REF01AZ/883B - Maxim Integrated Products, Inc.

SCOPE: PRECI SION REFERENCE +10 VOLT ADJUSTABLE OUTPU T

Device Type Generic Number

01 REF01A(x)/883B

02 REF01(x)/883B

Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows:

Outline Letter Mil-Std-1835 Case Outline Package Code

MAXIM SMD

Z P GDIP1-T8 or CDIP2-T8 8 LEAD CERDIP J8

J G MACY1-X8 8 LEAD CAN G99

RC 2 CQCC1-N20 20 Pin Ceramic LCC L20

Absolute Maximum Rati ngs

Supply Voltage VDD to GND ................................................................................... 40V

Output Short Circuit Duration (to GND or VIN) ............................................... Indefinite

Lead Temperature (soldering, 10 seconds) ............................................................... +300°C

Storage Temperature .................................................................................. -65°C to +150 °C

Continuous Po wer Dissipation .............................................................................TA=+70°C

8 lead CERDIP(derate 8.0mW/°C above +70°C) .................................................... 640mW

8 pin CAN (derate 6.67mW/°C above +70°C)......................................................... 533mW

20-Pin LCC (derate 9.09mW/°C above +70°C) ...................................................... 727mW

Junct ion Temperature TJ ....................................................................................... +150°C

Thermal Resista nce, J unction to Case, ΘJC:

Case Outline 8 lead CERDIP.................................................................. 55°C/W

Case Outline 8 lead CAN ....................................................................... 45°C/W

Case Outline 20-Pin LCC ....................................................................... 20°C/W

Thermal Resistance, Junction to Ambient, ΘJA:

Case Outline 8 lead CERDIP................................................................. 125°C/W

Case Outline 8 lead CAN ...................................................................... 150°C/W

Case Outline 20-Pin LCC ..................................................................... 110°C/W

Recommended Operating Conditions.

VOUT @ 25°C for device 01 ............................................................................ 5V ±15mV

VOUT @ 25°C for device 02 ............................................................................ 5V ±25mV

Ambient Operating Range (TA) ........................................................... -55°C to +125°C

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage

to the device. These are stress ratings only, and functional operation of the device at these or any

other conditions beyond those indicated in the ope ratio nal sections of the specifications is not

implied. Exposure to absolute maximum rating conditions for extended periods may affect

device reliability.

---------------------------- Electrical Characteristics of REF01 & 01A/883B 19-0490 Rev. C

for /883B and SMD 5962-89581 Page 2 of 6

TABLE 1 ELECTRICAL TESTS

TEST Symbol CONDITIONS

-55 °C ≤TA≤ +125°C

VDD=+15V, VIN=+15V

Unless otherwise specified

Group A

Subgroup Device t ype Limits

Min Limits

Max Units

Quiescent Supply

Current IIN No load 1

2,3 All 1.4

2.0 mA

Output Adjustment

Range ∆VTRIM RP=10kΩ1 All -3.0 +3.0 %

Output Voltage VOIL=0mA 1

2,3 01 9.97

9.95 10.03

10.04 V

Output Voltage VOIL=0mA 1

2,3 02 9.95

9.905 10.05

10.095 V

Short Circuit

Current ISC VO=0 1 All +15 +60 mA

Sink Current IS1All -0.3 mA

Load Regulation

NOTES 1, 2, 3 LD reg IL=0 to 10 mA

IL=0 to 8mA

2,3

0.008

0.010

0.012

0.015

%/m

Line Regulatio n

NOTE 2 LN reg VIN=13V to 33V

2,3 All 0.010

0.015 %/V

Load Current ILNOTE 1 1

2,3 All 10

8mA

Output Voltage

Noise enp-p 0.1Hz to 10Hz 4 All 150 µVp-

Output Voltage

Temperature

Coefficient TCVo NOTE 4 4,5,6 01

±8.5

±25 ppm/°

NOTE 1: Minimum l oad current guar anteed by load regulat ion test.

NOTE 2: Line and Load Regulation specifications include the effect of self-heating.

NOTE 3: LD Reg=∆IL/∆VOUTx100

NOTE 4: VMAX-VMIN (-55°C to +125°C)1x106

TCVO= ----------------- x ----------------------------------

10V +180°C

ORDERING INFORMATION:

Device Package Maxim Device SMD Number

01 G99 REF01AJ/883B 5962-8958103GC

01 J8 REF01AZ/883B 5962-8958103PA

01 L20 REF01ARC/883B 5962-89581032C

02 G99 REF01J/883B 5962-8958104GC

02 J8 REF01Z/883B 5962-8958104PA

02 L20 REF01RC/883B 5962-89581042C

---------------------------- Electrical Characteristics of REF01 & 01A/883B 19-0490 Rev. C

for /883B and SMD 5962-89581 Page 3 of 6

PIN CONFIGURATIONS:

8 Lead CERDIP 8 Lead CAN 20 Lead LCC

1NC NC NC

IN VIN NC

3NC NC NC

4 GND GND (case) NC

5 TRIM TRIM VIN

OUT VOUT NC

7NC NC NC

8NC NC NC

9NC

10 GND

11 NC

12 TRIM

13 NC

14 NC

15 VOUT

16 NC

17 NC

18 NC

19 NC

20 NC

---------------------------- Electrical Characteristics of REF01 & 01A/883B 19-0490 Rev. C

for /883B and SMD 5962-89581 Page 4 of 6

QUALITY ASSURAN CE

Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as

specified in Mil-Std-883.

Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:

1. Test Condition, A, B, C, or D.

2. TA = +125°C mini mum.

3. Interim and final electrical test requirements shall be specified in Table 2.

Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883,

including Groups A, B, C, and D inspection.

Group A inspection:

1. Tests as specified in Table 2.

2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.

Group C and D inspections:

a. End-point electrical parameters shall be specified in Table 1.

b. Steady-state life test, Method 1005 of Mil-Std-883:

1. Test condition A, B, C, D.

2. TA = +125°C, minimum.

3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.

TABLE 2. ELECTRICAL TEST REQUIR EMENTS

Mil-Std-883 Test Requirements Subgroups

per Method 5005, Table 1

Interim Electric Parameters

Method 5004 1

Final Electrical Parameters

Method 5005 1*, 2, 3, 4, 5, 6

Group A Test Requirements

Method 5005 1, 2, 3, 4, 5, 6

Group C and D End-Point Electrical Parameters

Method 5005 1

* PDA applies to Subgroup 1 only.

---------------------------- Electrical Characteristics of REF01 & 01A/883B 19-0490 Rev. C

for /883B and SMD 5962-89581 Page 5 of 6