SCOPE: PRECISION REFERENCE +10 VOLT ADJUSTABLE OUTPUT Device Type 01 02 Generic Number REF01A(x)/883B REF01(x)/883B Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Outline Letter MAXIM SMD Z P J G RC 2 Mil-Std-1835 GDIP1-T8 or CDIP2-T8 MACY1-X8 CQCC1-N20 Case Outline Package Code 8 LEAD CERDIP 8 LEAD CAN 20 Pin Ceramic LCC J8 G99 L20 Absolute Maximum Ratings Supply Voltage VDD to GND ................................................................................... 40V Output Short Circuit Duration (to GND or VIN) ............................................... Indefinite Lead Temperature (soldering, 10 seconds) ............................................................... +300C Storage Temperature .................................................................................. -65C to +150C Continuous Power Dissipation .............................................................................TA=+70C 8 lead CERDIP(derate 8.0mW/C above +70C) .................................................... 640mW 8 pin CAN (derate 6.67mW/C above +70C)......................................................... 533mW 20-Pin LCC (derate 9.09mW/C above +70C) ...................................................... 727mW Junction Temperature TJ ....................................................................................... +150C Thermal Resistance, Junction to Case, JC: Case Outline 8 lead CERDIP.................................................................. 55C/W Case Outline 8 lead CAN ....................................................................... 45C/W Case Outline 20-Pin LCC ....................................................................... 20C/W Thermal Resistance, Junction to Ambient, JA: Case Outline 8 lead CERDIP................................................................. 125C/W Case Outline 8 lead CAN ...................................................................... 150C/W Case Outline 20-Pin LCC ..................................................................... 110C/W Recommended Operating Conditions. VOUT @ 25C for device 01 ............................................................................ 5V 15mV VOUT @ 25C for device 02 ............................................................................ 5V 25mV Ambient Operating Range (TA) ........................................................... -55C to +125C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of REF01 & 01A/883B for /883B and SMD 5962-89581 19-0490 Page 2 of Rev. C 6 TABLE 1 ELECTRICAL TESTS TEST Symbol Quiescent Supply Current Output Adjustment Range Output Voltage IIN CONDITIONS -55 C TA +125C VDD=+15V, VIN=+15V Unless otherwise specified No load VTRIM RP=10k VO IL=0mA Output Voltage VO IL=0mA Short Circuit Current Sink Current ISC VO=0 Load Regulation NOTES 1, 2, 3 LD reg IS IL=0 to 10 mA IL=0 to 8mA Group A Subgroup 1 2,3 1 Device type Limits Min Limits Max All All -3.0 1.4 2.0 +3.0 01 10.03 10.04 10.05 10.095 +60 1 2,3 1 2,3 1 All 9.97 9.95 9.95 9.905 +15 1 All -0.3 1 01 02 0.008 0.010 2,3 01 02 0.012 0.015 0.010 02 1 Line Regulation NOTE 2 Load Current Output Voltage Noise Output Voltage Temperature Coefficient NOTE 1: NOTE 2: NOTE 3: NOTE 4: VIN=13V to 33V NOTE 1 enp-p 0.1Hz to 10Hz TCVo NOTE 4 2,3 1 2,3 4 mA % V V mA mA All LN reg IL Units %/m A %/V 0.015 All 10 8 mA All 150 01 8.5 02 25 4,5,6 Vpp ppm/ C Minimum load current guaranteed by load regulation test. Line and Load Regulation specifications include the effect of self-heating. LD Reg=IL/VOUTx100 VMAX-VMIN (-55C to +125C)1x106 TCVO= ----------------- x ---------------------------------10V +180C ORDERING INFORMATION: Device Package Maxim Device 01 G99 REF01AJ/883B 01 J8 REF01AZ/883B 01 L20 REF01ARC/883B 02 G99 REF01J/883B 02 J8 REF01Z/883B 02 L20 REF01RC/883B ---------------------------- SMD Number 5962-8958103GC 5962-8958103PA 5962-89581032C 5962-8958104GC 5962-8958104PA 5962-89581042C Electrical Characteristics of REF01 & 01A/883B for /883B and SMD 5962-89581 19-0490 Page 3 of Rev. C 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PIN CONFIGURATIONS: 8 Lead CERDIP 8 Lead CAN 20 Lead LCC NC NC NC VIN VIN NC NC NC NC GND GND (case) NC TRIM TRIM VIN VOUT VOUT NC NC NC NC NC NC NC NC GND NC TRIM NC NC VOUT NC NC NC NC NC ---------------------------- Electrical Characteristics of REF01 & 01A/883B for /883B and SMD 5962-89581 19-0490 Page 4 of Rev. C 6 QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-Std-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * Subgroups per Method 5005, Table 1 1 1*, 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6 1 PDA applies to Subgroup 1 only. ---------------------------- Electrical Characteristics of REF01 & 01A/883B for /883B and SMD 5962-89581 19-0490 Page 5 of Rev. C 6