G5V-2-H1 48DC - OMRON ELECTRONIC COMPONENTS

Low Signal Relay G5V-2 77

Low Signal Relay

G5V-2

Miniature Relay for Signal Circuits

• Suitable for handling low signals in computer peripherals,

telecommunications and security equipment.

• Capable of switching loads 10μA to 2 A.

• Conforms to FCC part 68 1,500 V surge withstand.

• Reliable Ag + Au-clad, bifurcated crossbar contacts.

• Fully-sealed construction.

• RoHS Compliant.

FCC

Ordering Information

To Order: Select the part number and add the desired coil voltage rating (e.g., G5V-2-DC12).

Model Number Legend

Specifications

■Contact Data

Note: P level: λ60 = 0.1 x 10–6/operation

This value was measured at a switching frequency of 120 operations/min and the criterion of contact resistance is 50 Ω. This value may vary

depending on the switching frequency and operating environment. Always double-check relay suitability under actual operating conditions.

Type Contact form Construction Model

Standard DPDT Fully-sealed G5V-2

High-sensitivity G5V-2-H1

1. Contact Form

2: DPDT

2. Coil type

Blank: Standard

H1: High-sensitivity

3. Rated Coil Voltage

3, 5, 6, 9, 12, 24, 48 VDC

G5V - - DC

1 32

Item Standard High-sensitivity

Load Resistive load (p.f. = 1)

Rated load 0.50 A at 125 VAC

2 A at 30 VDC

0.5 A at 125 VAC

1 A at 24 VDC

Contact material Ag (Au clad)

Carry current 2 A

Max. operating voltage 125 VAC

125 VDC

Max. operating current 2 A 1 A

Max. switching capacity 62.5 VA

60W

62.5 VA

24W

Min. permissible load (See note) 10 μA, 10 mVDC

78 Low Signal Relay G5V-2

■Coil Data

Standard Type

High-sensitivity Type

Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%.

2. The operating characteristics are measured at a coil temperature of 23°C.

3. The maximum voltage is the highest voltage that can be imposed on the relay coil.

Characteristics

Note: 1. The contact resistance was measured with 10 mA at 1 VDC with a fall-of-potential method.

2. Values in parentheses are typical values unless otherwise stated.

The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those for checking the dielectric strength.

4. The above values are initial values.

Rated voltage

(VDC)

Rated current

(mA)

Coil

resistance

(Ω)

Coil inductance

(Ref. value) (H)

Pick-up

voltage

Dropout

voltage

Maximum

voltage

Power

consumption

(mW)

Armature OFF Armature ON % of rated voltage

3 166.70 18 0.04 0.05 75% max. 5% min. 120% max.

at 23°C

Approx. 500

5 100 50 0.09 0.11

6 83.30 72 0.16 0.19

9 55.60 162 0.31 0.49

12 41.70 288 0.47 0.74

24 20.80 1,152 1.98 2.63

48 12 4,000 7.23 10.00 Approx. 580

Rated voltage

(VDC)

Rated current

(mA)

Coil

resistance

(Ω)

Coil inductance

(Ref. value) (H)

Pick-up

voltage

Dropout

voltage

Maximum

voltage

Power

consumption

(mW)

Armature OFF Armature ON % of rated voltage

3 50 60 0.18 0.57 75% max. 5% min. 180% max.

at 23°C

Approx. 150

5 30 166.7 0.46 0.71

6 25 240 0.70 0.97

9 16.70 540 1.67 2.33

12 12.50 960 2.90 3.99

24 8.33 2,880 6.72 9.27 Approx. 200

48 6.25 7,680 20.10 26.70 150% max.

at 23°C

Approx. 300

Contact resistance (See note 1) 50 mΩ max. (G5V-2); 100 mΩ max. (G5V-2-H1)

Operate time (See note 2) 7 ms max. (mean value: approx. 3.5 ms)

Release time (See note 2) 3 ms max. (mean value: approx. 0.8 ms)

Operating frequency

(max.)

Mechanical 36,000 operations/hour

Electrical 1,800 operations/hour (under rated load)

Insulation resistance (See note 3) 1,000 MΩ min (at 500 VDC)

Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between coil and contacts

1,000 VAC, 50/60 Hz for 1 minute between contacts of different poles

750 VAC, 50/60 Hz for 1 minute between contacts of same poles

(500 VAC, 50/60 Hz for 1 minute between contacts of same poles for high-sensitive type)

Surge withstand voltage 1,500 V (10 X 160 μs) between coil and contacts (conforms to part 68 of FCC rules)

Vibration Mechanical durability 10 to 55 Hz, 1.50 mm double amplitude

Malfunction

durability

Shock Mechanical durability 1,000 m/s2 (approx. 100 G)

Malfunction

durability 200 m/s2 (approx. 20 G), 100 m/s2 (approx. 10 G) for high-sensitive type

Ambient temperature Operating/storage -25° to 70°C (“-H1” versions) with no icing

-25° to 65°C (standard versions) with no icing

Humidity 5% to 85% RH

Service life Mechanical 15 million operations min. (at operating frequency of 36,000 operations/hour)

Electrical 100,000 operations min. (at 1,800 operations/hr). See “Characteristic Data”

Weight Approx. 5 g

Low Signal Relay G5V-2 79

■Characteristic Data

G5V-2

G5V-2-H1

Maximum Switching Capacity Ambient Temperature vs.

Maximum Coil Voltage

Electrical Service Life

Rated operating current (A)

Rated operating voltage (V) Rated operating current (A)

Service Life (x10 operations)

Ambient temperature (°)

Maximum coil voltage (%)

Coil rated voltage

3 to 24 VDC

48 VDC

30-VDC

resistive

load

125-VAC resistive

load

123

AC resistive load

resistive

load

Note: The maximum coil voltage refers to the maximum value in a varying range of operating

power voltage, not a continuous voltage.

Maximum Switching Capacity Ambient Temperature vs.

Maximum Coil Voltage

Electrical Service Life

Rated operating current (A)

Rated operating voltage (V) Rated operating current (A)

Service life (x10 operations)

Ambient temperature (°)

Maximum coil voltage (%)

AC resistive

load

DC resistive load

0.7

0.5

0.3

0.2

0.1

24-VDC resistive load

125-VAC resistive load

1000

500

300

100

3 to 24 VDC

48 VDC

200

180

160

140

120

100

Note: The maximum coil voltage refers to the maximum value in a varying range of operating

power voltage, not a continuous voltage.

80 Low Signal Relay G5V-2

Dimensions

Note: 1. All units are in millimeters unless otherwise indicated.

2. Tolerance: ±0.1

3. Orientation marks are indicated as follows:

G5V-2, G5V-2-H1

■Approvals

UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C

Note: 1.

The rated values approved by each of the safety standards may be different from the performance characteristics individually defined in this catalog.

2. In the interest of product improvement, specifications are subject to change.

Precautions

Long-term Continuously ON Contacts

Using the Relay in a circuit where the Relay will be ON continuously

for long periods (without switching) can lead to unstable contacts

because the heat generated by the coil itself will affect the insulation,

causing a film to develop on the contact surfaces. Be sure to use a

fail-safe circuit design that provides protection against contact failure

or coil burnout.

Relay Handling

When washing the product after soldering the Relay to a PCB, use a

water-based solvent or alcohol-based solvent, and keep the solvent

temperature to less than 40°C. Do not put the Relay in a cold clean-

ing bath immediately after soldering.

Type Contact form Coil rating Contact ratings

G5V-2 DPDT 3 to 48 VDC 0.6 A at 125 VAC (General Use)

0.6 A at 110 VDC (Resistive)

2 A at 30 VDC (Resistive)

G5V-2-H1 3 to 48 VDC 0.5 A at 125 VAC (General Use)

0.2 A at 110 VDC (Resistive)

1 A at 24 VDC (Resistive)

Terminal Arrangement/

Internal Connections

(Bottom View)

Mounting Holes

(Bottom View)

Tolerance: ±0.1

20.5 max.

20.3 typ.

10.1 max.

9.9 typ.

11.5 max.

11.4 typ.

0.5

3.5

7.62

0.30.5

7.62 5.08 5.08

(1.3)

7.62

(1.3)

Eight, 1-dia. holes

(1.2)

Low Signal Relay G5V-2

Omron Electronic Components, LLC

Terms and Conditions of Sales

1. Definitions: The words used herein are defined as follows.

(a) Terms: These terms and conditions

(b) Seller: Omron Electronic Components LLC and its subsidiaries

(d) Products: Products and/or services of Seller

(e) Including: Including without limitation

2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments,

invoices, purchase orders and other documents, whether electronic or in writing, relating

to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's

purchase order or other documents which are inconsistent with, or in addition to, these

Ter ms .

3. Distributor: Any distributor shall inform its customer of the contents after and including

section III of these Terms.

1. Prices; Payment: All prices stated are current, subject to change without notice by Seller.

Buyer agrees to pay the price in effect at the time the purchase order is accepted by

Seller. Payments for Products received are due net 30 days unless otherwise stated in

the invoice. Buyer shall have no right to set off any amounts against the amount owing in

respect of this invoice.

2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to

Buyer after deducting transportation charges, taxes and duties, and will be allowed only

if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past

due amounts owing to Seller.

3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum

legal rate, whichever is less, on any balance not paid within the stated terms.

4. Orders: Seller will accept no order less than 200 U.S. dollars net billing.

5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer

shall make remittance to Seller at the then current exchange rate most favorable to

Seller; provided that if remittance is not made when due, Buyer will convert the amount

to U.S. dollars at the then current exchange rate most favorable to Seller available

during the period between the due date and the date remittance is actually made.

6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining

any government approvals regarding the importation or sale of the Products.

7. Taxes: All taxes, duties and other governmental charges (other than general real

property and income taxes), including any interest or penalties thereon, imposed directly

or indirectly on Seller or required to be collected directly or indirectly by Seller for the

manufacture, production, sale, delivery, importation, consumption or use of the Products

sold hereunder (including customs duties and sales, excise, use, turnover and license

taxes) shall be charged to and remitted by Buyer to Seller.

8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller,

Seller reserves the right to stop shipments or require satisfactory security or payment in

advance. If Buyer fails to make payment or otherwise comply with these Terms or any

related agreement, Seller may (without liability and in addition to other remedies) cancel

any unshipped portion of Products sold hereunder and stop any Products in transit until

Buyer pays all amounts, including amounts payable hereunder, whether or not then due,

which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid

accounts.

9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer

indemnifies Seller fully against all costs or expenses arising in connection therewith.

10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from

causes beyond its control, including earthquakes, fires, floods, strikes or other labor

disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots,

delay in or lack of transportation or the requirements of any government authority.

11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller:

(a) All sales and shipments of Products shall be FOB shipping point (unless otherwise

stated in writing by Seller), at which point title to and all risk of loss of the Products

shall pass from Seller to Buyer, provided that Seller shall retain a security interest in

the Products until the full purchase price is paid by Buyer;

(b) Delivery and shipping dates are estimates only; and

handling and extra charges apply to special conditions.

12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products

occurring before delivery to the carrier or any claim related to pricing or other charges

must be presented in detail in writing to Seller within 30 days of receipt of shipment.

1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY

OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE

APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING

APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE

BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC

COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E)

SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT.

Buyer acknowledges that it alone has determined that the Products will meet their

requirements of the intended use in all cases. Buyer must know and observe all

prohibitions of use applicable to the Product/s.

2. Use with Attention: The followings are some examples of applications for which

particular attention must be given. This is not intended to be an exhaustive list of all

possible use of any Product, nor to imply that any use listed may be suitable for any

Product:

(a) Outdoor use, use involving potential chemical contamination or electrical

interference.

(b) Use in consumer Products or any use in significant quantities.

medical equipment, amusement machines, vehicles, safety equipment, and

installations subject to separate industry or government regulations.

(d) Systems, machines, and equipment that could present a risk to life or property.

3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING

SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM

AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE

PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE

WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED

VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY

SELLER.

5. Programmable Products: Seller shall not be responsible for the Buyer's programming of

a programmable Product.

1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in

materials and workmanship for a period of twelve months from the date of sale by Seller

(or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY

OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES,

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE OF THE PRODUCTS.

2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form

originally shipped with Buyer responsible for labor charges for removal or replacement

thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an

amount equal to the purchase price of the Product; provided that there shall be no

liability for Seller or its affiliates unless Seller's analysis confirms that the Products were

correctly handled, stored, installed and maintained and not subject to contamination,

abuse, misuse or inappropriate modification. Return of any Products by Buyer must be

approved in writing by Seller before shipment.

3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED

WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,

WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL

LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF

THE PRODUCT ON WHICH LIABILITY IS ASSERTED.

4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its

employees from and against all liabilities, losses, claims, costs and expenses (including

attorney's fees and expenses) related to any claim, investigation, litigation or proceeding

(whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or

omissions under these Terms or in any way with respect to the Products.

1. Intellectual Property: The intellectual property embodied in the Products is the exclusive

property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way

without the written permission of Seller. Buyer (at its own expense) shall indemnify and

hold harmless Seller and defend or settle any action brought against Seller to the extent

that it is based on a claim that any Product made to Buyer specifications infringed

intellectual property rights of another party.

2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or

tooling, all engineering and tooling shall remain the exclusive property of Seller. All

information and materials supplied by Seller to Buyer relating to the Products are

confidential and proprietary, and Buyer shall limit distribution thereof to its trusted

employees and strictly prevent disclosure to any third party.

3. Performance Data: Performance data is provided as a guide in determining suitability

and does not constitute a warranty. It may represent the result of Seller's test conditions,

and the users must correlate it to actual application requirements.

4. Change In Specifications: Product specifications and descriptions may be changed at

any time based on improvements or other reasons. It is Seller’s practice to change part

numbers when published ratings or features are changed, or when significant

engineering changes are made. However, some specifications of the Product may be

changed without any notice.

5. Errors And Omissions: The information on Seller’s website or in other documentation

has been carefully checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses

regarding (a) export of the Products or information provided by Seller; (b) sale of

Products to forbidden or other proscribed persons or organizations; (c) disclosure to non-

citizens of regulated technology or information.

1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing

between Buyer and Seller shall operate as a waiver of rights by Seller.

2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent.

3. Law: These Terms are governed by Illinois law (without regard to conflict of laws).

Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any

dispute hereunder.

4. Amendment: These Terms constitute the entire agreement between Buyer and Seller

relating to the Products, and no provision may be changed or waived unless in writing

signed by the parties.

5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall

not invalidate any other provision.

I. GENERAL

II. SALES

III. PRECAUTIONS

IV. WARRANTY AND LIMITATION

V. INFORMATION; ETC.

VI. MISCELLANEOUS

Low Signal Relay G5V-2

Certain Precautions on Specifications and Use

1. Suitability for Use. Seller shall not be responsible for conformity with any stan-

dards, codes or regulations which apply to the combination of the Product in

Buyer's application or use of the Product. At Buyer's request, Seller will pro-

vide applicable third party certification documents identifying ratings and limi-

tations of use which apply to the Product. This information by itself is not

sufficient for a complete determination of the suitability of the Product in com-

bination with the end product, machine, system, or other application or use.

Buyer shall be solely responsible for determining appropriateness of the par-

ticular Product with respect to Buyer's application, product or system. Buyer

shall take application responsibility in all cases but the following is a non-

exhaustive list of applications for which particular attention must be given:

(i) Outdoor use, uses involving potential chemical contamination or electrical

interference, or conditions or uses not described in this document.

(ii) Energy control systems, combustion systems, railroad systems, aviation

systems, medical equipment, amusement machines, vehicles, safety

equipment, and installations subject to separate industry or government

regulations.

(iii) Use in consumer products or any use in significant quantities.

(iv) Systems, machines and equipment that could present a risk to life or

property. Please know and observe all prohibitions of use applicable to this

product.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS

RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM

AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT

THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE

INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

2. Programmable Products. Seller shall not be responsible for the user's pro-

gramming of a programmable product, or any consequence thereof.

3. Performance Data. Performance data given in this publication is provided as

a guide for the user in determining suitability and does not constitute a war-

ranty. It may represent the result of Seller's test conditions, and the users must

correlate it to actual application requirements. Actual performance is subject to

Seller's Warranty and Limitations of Liability.

4. Change in Specifications. Product specifications and accessories may be

changed at any time based on improvements and other reasons. It is our prac-

tice to change part numbers when published ratings or features are changed,

or when significant construction changes are made. However, some specifica-

tions of the Product may be changed without any notice. When in doubt, spe-

cial part numbers may be assigned to fix or establish key specifications for

your application. Please consult with your Seller representative at any time to

confirm actual specifications of purchased Product.

5. Errors and Omissions. The information in this publication has been carefully

checked and is believed to be accurate; however, no responsibility is assumed

for clerical, typographical or proofreading errors, or omissions.

6. RoHS Compliance. Where indicated, our products currently comply, to the

best of our knowledge as of the date of this publication, with the requirements

of the European Union's Directive on the Restriction of certain Hazardous

Substances ("RoHS"), although the requirements of RoHS do not take effect

until July 2006. These requirements may be subject to change. Please consult

our website for current information.

OMRON ON-LINE

Global - http://www.omron.com

USA - http://www.components.omron.com

Cat. No. X301-E-1 Printed in USA

OMRON ELECTRONIC

COMPONENTS LLC

55 E. Commerce Drive, Suite B

Schaumburg, IL 60173

847-882-2288

06/09 Specifications subject to change without notice

Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website

at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.