ON Semiconductor BC846AWT1 Series, BC847AWT1 Series, BC848AWT1 Series General Purpose Transistors NPN Silicon These transistors are designed for general purpose amplifier applications. They are housed in the SOT-323/SC-70 which is designed for low power surface mount applications. MAXIMUM RATINGS Rating Symbol BC846 BC847 BC848 Unit Collector-Emitter Voltage VCEO 65 45 30 V Collector-Base Voltage VCBO 80 50 30 V Emitter-Base Voltage VEBO 6.0 6.0 5.0 V IC 100 100 100 mAdc Collector Current -- Continuous 3 1 2 THERMAL CHARACTERISTICS Characteristic Symbol Max Unit Total Device Dissipation FR-5 Board, (1) TA = 25C PD 150 mW Thermal Resistance, Junction to Ambient RJA 833 C/W PD 2.4 mW/C TJ, Tstg -55 to +150 C Total Device Dissipation Junction and Storage Temperature CASE 419-02, STYLE 3 SOT-323/SC-70 COLLECTOR 3 1 BASE DEVICE MARKING BC846AWT1 = 1A; BC846BWT1 = 1B; BC847AWT1 = 1E; BC847BWT1 = 1F; BC847CWT1 = 1G; BC848AWT1 = 1J; BC848BWT1 = 1K; BC848CWT1 = 1L 2 EMITTER ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Characteristic Symbol Min Typ Max Unit OFF CHARACTERISTICS Collector-Emitter Breakdown Voltage (IC = 10 mA) BC846 Series BC847 Series BC848 Series V(BR)CEO 65 45 30 -- -- -- -- -- -- V Collector-Emitter Breakdown Voltage (IC = 10 A, VEB = 0) BC846 Series BC847 Series BC848 Series V(BR)CES 80 50 30 -- -- -- -- -- -- V Collector-Base Breakdown Voltage (IC = 10 A) BC846 Series BC847 Series BC848 Series V(BR)CBO 80 50 30 -- -- -- -- -- -- V Emitter-Base Breakdown Voltage (IE = 1.0 A) BC846 Series BC847 Series BC848 Series V(BR)EBO 6.0 6.0 5.0 -- -- -- -- -- -- V ICBO -- -- -- -- 15 5.0 nA A Collector Cutoff Current (VCB = 30 V) (VCB = 30 V, TA = 150C) 1. FR-5 = 1.0 x 0.75 x 0.062 in Semiconductor Components Industries, LLC, 2001 September, 2001 - Rev. 2 1 Publication Order Number: BC846AWT1/D BC846AWT1 Series, BC847AWT1 Series, BC848AWT1 Series ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) (Continued) Characteristic Symbol Min Typ Max Unit hFE -- -- -- 90 150 270 -- -- -- -- 110 200 420 180 290 520 220 450 800 ON CHARACTERISTICS DC Current Gain (IC = 10 A, VCE = 5.0 V) (IC = 2.0 mA, VCE = 5.0 V) BC846A, BC847A, BC848A BC846B, BC847B, BC848B BC847C, BC848C BC846A, BC847A, BC848A BC846B, BC847B, BC848B BC847C, BC848C Collector-Emitter Saturation Voltage (IC = 10 mA, IB = 0.5 mA) Collector-Emitter Saturation Voltage (IC = 100 mA, IB = 5.0 mA) VCE(sat) -- -- -- -- 0.25 0.6 V Base-Emitter Saturation Voltage (IC = 10 mA, IB = 0.5 mA) Base-Emitter Saturation Voltage (IC = 100 mA, IB = 5.0 mA) VBE(sat) -- -- 0.7 0.9 -- -- V Base-Emitter Voltage (IC = 2.0 mA, VCE = 5.0 V) Base-Emitter Voltage (IC = 10 mA, VCE = 5.0 V) VBE(on) 580 -- 660 -- 700 770 mV fT 100 -- -- MHz Cobo -- -- 4.5 pF NF -- -- 10 dB SMALL-SIGNAL CHARACTERISTICS Current-Gain -- Bandwidth Product (IC = 10 mA, VCE = 5.0 Vdc, f = 100 MHz) Output Capacitance (VCB = 10 V, f = 1.0 MHz) Noise Figure (IC = 0.2 mA, VCE = 5.0 Vdc, RS = 2.0 k, f = 1.0 kHz, BW = 200 Hz) Figure 1. http://onsemi.com 2 BC846AWT1 Series, BC847AWT1 Series, BC848AWT1 Series BC847 SERIES & BC848 SERIES 1.0 VCE = 10 V TA = 25C 1.5 TA = 25C 0.9 0.8 1.0 V, VOLTAGE (VOLTS) hFE , NORMALIZED DC CURRENT GAIN 2.0 0.8 0.6 0.4 VBE(sat) @ IC/IB = 10 0.7 VBE(on) @ VCE = 10 V 0.6 0.5 0.4 0.3 0.2 0.3 VCE(sat) @ IC/IB = 10 0.1 0.2 0.2 0.5 50 1.0 20 2.0 5.0 10 IC, COLLECTOR CURRENT (mAdc) 100 0 0.1 200 0.2 0.3 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10 20 30 IC, COLLECTOR CURRENT (mAdc) Figure 2. "Saturation" and "On" Voltages 2.0 VB, TEMPERATURE COEFFICIENT (mV/ C) VCE , COLLECTOR-EMITTER VOLTAGE (V) Figure 1. Normalized DC Current Gain TA = 25C 1.6 IC = 200 mA 1.2 IC = IC = IC = 50 mA 10 mA 20 mA 0.8 IC = 100 mA 0.4 0 0.02 10 0.1 1.0 IB, BASE CURRENT (mA) 20 1.0 -55C to +125C 1.2 1.6 2.0 2.4 2.8 Cib Cob 2.0 0.4 0.6 0.8 1.0 2.0 4.0 6.0 8.0 10 VR, REVERSE VOLTAGE (VOLTS) 20 40 f, T CURRENT-GAIN - BANDWIDTH PRODUCT (MHz) C, CAPACITANCE (pF) TA = 25C 3.0 1.0 100 Figure 4. Base-Emitter Temperature Coefficient 10 5.0 10 1.0 IC, COLLECTOR CURRENT (mA) 0.2 Figure 3. Collector Saturation Region 7.0 50 70 100 Figure 5. Capacitances 400 300 200 VCE = 10 V TA = 25C 100 80 60 40 30 20 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10 20 IC, COLLECTOR CURRENT (mAdc) 30 Figure 6. Current-Gain - Bandwidth Product http://onsemi.com 3 50 BC846AWT1 Series, BC847AWT1 Series, BC848AWT1 Series BC846 SERIES TA = 25C VCE = 5 V TA = 25C 0.8 V, VOLTAGE (VOLTS) hFE , DC CURRENT GAIN (NORMALIZED) 1.0 2.0 1.0 0.5 VBE(sat) @ IC/IB = 10 0.6 VBE @ VCE = 5.0 V 0.4 0.2 0.2 VCE(sat) @ IC/IB = 10 0 10 100 1.0 IC, COLLECTOR CURRENT (mA) 0.1 0.2 0.2 0.5 1.0 2.0 TA = 25C 1.6 20 mA 50 mA 100 mA 200 mA 1.2 IC = 10 mA 0.8 0.4 0 0.02 0.05 0.1 0.2 0.5 1.0 2.0 IB, BASE CURRENT (mA) 5.0 10 20 f, T CURRENT-GAIN - BANDWIDTH PRODUCT C, CAPACITANCE (pF) TA = 25C Cib 10 6.0 2.0 Cob 0.1 0.2 0.5 5.0 1.0 2.0 10 20 VR, REVERSE VOLTAGE (VOLTS) 200 50 100 200 -1.4 -1.8 50 VB for VBE -55C to 125C -2.2 -2.6 -3.0 0.2 0.5 10 20 1.0 2.0 5.0 IC, COLLECTOR CURRENT (mA) Figure 10. Base-Emitter Temperature Coefficient 40 4.0 100 -1.0 Figure 9. Collector Saturation Region 20 50 Figure 8. "On" Voltage VB, TEMPERATURE COEFFICIENT (mV/ C) VCE , COLLECTOR-EMITTER VOLTAGE (VOLTS) Figure 7. DC Current Gain 10 20 2.0 5.0 IC, COLLECTOR CURRENT (mA) VCE = 5 V TA = 25C 500 200 100 50 20 1.0 5.0 10 50 100 IC, COLLECTOR CURRENT (mA) 100 Figure 11. Capacitance Figure 12. Current-Gain - Bandwidth Product http://onsemi.com 4 BC846AWT1 Series, BC847AWT1 Series, BC848AWT1 Series INFORMATION FOR USING THE SC-70/SOT-323 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection 0.025 0.65 0.025 0.65 0.075 1.9 0.035 0.9 0.028 0.7 inches mm SC-70/SOT-323 POWER DISSIPATION The power dissipation of the SC-70/SOT-323 is a function of the pad size. This can vary from the minimum pad size for soldering to the pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RJA, the thermal resistance from the device junction to ambient; and the operating temperature, TA. Using the values provided on the data sheet, PD can be calculated as follows. PD = the equation for an ambient temperature TA of 25C, one can calculate the power dissipation of the device which in this case is 200 milliwatts. PD = 150C - 25C 0.625C/W = 200 milliwatts The 0.625C/W assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 200 milliwatts. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, a higher power dissipation of 300 milliwatts can be achieved using the same footprint. TJ(max) - TA RJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into SOLDERING PRECAUTIONS * The soldering temperature and time should not exceed The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. * Always preheat the device. * The delta temperature between the preheat and soldering should be 100C or less.* * When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference should be a maximum of 10C. 260C for more than 10 seconds. * When shifting from preheating to soldering, the maximum temperature gradient should be 5C or less. * After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. * Mechanical stress or shock should not be applied during cooling * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. http://onsemi.com 5 BC846AWT1 Series, BC847AWT1 Series, BC848AWT1 Series SOLDER STENCIL GUIDELINES The stencil opening size for the surface mounted package should be the same as the pad size on the printed circuit board, i.e., a 1:1 registration. Prior to placing surface mount components onto a printed circuit board, solder paste must be applied to the pads. A solder stencil is required to screen the optimum amount of solder paste onto the footprint. The stencil is made of brass or stainless steel with a typical thickness of 0.008 inches. TYPICAL SOLDER HEATING PROFILE The line on the graph shows the actual temperature that might be experienced on the surface of a test board at or near a central solder joint. The two profiles are based on a high density and a low density board. The Vitronics SMD310 convection/infrared reflow soldering system was used to generate this profile. The type of solder used was 62/36/2 Tin Lead Silver with a melting point between 177-189C. When this type of furnace is used for solder reflow work, the circuit boards and solder joints tend to heat first. The components on the board are then heated by conduction. The circuit board, because it has a large surface area, absorbs the thermal energy more efficiently, then distributes this energy to the components. Because of this effect, the main body of a component may be up to 30 degrees cooler than the adjacent solder joints. For any given circuit board, there will be a group of control settings that will give the desired heat pattern. The operator must set temperatures for several heating zones, and a figure for belt speed. Taken together, these control settings make up a heating "profile" for that particular circuit board. On machines controlled by a computer, the computer remembers these profiles from one operating session to the next. Figure 7 shows a typical heating profile for use when soldering a surface mount device to a printed circuit board. This profile will vary among soldering systems but it is a good starting point. Factors that can affect the profile include the type of soldering system in use, density and types of components on the board, type of solder used, and the type of board or substrate material being used. This profile shows temperature versus time. STEP 1 PREHEAT ZONE 1 RAMP" 200C 150C STEP 5 STEP 4 HEATING HEATING ZONES 3 & 6 ZONES 4 & 7 SPIKE" SOAK" STEP 2 STEP 3 VENT HEATING SOAK" ZONES 2 & 5 RAMP" DESIRED CURVE FOR HIGH MASS ASSEMBLIES 205 TO 219C PEAK AT SOLDER JOINT 170C 160C 150C 140C 100C 100C 50C STEP 6 STEP 7 VENT COOLING SOLDER IS LIQUID FOR 40 TO 80 SECONDS (DEPENDING ON MASS OF ASSEMBLY) DESIRED CURVE FOR LOW MASS ASSEMBLIES TIME (3 TO 7 MINUTES TOTAL) TMAX Figure 13. Typical Solder Heating Profile http://onsemi.com 6 BC846AWT1 Series, BC847AWT1 Series, BC848AWT1 Series PACKAGE DIMENSIONS SC-70 (SOT-323) CASE 419-04 ISSUE L A L NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3 B S 1 2 D G C 0.05 (0.002) J N K H STYLE 3: PIN 1. BASE 2. EMITTER 3. COLLECTOR http://onsemi.com 7 DIM A B C D G H J K L N S INCHES MIN MAX 0.071 0.087 0.045 0.053 0.032 0.040 0.012 0.016 0.047 0.055 0.000 0.004 0.004 0.010 0.017 REF 0.026 BSC 0.028 REF 0.079 0.095 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.00 0.30 0.40 1.20 1.40 0.00 0.10 0.10 0.25 0.425 REF 0.650 BSC 0.700 REF 2.00 2.40 BC846AWT1 Series, BC847AWT1 Series, BC848AWT1 Series Notes Thermal Clad is a trademark of the Bergquist Company. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 8 BC846AWT1/D