Device
Number
Nominal
Zener
Voltage
VZ @ IZT
(Note 1)
Test
Current
IZT
Max Zener Impedance
Max Reverse
Leakage Current Max Surge
Current
ir
(Note 2)
Max
Voltage
Regulation
VZ
(Note 3)
Max
Regulator
Current
IZM
ZZT @ IZT
(Note 1)
ZZK @ IZK = 1mA
(Note 1) IR@V
R
Volts mA AVolts Amps Volt mA
1N5341B 6.2 200 1200 1 3 12.4 0.1 765
1N5342B 6.8 175 1200 10 5.2 11.5 0.15 700
1N5343B 7.5 175 1.5 200 10 5.7 10.7 0.15 630
1N5344B 8.2 150 1.5 200 10 6.2 10 0.2 580
1N5345B 8.7 150 2200 10 6.6 9.5 0.2 545
1N5346B 9.1 150 2150 7.5 6.9 9.2 0.22 520
1N5347B 10 125 2125 57.6 8.6 0.22 475
1N5348B 11 125 2.5 125 58.4 80.25 430
1N5349B 12 100 2.5 125 29.1 7.5 0.25 395
1N5350B 13 100 2.5 100 19.9 70.25 365
1N5351B 14 100 2.5 75 110.6 6.7 0.25 340
1N5352B 15 75 2.5 75 111.5 6.3 0.25 315
1N5353B 16 75 2.5 75 112.2 60.3 295
1N5354B 17 70 2.5 75 0.5 12.9 5.8 0.35 280
1N5355B 18 65 2.5 75 0.5 13.7 5.5 0.4 265
1N5356B 19 65 375 0.5 14.4 5.3 0.4 250
1N5357B 20 65 375 0.5 15.2 5.1 0.4 237
1N5358B 22 50 3.5 75 0.5 16.7 4.7 0.45 216
1N5359B 24 50 3.5 100 0.5 18.2 4.4 0.55 198
1N5360B 25 50 4110 0.5 19 4.3 0.55 190
1N5361B 27 50 5120 0.5 20.6 4.1 0.6 176
1N5362B 28 50 6130 0.5 21.2 3.9 0.6 170
1N5363B 30 40 8140 0.5 22.8 3.7 0.6 158
1N5364B 33 40 10 150 0.5 25.1 3.5 0.6 144
1N5365B 36 30 11 160 0.5 27.4 3.3 0.65 132
1N5366B 39 30 14 170 0.5 29.7 3.1 0.65 122
1N5367B 43 30 20 190 0.5 32.7 2.8 0.7 110
1N5368B 47 25 25 210 0.5 35.8 2.7 0.8 100
1N5369B 51 25 27 230 0.5 38.8 2.5 0.9 93
1N5370B 56 20 35 280 0.5 42.6 2.3 186
1N5371B 60 20 40 350 0.5 42.5 2.2 1.2 79
Note 1 Test conditions for zener voltage and impedance are as follows: IZ is applied 40 10ms prior
to reading. Mounting contacts are located 3/8” to 1/2” from the inside edge of mounting clips
to the body of the diode (TA = +25C +8, −2C).
Note 2 Surge current is specified as the maximum allowable peak, non−recurrent square−wave cur-
rent with a pulse width, PW, of 8.3ms. Mounting contact located as specified in Note 1.
Note 3 Test conditions for voltage regulation are as follows: VZ measurements are made at 10%
and then at 50% of the IZ max value listed in the “Electrical Characteristic” table. The test
current time duration for each VZ measurement is 40 10ms (TA = +25C +8, −2C). Mount-
ing contact located as specified in Note 1.