate the quiescent (no-load) power: PAMP = ICC* (VS) VS = V+-V- 2. Calculate the RMS power dissipated in the output stage: PD (rms) = rms ((VS - VOUT)*IOUT) where VOUT and IOUT are the voltage and current across the external load and VS is the total supply current Bypass capacitors should be placed as close to the device as possible. Bypass capacitors from each rail to ground are applied in pairs. The larger electrolytic bypass capacitors can be located farther from the device, the smaller ceramic capacitors should be placed as close to the device as possible. The LMH6738 has multiple power and ground pins for enhanced supply bypassing. Every pin should ideally have a separate bypass capacitor. Sharing bypass capacitors may slightly degrade second order harmonic performance, especially if the supply traces are thin and /or long. In Figure 1 and Figure 2 CSS is optional, but is recommended for best second harmonic distortion. Another option to using CSS is to use pairs of .01 F and .1 F ceramic capacitors for each supply bypass. VIDEO PERFORMANCE The LMH6738 has been designed to provide excellent performance with production quality video signals in a wide variety of formats such as HDTV and High Resolution VGA. NTSC and PAL performance is nearly flawless. Best performance will be obtained with back terminated loads. The back termination reduces reflections from the transmission line and effectively masks transmission line and other parasitic capacitances from the amplifier output stage. Figure 4 shows a typical configuration for driving a 75 Cable. The amplifier is configured for a gain of two to make up for the 6 dB of loss in ROUT. 3. Calculate the total RMS power: PT = PAMP+PD The maximum power that the LMH6738, package can dissipate at a given temperature can be derived with the following equation (See Figure 7): PMAX = (150o - TAMB)/ JA, where TAMB = Ambient temperature (C) and JA = Thermal resistance, from junction to ambient, for a given package (C/W). For the SSOP package JA is 120C/W. 20097502 FIGURE 7. Maximum Power Dissipation www.national.com 10 The current that flows through the ESD diodes will either exit the chip through the supply pins or will flow through the device, hence it is possible to power up a chip with a large signal applied to the input pins. Shorting the power pins to each other will prevent the chip from being powered up through the input. (Continued) ESD PROTECTION The LMH6738 is protected against electrostatic discharge (ESD) on all pins. The LMH6738 will survive 2000V Human Body model and 200V Machine model events. Under closed loop operation the ESD diodes have no effect on circuit performance. There are occasions, however, when the ESD diodes will be evident. If the LMH6738 is driven by a large signal while the device is powered down the ESD diodes will conduct. 11 www.national.com LMH6738 Application Section LMH6738 Very Wideband, Low Distortion Triple Op Amp Physical Dimensions inches (millimeters) unless otherwise noted 16-Pin SSOP NS Package Number MQA16 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated