www.ti.com TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION SLLS792 - JUNE 2007 FEATURES APPLICATIONS * * * * * * * * * * * ESD Protection for RS-232 Pins - 15-kV Human-Body Model (HBM) - 8 kV (IEC 61000-4-2, Contact Discharge) - 15 kV (IEC 61000-4-2, Air-Gap Discharge) Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards Operates With 3-V to 5.5-V VCC Supply Operates up to 250 kbit/s One Driver and One Receiver Low Standby Current . . . 1 A Typical External Capacitors . . . 4 x 0.1 F Accepts 5-V Logic Input With 3.3-V Supply Alternative High-Speed Pin-Compatible Device (1 Mbit/s) - TRSF3221E Auto-Powerdown Feature Automatically Disables Drivers for Power Savings * * * * Battery-Powered, Hand-Held, and Portable Equipment PDAs and Palmtop PCs Notebooks, Subnotebooks, and Laptops Digital Cameras Mobile Phones and Wireless Devices DB OR PW PACKAGE (TOP VIEW) EN C1+ V+ C1- C2+ C2- V- RIN 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 FORCEOFF VCC GND DOUT FORCEON DIN INVALID ROUT DESCRIPTION/ORDERING INFORMATION The TRS3221E is a single driver, single receiver RS-232 solution operating from a single VCC supply. The RS-232 pins provide IEC G1000-4-2 ESD protection. The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. These devices operate at data signaling rates up to 250 kbit/s and a maximum of 30-V/s driver output slew rate. Flexible control options for power management are available when the serial port is inactive. The auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal on the receiver input, the driver output is disabled. If FORCEOFF is set low and EN is high, both the driver and receiver are shut off, and the supply current is reduced to 1 A. Disconnecting the serial port or turning off the peripheral drivers causes the auto-powerdown condition to occur. Auto-powerdown can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown enabled, the device is activated automatically when a valid signal is applied to the receiver input. The INVALID output notifies the user if an RS-232 signal is present at the receiver input. INVALID is high (valid data) if the receiver input voltage is greater than 2.7 V or less than -2.7 V, or has been between -0.3 V and 0.3 V for less than 30 s. INVALID is low (invalid data) if the receiver input voltage is between -0.3 V and 0.3 V for more than 30 s. Refer to Figure 5 for receiver input levels. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2007, Texas Instruments Incorporated TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS792 - JUNE 2007 ORDERING INFORMATION TA PACKAGE SSOP - DB 0C to 70C TSSOP - PW SSOP - DB -40C to 85C TSSOP - PW (1) (2) (1) (2) ORDERABLE PART NUMBER Tube of 80 TRS3221ECDB Reel of 2000 TRS3221ECDBR Tube of 90 TRS3221ECPW Reel of 2000 TRS3221ECPWR Tube of 80 TRS3221EIDB Reel of 2000 TRS3221EIDBR Tube of 90 TRS3221EIPW Reel of 2000 TRS3221EIPWR TOP-SIDE MARKING RS21EC RS21EC RS21EI RS21EI Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. FUNCTION TABLES ABC EACH DRIVER (1) INPUTS DIN (1) FORCEON FORCEOFF VALID RIN RS-232 LEVEL OUTPUT DOUT DRIVER STATUS X X L X Z Powered off L H H X H H H H X L Normal operation with auto-powerdown disabled L L H Yes H H L H Yes L L L H No Z H L H No Z Normal operation with auto-powerdown enabled Powered off by auto-powerdown feature H = high level, L = low level, X = irrelevant, Z = high impedance EACH RECEIVER (1) INPUTS (1) 2 RIN EN VALID RIN RS-232 LEVEL OUTPUT ROUT L L X H H L X L X H X Z Open L No H H = high level, L = low level, X = irrelevant, Z = high impedance (off), Open = disconnected input or connected driver off Submit Documentation Feedback TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS792 - JUNE 2007 LOGIC DIAGRAM (POSITIVE LOGIC) DIN FORCEOFF FORCEON ROUT 11 13 DOUT 16 Auto-Powerdown 12 9 10 8 1 INVALID RIN EN Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range (2) -0.3 6 V V+ Positive output supply voltage range (2) -0.3 7 V 0.3 -7 V 13 V V- Negative output supply voltage range V+ - V- Supply voltage difference (2) (2) VI Input voltage range VO Output voltage range JA Package thermal impedance (3) (4) TJ Operating virtual junction temperature Tstg Storage temperature range (1) (2) (3) (4) DIN, FORCEOFF, FORCEON, EN -0.3 6 RIN -25 25 DOUT ROUT, INVALID -13.2 13.2 -0.3 VCC + 0.3 DB package 82 PW package 108 -65 UNIT V V C/W 150 C 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to network GND. Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/JA. Operating at the absolute maximum TJ of 150C can affect reliability. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) See Figure 6 VCC = 3.3 V Supply voltage VCC = 5 V VIH Driver and control high-level input voltage DIN, FORCEOFF, FORCEON, EN VIL Driver and control low-level input voltage DIN, FORCEOFF, FORCEON, EN VI Driver and control input voltage DIN, FORCEOFF, FORCEON VI Receiver input voltage TA Operating free-air temperature (1) TRS3221EC TRS3221EI VCC = 3.3 V VCC = 5 V MIN NOM MAX 3 3.3 3.6 4.5 5 5.5 2 UNIT V V 2.4 0.8 V 0 5.5 V -25 25 V 0 70 -40 85 C Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. Submit Documentation Feedback 3 TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS792 - JUNE 2007 Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER II Input leakage current TEST CONDITIONS FORCEOFF, FORCEON, EN Supply current Powered off VCC = 3.3 V or 5 V, TA = 25C Auto-powerdown enabled (1) (2) TYP (2) MAX UNIT 0.01 1 A 0.3 1 mA No load, FORCEOFF at GND 1 10 No load, FORCEOFF at VCC, FORCEON at GND, All RIN are open or grounded 1 10 No load, FORCEOFF and FORCEON at VCC Auto-powerdown disabled ICC MIN A Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Driver Section Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER TEST CONDITIONS MIN TYP (2) 5.4 VOH High-level output voltage DOUT at RL = 3 k to GND, DIN = GND 5 VOL Low-level output voltage DOUT at RL = 3 k to GND, DIN = VCC -5 IIH High-level input current VI = VCC IIL Low-level input current VI = GND IOS Short-circuit output current (3) VCC = 3.6 V, VO = 0 V VCC = 5.5 V, VO = 0 V ro Output resistance VCC, V+, and V- = 0 V, VO = 2 V Ioff (1) (2) (3) Output leakage current FORCEOFF = GND UNIT V -5.4 0.01 300 MAX V 1 A 0.01 1 A 35 60 35 60 mA 10M VO = 12 V, VCC = 3 V to 3.6 V 25 VO = 10 V, VCC = 4.5 V to 5.5 V 25 A Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Short-circuit durations should be controlled to prevent exceeding the device absolute power-dissipation ratings, and not more than one output should be shorted at a time. Driver Section Switching Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER Maximum data rate CL = 1000 pF, RL = 3 k, See Figure 1 tsk(p) Pulse skew (3) CL = 150 pF to 2500 pF, RL = 3 k to 7 k, See Figure 2 SR(tr) Slew rate, transition region (see Figure 1) (1) (2) (3) 4 TEST CONDITIONS VCC = 3.3 V, RL = 3 k to 7 k MIN TYP (2) 150 250 MAX kbit/s 100 ns CL = 150 pF to 1000 pF 6 30 CL = 150 pF to 2500 pF 4 30 Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Pulse skew is defined as |tPLH - tPHL| of each channel of the same device. Submit Documentation Feedback UNIT V/s TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS792 - JUNE 2007 Receiver Section Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER TEST CONDITIONS VOH High-level output voltage IOH = -1 mA VOL Low-level output voltage IOL = 1.6 mA VIT+ Positive-going input threshold voltage VIT- Negative-going input threshold voltage Vhys Input hysteresis (VIT+ - VIT-) Ioff Output leakage current EN = VCC ri Input resistance VI = 3 V to 25 V (1) (2) MIN TYP (2) VCC - 0.6 VCC - 0.1 MAX V 0.4 VCC = 3.3 V 1.6 2.4 VCC = 5 V 1.9 2.4 VCC = 3.3 V 0.6 1.1 VCC = 5 V 0.8 1.4 V V V 0.5 3 UNIT V 0.05 10 A 5 7 k Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Receiver Section Switching Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER TEST CONDITIONS TYP (2) UNIT tPLH Propagation delay time, low- to high-level output CL = 150 pF, See Figure 3 150 ns tPHL Propagation delay time, high- to low-level output CL = 150 pF, See Figure 3 150 ns ten Output enable time CL = 150 pF, RL = 3 k, See Figure 4 200 ns tdis Output disable time CL = 150 pF, RL = 3 k, See Figure 4 200 ns tsk(p) Pulse skew (3) See Figure 3 50 ns (1) (2) (3) Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Pulse skew is defined as |tPLH - tPHL| of each channel of the same device. ESD Protection NAME TEST CONDITIONS UNIT 15 HBM RIN/DOUT TYP IEC G1000-4-2 Contact Discharge 8 IEC G1000-4-2 Air-Gap Discharge 15 Submit Documentation Feedback kV 5 TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS792 - JUNE 2007 Auto-Powerdown Section Electrical Characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER TEST CONDITIONS MIN VT+(valid) Receiver input threshold for INVALID high-level output voltage FORCEON = GND, FORCEOFF = VCC VT-(valid) Receiver input threshold for INVALID high-level output voltage FORCEON = GND, FORCEOFF = VCC -2.7 VT(invalid) Receiver input threshold for INVALID low-level output voltage FORCEON = GND, FORCEOFF = VCC -0.3 VOH INVALID high-level output voltage IOH = -1 mA, FORCEON = GND, FORCEOFF = VCC VOL INVALID low-level output voltage IOL = 1.6 mA, FORCEON = GND, FORCEOFF = VCC MAX UNIT 2.7 V V 0.3 V VCC - 0.6 V 0.4 V Auto-Powerdown Section Switching Characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER UNIT tvalid Propagation delay time, low- to high-level output 1 s tinvalid Propagation delay time, high- to low-level output 30 s ten Supply enable time 100 s (1) 6 TYP (1) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Submit Documentation Feedback TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS792 - JUNE 2007 PARAMETER MEASUREMENT INFORMATION FORCEON 3V Generator (see Note B) 3V Input RS-232 Output 50 RL tTHL CL (see Note A) 3V FORCEOFF TEST CIRCUIT 0V 3V 3V Output SR(tr) + tTLH -3 V -3 V 6V t THL or tTLH VOH VOL VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. Figure 1. Driver Slew Rate FORCEON 3V Generator (see Note B) 3V RS-232 Output 50 RL Input 1.5 V 1.5 V 0V CL (see Note A) tPLH tPHL VOH 3V FORCEOFF 50% 50% Output VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. Figure 2. Driver Pulse Skew EN = VCC 3V Input 1.5 V 1.5 V -3 V Output Generator (see Note B) tPHL 50 tPLH CL (see Note A) VOH 50% Output 50% VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. Figure 3. Receiver Propagation Delay Times Submit Documentation Feedback 7 TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS792 - JUNE 2007 PARAMETER MEASUREMENT INFORMATION 3V Input VCC 1.5 V GND S1 0V tPZH (S1 at GND) tPHZ (S1 at GND) RL 3 V or 0 V 1.5 V VOH Output 50% Output CL (see Note A) EN Generator (see Note B) 50 0.3 V tPLZ (S1 at VCC) tPZL (S1 at VCC) 0.3 V Output 50% VOL TEST CIRCUIT NOTES: A. B. C. D. VOLTAGE WAVEFORMS CL includes probe and jig capacitance. The pulse generator has the following characteristics: ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. tPLZ and tPHZ are the same as tdis. tPZL and tPZH are the same as ten. Figure 4. Receiver Enable and Disable Times 8 Submit Documentation Feedback TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS792 - JUNE 2007 PARAMETER MEASUREMENT INFORMATION 2.7 V EN = GND 3V 0V Receiver Input 0V ROUT Generator (see Note B) 2.7 V -2.7 V -2.7 V 50 -3 V tvalid tinvalid VCC Autopowerdown INVALID INVALID Output CL = 30 pF (see Note A) FORCEOFF FORCEON DIN DOUT 50% VCC 50% VCC 0V ten V+ V+ Supply Voltages 0.3 V VCC 0V 0.3 V V- TEST CIRCUIT V- IIIIIIIIIII IIIIIIIIIII IIIIIIIIIII IIIIIIIIIII IIIIIIIIIII IIIIIIIIIII IIIIIIIIIII IIIIIIIIIII VOLTAGE WAVEFORMS Valid RS-232 Level, INVALID High 2.7 V Indeterminate 0.3 V 0V If Signal Remains Within This Region For More Than 30 s, INVALID Is Low -0.3 V Indeterminate -2.7 V Valid RS-232 Level, INVALID High Auto-powerdown disables drivers and reduces supply current to 1 A. NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 5 kbit/s, ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. Figure 5. INVALID Propagation Delay Times and Driver Enabling Time Submit Documentation Feedback 9 TRS3221E 3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS792 - JUNE 2007 APPLICATION INFORMATION EN 16 1 2 VCC C1+ 15 + 3 C1 + + - - V+ Autopowerdown C3(1) 4 GND - 14 13 6 C2- 7 RIN 12 C2 11 V- 10 C4 + DOUT C2+ + - CBYPASS = 0.1 F C1- 5 - FORCEOFF 8 9 FORCEON DIN INVALID ROUT 5 k (1) C3 can be connected to VCC or GND. NOTES: A. Resistor values shown are nominal. B. Nonpolarized ceramic capacitors are acceptable. If polarized tantalum or electrolytic capacitors are used, they should be connected as shown. VCC vs CAPACITOR VALUES VCC C1 C2, C3, and C4 3.3 V 0.3 V 5 V 0.5 V 3 V to 5.5 V 0.1 F 0.047 F 0.1 F 0.1 F 0.33 F 0.47 F Figure 6. Typical Operating Circuit and Capacitor Values 10 Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 26-Sep-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TRS3221ECDB ACTIVE SSOP DB 16 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221ECDBG4 ACTIVE SSOP DB 16 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221ECDBR ACTIVE SSOP DB 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221ECDBRG4 ACTIVE SSOP DB 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221ECPW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221ECPWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221ECPWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221ECPWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221EIDB ACTIVE SSOP DB 16 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221EIDBG4 ACTIVE SSOP DB 16 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221EIDBR ACTIVE SSOP DB 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221EIDBRG4 ACTIVE SSOP DB 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221EIPW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221EIPWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221EIPWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3221EIPWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 26-Sep-2007 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 12.0 16.0 Q1 TRS3221ECDBR SSOP DB 16 2000 330.0 16.4 8.2 6.6 2.5 TRS3221ECPWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TRS3221EIDBR SSOP DB 16 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 TRS3221EIPWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TRS3221ECDBR SSOP DB 16 2000 367.0 367.0 38.0 TRS3221ECPWR TSSOP PW 16 2000 367.0 367.0 35.0 TRS3221EIDBR SSOP DB 16 2000 367.0 367.0 38.0 TRS3221EIPWR TSSOP PW 16 2000 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA MSSO002E - JANUARY 1995 - REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0-8 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated