Transient Voltage Suppression Diodes Surface Mount - 1500W > SMCJ-HR series SMCJ-HR Series RoHS Description TVS Diode Arrays (SPATM Family of Products) Uni-directional The SMCJ-HR High Reliability series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Bi-directional Agency Approvals AGENCY Features * For surface mounted applications in order to optimize board space * Low profile package * Built-in strain relief *V BR @TJ= VBR@25C x (1+T AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter x (TJ - 25)) Symbol Value Unit Peak Pulse Power Dissipation at TA=25C by 10/1000s waveform (Fig.1)(Note 1), (Note 2) PPPM 1500 W Power Dissipation on infinite heat sink at TA=50OC PM(AV) 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 200 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional only (Note 4) VF 3.5/5.0 V TJ , TSTG -55 to 150 C Typical Thermal Resistance Junction to Lead RuJL 15 C/W Typical Thermal Resistance Junction to Ambient RuJA 75 C/W Operating Junction and Storage Temperature Range (T:Temperature Coefficient) * Glass passivated chip junction * 1500W peak pulse power capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * Fast response time: typically less than 1.0ps from 0V to BV min * Excellent clamping capability * Low incremental surge resistance * Typical IR less than 1A above 12V * High Temperature soldering guaranteed: 260C/40 seconds at terminals * Plastic package has Underwriters laboratory flammability 94V-O * Meet MSL level1, per J-STD-020, LF maximun peak of 260C * Matte tin lead-free plated * Halogen free and RoHS compliant Applications TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25OC per Fig. 2. 2. Mounted on copper pad area of 0.31x0.31" (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Functional Diagram Bi-directional Cathode Anode Uni-directional SMCJ-HR Series 1 41 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/22/13 Transient Voltage Suppression Diodes Surface Mount - 1500W > SMCJ-HR series Electrical Characteristics TVS Diode Arrays (SPATM Family of Products) Part Number (Uni) Part Number (Bi) SMCJ5.0A-HR SMCJ6.0A-HR SMCJ6.5A-HR SMCJ7.0A-HR SMCJ7.5A-HR SMCJ8.0A-HR SMCJ8.5A-HR SMCJ9.0A-HR SMCJ10A-HR SMCJ11A-HR SMCJ12A-HR SMCJ13A-HR SMCJ14A-HR SMCJ15A-HR SMCJ16A-HR SMCJ17A-HR SMCJ18A-HR SMCJ20A-HR SMCJ22A-HR SMCJ24A-HR SMCJ26A-HR SMCJ28A-HR SMCJ30A-HR SMCJ33A-HR SMCJ36A-HR SMCJ40A-HR SMCJ43A-HR SMCJ45A-HR SMCJ48A-HR SMCJ51A-HR SMCJ54A-HR SMCJ58A-HR SMCJ60A-HR SMCJ64A-HR SMCJ70A-HR SMCJ75A-HR SMCJ78A-HR SMCJ85A-HR SMCJ90A-HR SMCJ100A-HR SMCJ110A-HR SMCJ120A-HR SMCJ130A-HR SMCJ150A-HR SMCJ160A-HR SMCJ170A-HR SMCJ5.0CA-HR SMCJ6.0CA-HR SMCJ6.5CA-HR SMCJ7.0CA-HR SMCJ7.5CA-HR SMCJ8.0CA-HR SMCJ8.5CA-HR SMCJ9.0CA-HR SMCJ10CA-HR SMCJ11CA-HR SMCJ12CA-HR SMCJ13CA-HR SMCJ14CA-HR SMCJ15CA-HR SMCJ16CA-HR SMCJ17CA-HR SMCJ18CA-HR SMCJ20CA-HR SMCJ22CA-HR SMCJ24CA-HR SMCJ26CA-HR SMCJ28CA-HR SMCJ30CA-HR SMCJ33CA-HR SMCJ36CA-HR SMCJ40CA-HR SMCJ43CA-HR SMCJ45CA-HR SMCJ48CA-HR SMCJ51CA-HR SMCJ54CA-HR SMCJ58CA-HR SMCJ60CA-HR SMCJ64CA-HR SMCJ70CA-HR SMCJ75CA-HR SMCJ78CA-HR SMCJ85CA-HR SMCJ90CA-HR SMCJ100CA-HR SMCJ110CA-HR SMCJ120CA-HR SMCJ130CA-HR SMCJ150CA-HR SMCJ160CA-HR SMCJ170CA-HR UNI BI Reverse Stand off Voltage VR (Volts) GDE GDG GDK GDM GDP GDR GDT GDV GDX GDZ GEE GEG GEK GEM GEP GER GET GEV GEX GEZ GFE GFG GFK GFM GFP GFR GFT GFV GFX GFZ GGE GGG GGK GGM GGP GGR GGT GGV GGX GGZ GHE GHG GHK GHM GHP GHR BDE BDG BDK BDM BDP BDR BDT BDV BDX BDZ BEE BEG BEK BEM BEP BER BET BEV BEX BEZ BFE BFG BFK BFM BFP BFR BFT BFV BFX BFZ BGE BGG BGK BGM BGP BGR BGT BGV BGX BGZ BHE BHG BHK BHM BHP BHR 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 Marking Breakdown Voltage VBR (Volts) @ IT MIN MAX 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 Maximum Maximum Maximum Test Agency Peak Reverse Current Clamping Approval Voltage VC Pulse Leakage IR IT @ Ipp Current Ipp @ VR (mA) (V) (A) (A) 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 163.0 145.7 134.0 125.0 116.3 110.3 104.2 97.4 88.3 82.5 75.4 69.8 64.7 61.5 57.7 54.4 51.4 46.3 42.3 38.6 35.7 33.1 31.0 28.2 25.9 23.3 21.7 20.6 19.4 18.2 17.3 16.1 15.5 14.6 13.3 12.4 11.9 11.0 10.3 9.3 8.5 7.8 7.2 6.2 5.8 5.5 800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Note: 1. For bidirectional type having VR of 10 volts and less, the IR limit is double. 2. 100% High Temperature Storage Life test and Reflow Simulation. 3. 100% HTRB(High Temperature Reverse Bias). For Unidirectional, 150C/100%VR/96hours, for Bidirectional, 150C/100%VR/192hrs(96hours for each direction for Bidirectional). 4. Each lot of parts will pass group B test requirement. SMCJ-HR Series 2 42 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/22/13 Transient Voltage Suppression Diodes Surface Mount - 1500W > SMCJ-HR series Group B Test Requirement Screen Method Condition Requirement TM TVS Diode Arrays (SPA Family of Products) Surge test 10/1000 s Peak Pluse Waveform Maximum Clamping Voltage (VC) @ Peak Plus Current (IPP) Sample size 45 perform 10x Accept 0 failures Burn - In (HTRB) MIL -STD-750, Method 1038.5 Applied Voltage 100% VR@150C Sample size 45 340 hours (680 hours for bi-direction products, each direction 340 hours) Accept 0 failures IR@VR, V(BR)@IT Sample size 45 Accept 0 failures Electrical test -- I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT Ipp PPPM VR VBR VC IR VF IT IR IR IT VR VBR Vc V Ipp Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum current that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 10 0.31x0.31" (8.0x8.0mm) Copper Pad Area 1 0.000001 0.00001 0.0001 0.001 td-Pulse Width (sec.) Time continues on next page. SMCJ-HR Series 3 43 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/22/13 Transient Voltage Suppression Diodes Surface Mount - 1500W > SMCJ-HR series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A TVS Diode Arrays (SPATM Family of Products) Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 tr=10sec TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 0 175 TA-Ambient temperature (C) 10/1000sec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 6 - Steady State Power Dissipation Derating Curve Figure 5 - Typical Junction Capacitance Bi-directional V=0V 10000 Cj (pF) PM(AV), Steady Sate Power Dissipation (W) 100000 Uni-directional V=0V 1000 Uni-directional @VR 100 Bi-directional @VR 10 Tj=25C f=1.0MHz Vsig=50mVp-p 1 1.0 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 25 50 75 100 125 150 TA - Ambient Temperature (C) 175 IFSM - Peak Forward Surge Current (A) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only 200 180 160 140 120 100 80 60 40 20 0 1 10 100 Number of Cycles at 60 Hz SMCJ-HR Series 4 44 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/22/13 Transient Voltage Suppression Diodes Surface Mount - 1500W > SMCJ-HR series Soldering Parameters TVS Diode Arrays (SPATM Family of Products) Lead-free assembly Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25C t 25C to Peak Time (t) Environmental Specifications Physical Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Thermal Shock JESD22-A106 Weight 0.007 ounce, 0.21 grams Case JEDEC DO214AB. Molded plastic body over glass passivated junction MSL JEDEC-J-STD-020C, Level 1 Polarity Color band denotes positive end (cathode) except Bidirectional. H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102D RSH JESD22-B106C Dimensions DO-214AB (SMC J-Bend) Dimensions Cathode Band (for Uni-directional products only) C A B H D F E G J K L I Inches Min Millimeters Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F 0.002 0.008 0.051 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 - 4.200 L 0.094 - 2.400 - Solder Pads (all dimensions in mm) SMCJ-HR Series 5 45 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/22/13 Transient Voltage Suppression Diodes Surface Mount - 1500W > SMCJ-HR series Part Numbering System SMCJ XXX C A -HR Part Marking System TVS Diode Arrays (SPATM Family of Products) F Cathode Band HIGH RELIABILITY 5% VOLTAGE TOLERANCE XXXX YMXXX BI-DIRECTIONAL VOLTAGE SERIES Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Part number Component Package SMCJxxxXX-HR DO-214AB Packaging Option Quantity 500 Tape & Reel - 16mm/7" tape Packaging Specification EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 (8.0) 0.059 DIA (1.5) Cover tape 7.0 (187) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) SMCJ-HR Series Dimensions are in inches (and millimeters). Direction of Feed 6 46 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/22/13