High Voltage, Precision Difference Amplifier AD8208 Data Sheet FUNCTIONAL BLOCK DIAGRAM VS Qualified for automotive applications EMI filters included High common-mode voltage range -2 V to +45 V operating -24 V to +80 V survival Buffered output voltage Gain = 20 V/V Low-pass filter (1-pole or 2-pole) Wide operating temperature range -40C to +125C for WB grade -40C to +150C for WH grade Excellent ac and dc performance 1 mV voltage offset -5 ppm/C typical gain drift 80 dB CMRR minimum dc to 10 kHz A1 EMI FILTER +IN EMI FILTER -IN EMI FILTER A2 AD8208 + G = 10 - + G=2 - GND OUT 08714-001 FEATURES Figure 1. APPLICATIONS High-side current sensing Motor controls Solenoid controls Power management Low-side current sensing Diagnostic protection GENERAL DESCRIPTION The AD8208 is a single-supply difference amplifier ideal for amplifying and low-pass filtering small differential voltages in the presence of a large common-mode voltage. The input commonmode voltage range extends from -2 V to +45 V at a single +5 V supply. The AD8208 is qualified for automotive applications. The amplifier offers enhanced input overvoltage and ESD protection, and includes EMI filtering. Rev. C Automotive applications demand robust, precision components for improved system control. The AD8208 provides excellent ac and dc performance, minimizing errors in the application. Typical offset and gain drift in both the SOIC and MSOP packages are less than 5 V/C and 10 ppm/C, respectively. The device also delivers a minimum CMRR of 80 dB from dc to 10 kHz. The AD8208 features an externally accessible 100 k resistor at the output of the preamplifier (A1), which can be used for lowpass filtering and for establishing gains other than 20. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2010-2013 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD8208 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Applications Information .............................................................. 12 Applications ....................................................................................... 1 High-Side Current Sensing with a Low-Side Switch ............. 12 Functional Block Diagram .............................................................. 1 High-Rail Current Sensing ....................................................... 12 General Description ......................................................................... 1 Low-Side Current Sensing ........................................................ 12 Revision History ............................................................................... 2 Gain Adjustment ........................................................................ 13 Specifications..................................................................................... 3 Gain Trim .................................................................................... 13 Absolute Maximum Ratings............................................................ 5 Low-Pass Filtering ...................................................................... 14 ESD Caution .................................................................................. 5 High Line Current Sensing with LPF and Gain Adjustment 15 Pin Configuration and Function Descriptions ............................. 6 Outline Dimensions ....................................................................... 16 Typical Performance Characteristics ............................................. 7 Ordering Guide .......................................................................... 17 Theory of Operation ...................................................................... 11 Automotive Products ................................................................. 17 REVISION HISTORY 12/13-----Rev. B to Rev. C Changes to Table 1 ............................................................................ 3 Change to Table 2 ............................................................................. 5 Changes to Ordering Guide .......................................................... 17 2/13--Rev. A to Rev. B Changes to Features.......................................................................... 1 Changes to Table 1 ............................................................................ 3 Changes to Table 4 ............................................................................ 4 Moved Ordering Guide.................................................................. 16 Changes to Ordering Guide .......................................................... 16 Added Automotive Products Section .......................................... 16 5/10--Rev. 0 to Rev. A Added 8-Lead MSOP ........................................................ Universal Changes to Features Section and General Description Section ..1 Updated Outline Dimensions ....................................................... 15 Changes to Ordering Guide .......................................................... 15 1/10--Revision 0: Initial Version Rev. C | Page 2 of 20 Data Sheet AD8208 SPECIFICATIONS TOPR = -40C to +125C for AD8208WBR and AD8208WBRM grade, TOPR = -40C to +150C for AD8208WHR grade, TA = 25C, VS = 5 V, RL = 25 k (RL is the output load resistor), unless otherwise noted. Specifications applicable for both packages (SOIC and MSOP). Table 1. Parameter SYSTEM GAIN Initial Error vs. Temperature Gain Drift VOLTAGE OFFSET Initial Input Offset (Referred to Input [RTI]) Input Offset (RTI) Over Temperature Voltage Offset vs. Temperature INPUT Input Impedance Differential Common Mode VCM (Continuous) CMRR 2 PREAMPLIFIER (A1) Gain Gain Error Output Voltage Range Output Resistance OUTPUT BUFFER (A2) Gain Gain Error Output Voltage Range 4, 5 Output Voltage Range 6 Input Bias Current Output Resistance DYNAMIC RESPONSE System Bandwidth Slew Rate NOISE 0.1 Hz to 10 Hz Spectral Density, 1 kHz (RTI) POWER SUPPLY Operating Range Quiescent Current Quiescent Current vs. Temperature PSRR Test Conditions 1 Min Typ Max Unit 0 0.3 -20 V/V % ppm/C VCM = 0.15 V, TA VCM = 0 V, TOPR VCM = 0 V, TOPR -20 2 4 +20 mV mV V/C 440 220 +45 VCM = -2 V to +45 V, dc f = dc to 10 kHz, 3 TOPR 360 180 -2 80 80 k k V dB dB 20 0.075 V VOUT (VS - 0.1 V), dc, TOPR TOPR 400 200 100 10 0.05 V VOUT (VS - 0.1 V), dc, TOPR AD8208WBR, AD8208WBRM AD8208WHR, AD8208WHRM +0.3 VS - 0.1 VS - 0.1 103 V/V % V V k -0.3 +0.3 V/V % 0.075 0.1 VS - 0.1 VS - 0.12 V V 0.075 0.1 VS - 0.1 VS - 0.12 50 2 V V nA 70 1 kHz V/s 20 500 V p-p nV/Hz -0.3 0.0375 0.05 97 100 2 0.075 V VOUT (VS - 0.1 V), dc, TOPR RL = 25 k, differential Input (V) = 0 V, TOPR Pin 3 (A1 output) driving Pin 4 (A2 input) AD8208WBR, AD8208WBRM AD8208WHR, AD8208WHRM Pin 4 (A2 input) driven with external source AD8208WBR, AD8208WBRM AD8208WHR, AD8208WHRM TOPR RL = 1 k, frequency = dc VIN = 0.01 V p-p, VOUT = 0.14 V p-p VIN = 0.28 V, VOUT = 4 V step 4.5 Typical, TA VOUT = 0.1 V dc, VS = 5 V, TOPR AD8208WBR, AD8208WBRM AD8208WHR, AD8208WHRM VS = 4.5 V to 5.5 V, TOPR Rev. C | Page 3 of 20 5.5 V mA 2.7 3.0 mA mA dB 1.6 66 80 AD8208 Parameter TEMPERATURE RANGE Data Sheet Test Conditions 1 For Specified Performance at TOPR AD8208WBR, AD8208WBRM AD8208WHR, AD8208WHRM Min -40 -40 Typ Max Unit +125 +150 C C VCM = input common-mode voltage. Source imbalance < 2 . 3 The AD8208 preamplifier exceeds 80 dB CMRR at 10 kHz. However, because the output is available only by way of the 100 k resistor, even a small amount of pin-topin capacitance between the IN pins and the A1 and A2 pins might couple an input common-mode signal larger than the greatly attenuated preamplifier output. The effect of pin-to-pin coupling can be negated in all applications by using a filter capacitor from Pin 3 to GND. 4 The output voltage range of the AD8208 varies depending on the load resistance and temperature. For additional information on this specification, see Figure 12 and Figure 13. 5 The output voltage range of A2 assumes that Pin 3 (A1 output) and Pin 4 (A2 Input) are shorted together. A 25 k load resistor used for testing. 6 The output voltage range of A2 assumes Pin 4 (A2 Input) is driven with an external voltage source. A 25 k load resistor was used for testing. 1 2 Rev. C | Page 4 of 20 Data Sheet AD8208 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Voltage Continuous Input Voltage (Common Mode) Differential Input Voltage Reversed Supply Voltage Protection ESD Human Body Model Operating Temperature Range WBR and WBRM Grade WHR and WHRM Grade Storage Temperature Range Output Short-Circuit Duration Lead Temperature Range (Soldering, 10 sec) Rating 12 V -24 V to +80 V 12 V 0.3 V 4000 V -40C to +125C -40C to +150C -65C to +150C Indefinite 300C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. C | Page 5 of 20 AD8208 Data Sheet PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 8 2 6 3 A1 3 AD8208 TOP VIEW (Not to Scale) A2 4 +IN 7 NC 6 VS 5 OUT NC = NO CONNECT 4 5 08714-003 GND 2 8 08714-002 -IN 1 Figure 3. Metallization Photograph Figure 2. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 8 Mnemonic -IN GND A1 A2 OUT VS NC +IN Coordinates X Y -322 +563 -321 +208 -321 -51 -321 -214 +321 -388 +322 +363 +322 +561 Description Inverting Input Ground Preamplifier (A1) Output Buffer (A2) Input Buffer (A2) Output Supply No Connect Noninverting Input Rev. C | Page 6 of 20 Data Sheet AD8208 TYPICAL PERFORMANCE CHARACTERISTICS TOPR = -40C to +125C, TA = 25C, VS = 5 V, RL = 25 k (RL is the output load resistor), unless otherwise noted. 0.2 1500 0.1 1000 GAIN ERROR (ppm) -0.2 -0.3 500 0 -500 -1000 -0.5 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 -1500 -40 TEMPERATURE (C) 08714-004 -0.4 20 35 50 65 80 95 110 125 0.47 TOTAL INPUT BIAS CURRENT (mA) 25 20 15 10 5 0 -5 -10 0.42 0.37 0.32 0.27 0.22 0.17 0.12 0.07 0.02 -15 10k 100k FREQUENCY (Hz) 1M -0.03 08714-005 -20 1k -2 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 INPUT COMMON-MODE (V) Figure 5. Typical Small-Signal Bandwidth 08714-008 GAIN (dB) 5 Figure 7. Typical Gain Error vs. Temperature 30 Figure 8. Total Input Bias Current vs. Common-Mode Voltage, with +IN and -IN Pins Connected (Shorted) -35 120 +125C +25C A2 INPUT BIAS CURRENT (nA) 100 90 80 70 60 +25C -25 +125C -20 -15 -10 -5 0 50 100 1k 10k 100k FREQUENCY (Hz) 1M 5 08714-006 40 10 -40C -30 -40C CMRR (dB) -10 TEMPERATURE (C) Figure 4. Typical Offset Drift vs. Temperature 110 -25 08714-007 -0.1 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 A2 INPUT VOLTAGE (V) 08714-009 VOSI (mV) 0 Figure 9. Input Bias Current of A2 vs. Input Voltage and Temperature Figure 6. Typical CMRR vs. Frequency Rev. C | Page 7 of 20 Data Sheet 11.0 1.6 10.5 1.5 1.4 1.3 OUTPUT VOLTAGE RANGE (V) 10.0 9.5 9.0 8.5 8.0 7.5 7.0 6.5 6.0 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 -40C +25C +125C 0.4 0.3 0.2 0.1 5.5 08714-010 5.0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 TEMPERATURE (C) 0 0 1 2 3 4 5 6 7 OUTPUT SINK CURRENT (mA) 8 9 08714-013 MAXIMUM OUTPUT SINK CURRENT (mA) AD8208 10 Figure 13. Output Voltage Range from GND vs. Output Sink Current Figure 10. Maximum Output Sink Current vs. Temperature INPUT 5.8 5.5 100mV/DIV 2 OUTPUT 5.2 4.9 4.6 1V/DIV 4.0 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 140 08714-014 1 4.3 08714-011 MAXIMUM OUTPUT SOURCE CURRENT (mA) 6.1 TIME (2s/DIV) Figure 11. Maximum Output Source Current vs. Temperature Figure 14. Rise Time 4.9 OUTPUT VOLTAGE RANGE (V) 4.7 100mV/DIV 4.5 4.3 -40C 4.1 +25C +125C INPUT 2 3.9 1V/DIV 3.7 3.5 3.3 3.1 OUTPUT 2.9 2.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 OUTPUT SOURCE CURRENT (mA) 08714-012 2.7 TIME (2s/DIV) Figure 12. Output Voltage Range of A2 vs. Output Source Current Figure 15. Fall Time Rev. C | Page 8 of 20 08714-015 1 Data Sheet AD8208 2V/DIV 200mV/DIV 2 INPUT 2 0.01%/DIV 1 2V/DIV TIME (2s/DIV) 08714-019 OUTPUT 08714-016 1 TIME (20s/DIV) Figure 16. Differential Overload Recovery, Rising Figure 19. Settling Time, Falling 1200 +125C +25C -40C 1000 200mV/DIV 800 INPUT COUNT 2 600 2V/DIV 400 200 OUTPUT 0 -4 -3 Figure 17. Differential Overload Recovery, Falling -2 -1 0 VOS (mV) 1 2 3 4 10 15 20 08714-020 TIME (2s/DIV) 08714-017 1 Figure 20. Offset Distribution 400 350 300 2 2V/DIV COUNT 250 0.01%/DIV 1 200 150 100 0 -20 -15 -10 -5 0 5 OFFSET DRIFT (V/C) Figure 21. Offset Drift Distribution Figure 18. Settling Time, Rising Rev. C | Page 9 of 20 08714-021 TIME (20s/DIV) 08714-018 50 Data Sheet 2400 2100 2100 1800 1800 1500 1500 1200 1200 900 900 600 600 300 300 0 -15 -10 -5 0 5 GAIN DRIFT (ppm/C) 10 15 +125C +25C -40C 0 -0.3 -0.2 -0.1 0 0.1 GAIN ERROR (%) Figure 23. Gain Error Figure 22. Gain Drift Distribution Rev. C | Page 10 of 20 0.2 0.3 08714-037 COUNT 2400 08714-022 COUNT AD8208 Data Sheet AD8208 THEORY OF OPERATION The AD8208 is a single-supply difference amplifier typically used to amplify a small differential voltage in the presence of rapidly changing, high common-mode voltages. The AD8208 consists of two amplifiers (A1 and A2), a resistor network, a small voltage reference, and a bias circuit (not shown); see Figure 24. The set of input attenuators preceding A1 consists of RA, RB, and RC, which feature a combined series resistance of approximately 400 k 20%. The purpose of these resistors is to attenuate the input voltage to match the input voltage range of A1. This balanced resistor network attenuates the common-mode signal by a ratio of 1/14. The A1 amplifier inputs are held within the power supply range, even as Pin 1 and Pin 8 exceed the supply or fall below the common (ground). A reference voltage of 350 mV biases the attenuator above ground, allowing Amplifier A1 to operate in the presence of negative common-mode voltages. The input resistor network also attenuates normal (differential) mode voltages. Therefore, A1 features a gain of 140 V/V to provide a total system gain, from IN to the output of A1, equal to 10 V/V, as shown in the following equation: by connecting A1 to A2 and placing a capacitor to ground (see Figure 33). The value of RF1 and RF2 is 10 k, providing a gain of 2 V/V for Amplifier A2. When connecting Pin A1 and Pin A2 together, the AD8208 provides a total system gain equal to Total Gain of (A1 + A2) (V/V) = 10 (V/V) x 2 (V/V) = 20 V/V at the output of A2 (the OUT pin). The ratios of RA, RB, RC, and RF are trimmed to a high level of precision, allowing a typical CMRR value that exceeds 80 dB. This performance is accomplished by laser trimming the resistor ratio matching to better than 0.01%. -IN RA +IN VS RA - RF RB RG RC RC A2 RFILTER + + RB A1 A1 OUT A2 - RF1 RF RM RF2 A precision trimmed, 100 k resistor is placed in series with the output of Amplifier A1. The user has access to this resistor via an external pin (A1). A low-pass filter can be easily implemented Rev. C | Page 11 of 20 08714-023 350mV Gain (A1) = 1/14 (V/V) x 140(V/V) = 10 V/V GND Figure 24. Simplified Schematic AD8208 Data Sheet APPLICATIONS INFORMATION HIGH-SIDE CURRENT SENSING WITH A LOW-SIDE SWITCH HIGH-RAIL CURRENT SENSING In load control configurations for high-side current sensing with a low-side switch, the PWM-controlled switch is ground referenced. An inductive load (solenoid) connects to a power supply/battery. A resistive shunt is placed between the switch and the load (see Figure 25). An advantage of placing the shunt on the high side is that the entire current, including the recirculation current, is monitored because the shunt remains in the loop when the switch is off. In addition, shorts to ground can be detected with the shunt on the high side, enhancing the diagnostics of the control loop. In this circuit configuration, when the switch is closed, the commonmode voltage moves down to near the negative rail. When the switch is opened, the voltage reversal across the inductive load causes the common-mode voltage to be held one diode drop above the battery by the clamp diode. In the high-rail current-sensing configuration, the shunt resistor is referenced to the battery. High voltage is present at the inputs of the current-sense amplifier. When the shunt is battery referenced, the AD8208 produces a linear ground-referenced analog output. Additionally, the AD8214 can be used to provide an overcurrent detection signal in as little as 100 ns (see Figure 27). This feature is useful in high current systems where fast shutdown in overcurrent conditions is essential. OVERCURRENT DETECTION (<100ns) 5 6 7 8 OUT GND NC -IN AD8214 NC VREG +IN 4 3 2 VS 1 5V CLAMP DIODE CLAMP DIODE INDUCTIVE LOAD OUTPUT SHUNT +IN NC VS -IN + BATTERY GND - SHUNT AD8208 A1 A2 GND A1 1 8 2 7 3 AD8208 4 6 5 - +IN NC VS BATTERY INDUCTIVE LOAD 5V OUT SWITCH CF A2 08714-026 -IN + OUT SWITCH Figure 27. Battery-Referenced Shunt Resistor 08714-024 CF NC = NO CONNECT Figure 25. Low-Side Switch In cases where a high-side switch is used for PWM control of the load current in an application, the AD8208 can be used as shown in Figure 26. The recirculation current through the freewheeling diode (clamp diode) is monitored through the shunt resistor. In this configuration, the common-mode voltage in the application drops below GND when the FET is switched off. The AD8208 operates down to -2 V, providing an accurate current measurement. LOW-SIDE CURRENT SENSING In systems where low-side current sensing is preferable, the AD8208 provides a simple, high accuracy, integrated solution. In this configuration, the AD8208 rejects ground noise and offers high input to output linearity, regardless of the differential input voltage. INDUCTIVE LOAD 5V CLAMP DIODE SWITCH OUTPUT 5V +IN NC VS OUT SWITCH BATTERY OUTPUT +IN NC VS AD8208 SHUNT OUT + - SHUNT AD8208 -IN CLAMP DIODE GND A1 -IN GND A1 A2 CF A2 NC = NO CONNECT Figure 28. Ground-Referenced Shunt Resistor CF NC = NO CONNECT 08714-025 INDUCTIVE LOAD Figure 26. High-Side Switch Rev. C | Page 12 of 20 08714-027 BATTERY Data Sheet AD8208 4 mA to 20 mA Current Loop Receiver The AD8208 can also be used in low current-sensing applications, such as the 4 mA to 20 mA current loop receiver shown in Figure 29. In such applications, the relatively large shunt resistor may degrade the common-mode rejection. Adding a resistor of equal value on the low impedance side of the input corrects this error. used should be equal to 100 k minus the parallel sum of REXT and 100 k. For example, with REXT = 100 k (yielding a composite gain of 10 V/V), the optional offset nulling resistor is 50 k. Gains Greater than 20 Connecting a resistor from the output of the buffer amplifier to its noninverting input, as shown in Figure 31, increases the gain. The gain is now multiplied by the factor 5V REXT/(REXT - 100 k) 10 1% For example, it is doubled for REXT = 200 k. Overall gains as high as 50 are achievable in this way. Note that the accuracy of the gain becomes critically dependent on the resistor value at high gains. In addition, the effective input offset voltage at Pin 1 and Pin 8 (which is about six times the actual offset of A1) limits the use of the part in high gain, dc-coupled applications. OUTPUT +IN NC VS OUT + - BATTERY 10 1% AD8208 -IN GND A1 A2 5V OUTPUT 08714-028 NC = NO CONNECT +IN + VDIFF GAIN ADJUSTMENT REXT REXT = 100k GND A1 GAIN GAIN - 20 A2 - NC = NO CONNECT Because the preamplifier has an output resistance of 100 k, an external resistor connected from Pin 3 and Pin 4 to GND decreases the gain by the following factor (see Figure 30): REXT/(100 k + REXT) 5V Figure 31. Adjusting for Gains Greater than 20 GAIN TRIM Figure 32 shows a method for incremental gain trimming by using a trim potentiometer and an external resistor, REXT. The following approximation is useful for small gain ranges: G (10 M / REXT)% OUTPUT NC VS AD8208 20REXT REXT + 100k 5V - REXT = 100k GND A1 For example, using this equation, the adjustment range is 2% for REXT = 5 M and 10% for REXT = 1 M. OUT GAIN = -IN AD8208 20REXT REXT - 100k + VCM Gains Less than 20 + OUT - -IN The default gain of the preamplifier and buffer are 10 V/V and 2 V/V, respectively, resulting in a composite gain of 20 V/V. With the addition of external resistor(s) or trimmer(s), the gain can be lowered, raised, or finely calibrated. VDIFF VS GAIN = Figure 29. 4 mA to 20 mA Current Loop Receiver +IN NC 08714-030 CF GAIN 20 - GAIN OUTPUT A2 +IN NC VS OUT + REXT NC = NO CONNECT + VDIFF AD8208 - -IN GND A1 A2 Figure 30. Adjusting for Gains Less than 20 The overall bandwidth is unaffected by changes in gain by using this method, although there may be a small offset voltage due to the imbalance in source resistances at the input to the buffer. In many cases, this can be ignored, but if desired, the offset voltage can be nulled by inserting a resistor in series with Pin 4. The resistor Rev. C | Page 13 of 20 + VCM REXT GAIN TRIM 20k MIN - NC = NO CONNECT Figure 32. Incremental Gain Trimming 08714-031 - 08714-029 VCM AD8208 Data Sheet Internal Signal Overload Considerations When configuring the gain for values other than 20, the maximum input voltage with respect to the supply voltage and ground must be considered because either the preamplifier or the output buffer reaches its full-scale output (VS - 0.1 V) with large differential input voltages. The input of the AD8208 is limited to (VS - 0.1) / 10 for overall gains of 10 because the preamplifier, with its fixed gain of 10 V/V, reaches its full-scale output before the output buffer. For gains greater than 10, the swing at the buffer output reaches its full scale first and then limits the AD8208 input to (VS - 0.1) / G, where G is the overall gain. If the gain is raised using a resistor, as shown in Figure 31, the corner frequency is lowered by the same factor as the gain is raised. Therefore, using a resistor of 200 k (for which the gain would be doubled), results in a corner frequency scaled to 0.796 Hz F (0.039 F for a 20 Hz corner frequency). 5V OUTPUT +IN + VDIFF NC VS OUT C AD8208 - LOW-PASS FILTERING fC(Hz) = 1/C(F) -IN When implementing a filter, the PAR should be considered so that the output of the AD8208 preamplifier (A1) does not clip before A2; otherwise, the nonlinearity would be averaged and appear as an error at the output. To avoid this error, both amplifiers should clip at the same time. This condition is achieved when the PAR is no greater than the gain of the second amplifier (2 for the default configuration). For example, if a PAR of 5 is expected, the gain of A2 should be increased to 5. Low-pass filters can be implemented in several ways by using the features provided by the AD8208. In the simplest case, a single-pole filter (20 dB/decade) is formed when the output of A1 is connected to the input of A2 via the internal 100 k resistor by tying Pin 3 to Pin 4 and adding a capacitor from this node to ground, as shown in Figure 33. If a resistor is added across the capacitor to lower the gain, the corner frequency increases; therefore, gain should be calculated using the parallel sum of the resistor and 100 k. 5V + VCM A1 A2 255k - 08714-033 C NC = NO CONNECT Figure 34. Two-Pole, Low-Pass Filter A two-pole filter with a roll-off of 40 dB/decade can be implemented using the connections shown in Figure 34. This configuration is a Sallen-Key form based on a x2 amplifier. It is useful to remember that a two-pole filter with a corner frequency of f2 and a single-pole filter with a corner frequency of f1 have the same attenuation, that is, 40 log (f2/f1), as shown in Figure 35. Using the standard resistor value shown in Figure 34 and capacitors of equal values, the corner frequency is conveniently scaled to 1 Hz F (0.05 F for a 20 Hz corner frequency). A maximal flat response occurs when the resistor is lowered to 196 k, scaling the corner frequency to 1.145 Hz F. The output offset is raised by approximately 5 mV (equivalent to 250 V at the input pins). ATTENUATION In many transducer applications, it is necessary to filter the signal to remove spurious high frequency components, including noise, or to extract the mean value of a fluctuating signal with a peakto-average ratio (PAR) greater than unity. For example, a full-wave rectified sinusoid has a PAR of 1.57, a raised cosine has a PAR of 2, and a half-wave sinusoid has a PAR of 3.14. Signals with large spikes may have PARs of 10 or more. GND 40dB/DECADE 20dB/DECADE 40log (f2/f1) OUTPUT VS A 1-POLE FILTER, CORNER f1, AND A 2-POLE FILTER, CORNER f2, HAVE THE SAME ATTENUATION -40log (f2/f1) AT FREQUENCY f22/f1 OUT 1 + VDIFF NC fC = 2C105 AD8208 - f1 C IN FARADS f2 FREQUENCY -IN + A1 A2 Figure 35. Comparative Responses of Single-Pole and Two-Pole Low-Pass Filters CF - NC = NO CONNECT 08714-032 VCM GND f22/f1 08714-034 +IN Figure 33. Single-Pole, Low-Pass Filter Using the Internal 100 k Resistor Rev. C | Page 14 of 20 Data Sheet AD8208 diode regulates the common-mode potential applied to the device. For example, a battery spike of 20 V may result in an applied common-mode potential of 21.5 V to the input of the devices. HIGH LINE CURRENT SENSING WITH LPF AND GAIN ADJUSTMENT The circuit shown in Figure 36 is similar to Figure 25, but includes gain adjustment and low-pass filtering. To produce a full-scale output of 4 V, a gain of 40 V/V is used, adjustable by 5% to absorb the tolerance in the shunt. There is sufficient headroom to allow 10% overrange (to 4.4 V). The roughly triangular voltage across the sense resistor is averaged by a single-pole, low-pass filter that is set with a corner frequency of 3.6 Hz, which provides about 30 dB of attenuation at 100 Hz. A higher rate of attenuation can be obtained by using a two-pole filter with a corner frequency of 20 Hz, as shown in Figure 37. Although this circuit uses two separate capacitors, the total capacitance is less than half of what is needed for the single-pole filter. 5V INDUCTIVE LOAD OUTPUT 4V/AMP +IN NC VS OUT + BATTERY 191k - SHUNT AD8208 20k -IN GND A2 A1 SWITCH VOS/IB NULL NC = NO CONNECT 5% CALIBRATION RANGE fC(Hz) = 0.767Hz/C(F) (0.22F FOR fC = 3.6Hz) 5V 08714-035 C CLAMP DIODE Figure 36. High Line Current-Sensor Interface; Gain = 40 V/V, Single-Pole, Low-Pass Filter INDUCTIVE LOAD OUTPUT +IN NC VS OUT 432k + A power device that is either on or off controls the current in the load. The average current is proportional to the duty cycle of the input pulse and is sensed by a small-value resistor. The average differential voltage across the shunt is typically 100 mV, although its peak value is higher by an amount that depends on the inductance of the load and the control frequency. The commonmode voltage, on the other hand, extends from roughly 1 V above ground for the on condition to about 1.5 V above the battery voltage in the off condition. The conduction of the clamping BATTERY - SHUNT C AD8208 50k -IN GND A2 A1 SWITCH 127k C fC(Hz) = 1/C(F) (0.05F FOR fC = 20Hz) NC = NO CONNECT Rev. C | Page 15 of 20 Figure 37. Two-Pole Low-Pass Filter 08714-036 CLAMP DIODE AD8208 Data Sheet OUTLINE DIMENSIONS 5.00 (0.1968) 4.80 (0.1890) 8 4.00 (0.1574) 3.80 (0.1497) 5 1 4 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) 6.20 (0.2441) 5.80 (0.2284) 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) 0.31 (0.0122) COPLANARITY 0.10 SEATING PLANE 0.50 (0.0196) 0.25 (0.0099) 45 8 0 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) 012407-A COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 38. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) 3.20 3.00 2.80 8 3.20 3.00 2.80 1 5.15 4.90 4.65 5 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 0.85 0.75 15 MAX 1.10 MAX 0.40 0.25 6 0 0.23 0.09 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 39. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters Rev. C | Page 16 of 20 0.80 0.55 0.40 10-07-2009-B 0.15 0.05 COPLANARITY 0.10 Data Sheet AD8208 ORDERING GUIDE Model 1, 2 AD8208WBRZ AD8208WBRZ-R7 AD8208WBRZ-RL AD8208WBRMZ AD8208WBRMZ-R7 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C AD8208WBRMZ-RL -40C to +125C AD8208WHRZ AD8208WHRZ-RL AD8208WHRMZ AD8208WHRMZ-RL -40C to +150C -40C to +150C -40C to +150C -40C to +150C 1 2 Package Description 8-Lead SOIC_N 8-Lead SOIC_N, 7" Tape and Reel 8-Lead SOIC_N, 13" Tape and Reel 8-Lead Mini Small Outline Package [MSOP] 8-Lead Mini Small Outline Package [MSOP], 7" Tape and Reel 8-Lead Mini Small Outline Package [MSOP], 13" Tape and Reel 8-Lead SOIC_N 8-Lead SOIC_N, 13" Tape and Reel 8-Lead Mini Small Outline Package [MSOP] 8-Lead Mini Small Outline Package [MSOP], 13" Tape and Reel Package Option R-8 R-8 R-8 RM-8 RM-8 Branding RM-8 Y2F R-8 R-8 RM-8 RM-8 Y52 Y52 Y2F Y2F Z = RoHS Compliant Part. W = Qualified for Automotive Applications. AUTOMOTIVE PRODUCTS The AD8208W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. C | Page 17 of 20 AD8208 Data Sheet NOTES Rev. C | Page 18 of 20 Data Sheet AD8208 NOTES Rev. C | Page 19 of 20 AD8208 Data Sheet NOTES (c)2010-2013 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08714-0-12/13(C) Rev. C | Page 20 of 20