Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
LMx93-N, LM2903-N Low-Power, Low-Offset Voltage, Dual Comparators
1 Features 3 Description
The LM193-N series consists of two independent
1• Wide Supply precision voltage comparators with an offset voltage
– Voltage Range: 2.0 V to 36 V specification as low as 2.0 mV max for two
– Single or Dual Supplies: ±1.0 V to ±18 V comparators which were designed specifically to
operate from a single power supply over a wide range
• Very Low Supply Current Drain (0.4 mA) — of voltages. Operation from split power supplies is
Independent of Supply Voltage also possible and the low power supply current drain
• Low Input Biasing Current: 25 nA is independent of the magnitude of the power supply
• Low Input Offset Current: ±5 nA voltage. These comparators also have a unique
characteristic in that the input common-mode voltage
• Maximum Offset voltage: ±3 mV range includes ground, even though operated from a
• Input Common-Mode Voltage Range Includes single power supply voltage.
Ground Application areas include limit comparators, simple
• Differential Input Voltage Range Equal to the analog to digital converters; pulse, squarewave and
Power Supply Voltage time delay generators; wide range VCO; MOS clock
• Low Output Saturation Voltage: 250 mV at 4 mA timers; multivibrators and high voltage digital logic
• Output Voltage Compatible with TTL, DTL, ECL, gates. The LM193-N series was designed to directly
interface with TTL and CMOS. When operated from
MOS and CMOS logic systems both plus and minus power supplies, the LM19-N
• Available in the 8-Bump (12 mil) DSBGA Package series will directly interface with MOS logic where
• See AN-1112 (SNVA009) for DSBGA their low power drain is a distinct advantage over
Considerations standard comparators.
• Advantages The LM393 and LM2903 parts are available in TI’s
– High Precision Comparators innovative thin DSBGA package with 8 (12 mil) large
bumps.
– Reduced VOS Drift Over Temperature
– Eliminates Need for Dual Supplies Device Information(1)
– Allows Sensing Near Ground PART NUMBER PACKAGE BODY SIZE (NOM)
– Compatible with All Forms of Logic LM193-N TO-99 (8) 9.08 mm x 9.08 mm
– Power Drain Suitable for Battery Operation LM293-N
LM393-N SOIC (8) 4.90 mm x 3.91 mm
2 Applications LM2903-N
• Battery powered applications (1) For all available packages, see the orderable addendum at
the end of the datasheet.
• Industrial applications
4 Simplified Schematic
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
www.ti.com
Table of Contents
1 Features.................................................................. 18 Detailed Description............................................ 10
8.1 Overview................................................................. 10
2 Applications ........................................................... 18.2 Functional Block Diagram....................................... 10
3 Description............................................................. 18.3 Feature Description................................................. 10
4 Simplified Schematic............................................. 18.4 Device Functional Modes........................................ 10
5 Revision History..................................................... 29 Application and Implementation ........................ 11
6 Pin Configuration and Functions......................... 39.1 Application Information............................................ 11
7 Specifications......................................................... 49.2 Typical Applications ................................................ 11
7.1 Absolute Maximum Ratings ..................................... 410 Power Supply Recommendations ..................... 18
7.2 ESD Ratings ............................................................ 411 Layout................................................................... 18
7.3 Recommended Operating Conditions....................... 411.1 Layout Guidelines ................................................. 18
7.4 Thermal Information.................................................. 511.2 Layout Example .................................................... 18
7.5 Electrical Characteristics: LM193A V+= 5 V, TA=
25°C........................................................................... 512 Device and Documentation Support................. 19
7.6 Electrical Characteristics: LM193A (V+ = 5 V) ......... 512.1 Related Links ........................................................ 19
7.7 Electrical Characteristics: LMx93 and LM2903 V+= 5 12.2 Trademarks........................................................... 19
V, TA= 25°C .............................................................. 612.3 Electrostatic Discharge Caution............................ 19
7.8 Electrical Characteristics: LMx93 and LM2903 (V+ = 12.4 Glossary................................................................ 19
5 V)(1)......................................................................... 713 Mechanical, Packaging, and Orderable
7.9 Typical Characteristics: LMx93 and LM193A............ 8Information ........................................................... 19
7.10 Typical Characteristics: LM2903 ............................ 9
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (March 2013) to Revision F Page
• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes,Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision D (March 2013) to Revision E Page
• Changed layout of National Data Sheet to TI format ............................................................................................................ 1
2Submit Documentation Feedback Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
www.ti.com
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
6 Pin Configuration and Functions
8-Pin TO-99 8-Pin CDIP, PDIP, SOIC
LMC Package P and D Package
Top View Top View
8-Pin DSBGA
YZR Package
Top View
Pin Functions
PIN
NO. I/O DESCRIPTION
NAME PDIP/SOIC/ DSBGA
TO-99
OUTA 1 A1 O Output, Channel A
-INA 2 B1 I Inverting Input, Channel A
+INA 3 C1 I Noninverting Input, Channel A
GND 4 C2 P Ground
+INB 5 C3 I Noninverting Input, Channel B
-INB 6 B3 I Inverting Input, Channel B
OUTB 7 A3 O Output, Channel B
V+ 8 A2 P Positive power supply
Copyright © 1999–2014, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)(3)
MIN MAX UNIT
Differential Input Voltage (4) 36 V
Input Voltage −0.3 36 V
Input Current (VIN<−0.3 V) (5) 50 mA
Power PDIP 780 mW
Dissipation (6) TO-99 660 mW
SOIC 510 mW
DSBGA 568 mW
Output Short-Circuit to Ground (7) Continu
ous
Lead Temperature (Soldering, 10 seconds) 260 °C
Soldering PDIP Package Soldering (10 seconds) 260 °C
Information SOIC Package Vapor Phase (60 seconds) 215 °C
Infrared (15 seconds) 220 °C
Storage temperature, Tstg -65 150 °C
(1) Absolute Maximum Ratings indicate limits beyond which damage may occur. Recommended Operating Conditions indicate conditions
for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and test
conditions, see the Electrical Characteristics.
(2) Refer to RETS193AX for LM193AH military specifications and to RETS193X for LM193H military specifications.
(3) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(4) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than −0.3V (or 0.3V below the
magnitude of the negative power supply, if used).
(5) This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of
the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is
also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the comparators to go
to the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive
and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3V.
(6) For operating at high temperatures, the LM393 and LM2903 must be derated based on a 125°C maximum junction temperature and a
thermal resistance of 170°C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The
LM193/LM193A/LM293 must be derated based on a 150°C maximum junction temperature. The low bias dissipation and the “ON-OFF”
characteristic of the outputs keeps the chip dissipation very small (PD≤100 mW), provided the output transistors are allowed to saturate.
(7) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 20 mA independent of the magnitude of V+.
7.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±1300 V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT
Supply Voltage (V+) - Single Supply 2.0 36 V
Supply Voltage (V+) - Dual Supply ±1.0 ±18 V
Operating Input Voltage on (VIN pin) 0 (V+) -1.5V V
Operating junction temperature, TJ: LM193/LM193A -55 125 °C
Operating junction temperature, TJ: LM2903 -40 85 °C
Operating junction temperature, TJ: LM293 -25 85 °C
Operating junction temperature, TJ: LM393 0 70 °C
4Submit Documentation Feedback Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
www.ti.com
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
7.4 Thermal Information LMx93
THERMAL METRIC(1) TO-99 UNIT
8 PINS
RθJA Junction-to-ambient thermal resistance 170 °C/W
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
7.5 Electrical Characteristics: LM193A V+= 5 V, TA= 25°C
Unless otherwise stated. LM193A
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX
Input Offset Voltage See (1). 1.0 2.0 mV
Input Bias Current IIN(+) or IIN(−) with Output In Linear Range, VCM = 0 V (2) 25 100 nA
Input Offset Current IIN(+)−IIN(−) VCM = 0 V 3.0 25 nA
Input Common Mode Voltage Range V+ = 30 V (3) 0 V+−1.5 V
Supply Current RL=∞V+=5 V 0.4 1 mA
V+=36 V 1 2.5 mA
Voltage Gain RL≥15 kΩ, V+=15 V 50 200 V/mV
VO= 1 V to 11 V
Large Signal Response Time VIN=TTL Logic Swing, VREF=1.4 V 300 ns
VRL=5V, RL=5.1 kΩ
Response Time VRL=5V, RL=5.1 kΩ(4) 1.3 μs
Output Sink Current VIN(−)=1V, VIN(+)=0, VO≈1.5 V 6.0 16 mA
Saturation Voltage VIN(−)=1V, VIN(+)=0, ISINK≤4 mA 250 400 mV
Output Leakage Current VIN(−)=0, VIN(+)=1V, VO=5 V 0.1 nA
(1) At output switch point, VO≃1.4V, RS= 0 Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V), at 25°C.
(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(3) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+−1.5 V at 25°C, but either or both inputs can go to 36 V without damage, independent of the
magnitude of V+.
(4) The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see
LMx93 and LM193A Typical Characteristics .
7.6 Electrical Characteristics: LM193A (V+ = 5 V)(1)
LM193A
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX
Input Offset Voltage See (2) 4.0 mV
Input Offset Current IIN(+)−IIN(−), VCM=0 V 100 nA
Input Bias Current IIN(+) or IIN(−) with Output in Linear Range, VCM=0 V (3) 300 nA
Input Common Mode Voltage Range V+=30 V (4) 0 V+−2.0 V
Saturation Voltage VIN(−)=1V, VIN(+)=0, ISINK≤4 mA 700 mV
Output Leakage Current VIN(−)=0, VIN(+)=1V, VO=30 V 1.0 μA
Differential Input Voltage Keep All VIN's≥0 V (or V−, if Used), (5) 36 V
(1) These specifications are limited to −55°C≤TA≤+125°C, for the LM193/LM193A. With the LM293 all temperature specifications are limited
to −25°C≤TA≤+85°C and the LM393 temperature specifications are limited to 0°C≤TA≤+70°C. The LM2903 is limited to
−40°C≤TA≤+85°C.
(2) At output switch point, VO≃1.4V, RS= 0 Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V), at 25°C.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(4) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+−1.5 V at 25°C, but either or both inputs can go to 36 V without damage, independent of the
magnitude of V+.
(5) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than −0.3V (or 0.3V below the
magnitude of the negative power supply, if used).
Copyright © 1999–2014, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
www.ti.com
7.7 Electrical Characteristics: LMx93 and LM2903 V+= 5 V, TA= 25°C
Unless otherwise stated. LM193-N LM293-N, LM393- LM2903-N
N
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX MIN TYP MAX
Input Offset Voltage See (1) 1.0 5.0 1.0 5.0 2.0 7.0 mV
Input Bias Current IIN(+) or IIN(−) with Output In 25 100 25 250 25 250 nA
Linear Range, VCM = 0 V (2)
Input Offset Current IIN(+)−IIN(−) VCM = 0 V 3.0 25 5.0 50 5.0 50 nA
Input Common Mode V+ = 30 V (3) 0 V+−1. 0 V+−1 0 V+−1 V
Voltage Range 5 .5 .5
Supply Current RL=∞V+=5 V 0.4 1 0.4 1 0.4 1.0 mA
V+=36 V 1 2.5 1 2.5 1 2.5 mA
Voltage Gain RL≥15 kΩ, V+=15 V 50 200 50 200 25 100 V/mV
VO= 1 V to 11 V
Large Signal Response VIN=TTL Logic Swing, VREF=1.4 V 300 300 300 ns
Time VRL=5 V, RL=5.1 kΩ
Response Time VRL=5 V, RL=5.1 kΩ(4) 1.3 1.3 1.5 μs
Output Sink Current VIN(−)=1 V, VIN(+)=0, VO≤1.5 V 6.0 16 6.0 16 6.0 16 mA
Saturation Voltage VIN(−)=1 V, VIN(+)=0, ISINK≤4 mA 250 400 250 400 250 400 mV
Output Leakage Current VIN(−)=0, VIN(+)=1V, VO=5 V 0.1 0.1 0.1 nA
(1) At output switch point, VO≃1.4V, RS= 0 Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V), at 25°C.
(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(3) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+−1.5 V at 25°C, but either or both inputs can go to 36 V without damage, independent of the
magnitude of V+.
(4) The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see
LMx93 and LM193A Typical Characteristics .
6Submit Documentation Feedback Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
www.ti.com
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
7.8 Electrical Characteristics: LMx93 and LM2903 (V+ = 5 V)(1)
LM193-N LM293-N, LM393- LM290-N
N
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX MIN TYP MAX
Input Offset Voltage See (2) 9 9 9 15 mV
Input Offset Current IIN(+)−IIN(−), VCM=0 V 100 150 50 200 nA
Input Bias Current IIN(+) or IIN(−) with Output in 300 400 200 500 nA
Linear Range, VCM=0 V
(3)
Input Common Mode V+=30V (4) 0 V+−2 0 V+−2 0 V+−2. V
Voltage Range .0 .0 0
Saturation Voltage VIN(−)=1V, VIN(+)=0, 700 700 400 700 mV
ISINK≤4 mA
Output Leakage Current VIN(−)=0, VIN(+)=1V, VO=30 V 1.0 1.0 1.0 μA
Differential Input Voltage Keep All VIN's≥0 V (or V−, if 36 36 36 V
Used), (5)
(1) These specifications are limited to −55°C≤TA≤+125°C, for the LM193/LM193A. With the LM293 all temperature specifications are limited
to −25°C≤TA≤+85°C and the LM393 temperature specifications are limited to 0°C≤TA≤+70°C. The LM2903 is limited to
−40°C≤TA≤+85°C.
(2) At output switch point, VO≃1.4V, RS= 0 Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V), at 25°C.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the reference or input lines.
(4) The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end
of the common-mode voltage range is V+−1.5 V at 25°C, but either or both inputs can go to 36 V without damage, independent of the
magnitude of V+.
(5) Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode
range, the comparator will provide a proper output state. The low input voltage state must not be less than −0.3V (or 0.3V below the
magnitude of the negative power supply, if used).
Copyright © 1999–2014, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
www.ti.com
7.9 Typical Characteristics: LMx93 and LM193A
Figure 1. Supply Current Figure 2. Input Current
Figure 4. Response Time for Various Input
Figure 3. Output Saturation Voltage Overdrives—Negative Transition
Figure 5. Response Time for Various Input Overdrives—Positive Transition
8Submit Documentation Feedback Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
www.ti.com
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
7.10 Typical Characteristics: LM2903
Figure 7. Input Current
Figure 6. Supply Current
Figure 9. Response Time for Various Input
Overdrives—Negative Transition
Figure 8. Output Saturation Voltage
Figure 10. Response Time for Various Input Overdrives—Positive Transition
Copyright © 1999–2014, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
www.ti.com
8 Detailed Description
8.1 Overview
The LM139 provides two independently functioning, high-precision, low VOS drift, low input bias current
comparators in a single package. The low power consumption of 0.4mA at 5V and the 2.0V supply operation
makes the LM139 suitable for battery powered applications.
8.2 Functional Block Diagram
Figure 11. Basic Comparator
8.3 Feature Description
The input bias current of 25 nA enables the LM193 to use even very high impedance nodes as inputs. The
differential voltage input range equals the supply voltage range.
The LM193 can be operated with a single supply, where V+ can be from 2.0 V to 36 V, or in a dual supply
voltage configuration, where GND pin is used as a V– supply. The supply current draws only 0.4 mA for both
comparators.
The output of each comparator in the LM193 is the open collector of a grounded-emitter NPN output transistor
which can typically draw up to 16mA.
8.4 Device Functional Modes
A basic comparator circuit is used for converting analog signals to a digital output. The output is HIGH when the
voltage on the non-inverting (+IN) input is greater than the inverting (-IN) input. The output is LOW when the
voltage on the non-inverting (+IN) input is less than the inverting (-IN) input. The inverting input (-IN) is also
commonly referred to as the "reference" or "VREF" input. All pins of any unused comparators should be tied to
the negative supply.
10 Submit Documentation Feedback Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
www.ti.com
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LM193 series are high gain, wide bandwidth devices which, like most comparators, can easily oscillate if the
output lead is inadvertently allowed to capacitively couple to the inputs via stray capacitance. This shows up only
during the output voltage transition intervals as the comparator change states. Power supply bypassing is not
required to solve this problem. Standard PC board layout is helpful as it reduces stray input-output coupling.
Reducing the input resistors to < 10 kΩreduces the feedback signal levels and finally, adding even a small
amount (1.0 to 10 mV) of positive feedback (hysteresis) causes such a rapid transition that oscillations due to
stray feedback are not possible. Simply socketing the IC and attaching resistors to the pins will cause input-
output oscillations during the small transition intervals unless hysteresis is used. If the input signal is a pulse
waveform, with relatively fast rise and fall times, hysteresis is not required.
All input pins of any unused comparators should be tied to the negative supply.
The bias network of the LM193 series establishes a drain current which is independent of the magnitude of the
power supply voltage over the range of from 2.0 VDC to 30 VDC.
The differential input voltage may be larger than V+without damaging the deviceTypical Applications . Protection
should be provided to prevent the input voltages from going negative more than −0.3 VDC (at 25°C). An input
clamp diode can be used as shown in Typical Applications .
The output of the LM193 series is the uncommitted collector of a grounded-emitter NPN output transistor. Many
collectors can be tied together to provide an output OR'ing function. An output pullup resistor can be connected
to any available power supply voltage within the permitted supply voltage range and there is no restriction on this
voltage due to the magnitude of the voltage which is applied to the V+terminal of the LM193 package. The
output can also be used as a simple SPST switch to ground (when a pullup resistor is not used). The amount of
current which the output device can sink is limited by the drive available (which is independent of V+) and the β
of this device. When the maximum current limit is reached (approximately 16mA), the output transistor will come
out of saturation and the output voltage will rise very rapidly. The output saturation voltage is limited by the
approximately 60ΩrSAT of the output transistor. The low offset voltage of the output transistor (1.0mV) allows the
output to clamp essentially to ground level for small load currents.
9.2 Typical Applications
9.2.1 Basic Comparator
Figure 12. Basic Comparator
9.2.1.1 Design Requirements
The basic usage of a comparator is to indicate when a specific analog signal has exceeded some predefined
threshold. In this application, the negative input (IN–) is tied to a reference voltage, and the positive input (IN+) is
connected to the input signal. The output is pulled up with a resistor to the logic supply voltage, V+ with a pullup
resistor.
For an example application, the supply voltage is 5V. The input signal varies between 1 V and 3 V, and we want
to know when the input exceeds 2.5 V±1%. The supply current draw should not exceed 1 mA.
Copyright © 1999–2014, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
www.ti.com
Typical Applications (continued)
9.2.1.2 Detailed Design Procedure
First, we determine the biasing for the 2.5-V reference. With the 5-V supply voltage, we would use a voltage
divider consisting of one resistor from the supply to IN- and an second resistor from IN–. The 25 nA of input
current bias should be < 1% of the bias current for Vref. With a 100-kΩresistor from IN– to V+ and an additional
100-KΩresistor from IN– to ground, there would be 25 µA of current through the two resistors. The 3-kΩpullup
shown will need 5 V/3 kΩ → 1.67 mA, which exceeds our current budget.
With the 400-µA supply current and 25 µA of VREF bias current, there is 575 µA remaining for output pullup
resistor; with 5-V supply, we need a pullup larger than 8.7 kΩ. A 10-kΩpullup is a value that is commonly
available and can be used here.
9.2.1.3 Application Curve
Figure 13. Basic Comparator Response
12 Submit Documentation Feedback Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
www.ti.com
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
Typical Applications (continued)
9.2.2 System Examples
9.2.2.1 Split-Supply Application
(V+=-15 VDC and V-=-15 VDC)
Figure 14. MOS Clock Driver
9.2.2.2 V+ = 5.0 VDC Application Circuits
Figure 15. Driving CMOS Figure 16. Driving TTL
* For large ratios of R1/R2,
D1 can be omitted.
Figure 17. Squarewave Oscillator Figure 18. Pulse Generator
Copyright © 1999–2014, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
www.ti.com
Typical Applications (continued)
V* = +30 VDC
+250 mVDC ≤VC≤+50 VDC
700Hz ≤fo≤100kHz
Figure 19. Crystal Controlled Oscillator Figure 20. Two-Decade High Frequency VCO
Figure 21. Basic Comparator Figure 22. Non-Inverting Comparator With
Hysteresis
Figure 23. Inverting Comparator With Hysteresis Figure 24. Output Strobing
14 Submit Documentation Feedback Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
www.ti.com
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
Typical Applications (continued)
Figure 25. And Gate Figure 26. Or Gate
Figure 27. Large Fan-In and Gate Figure 28. Limit Comparator
Figure 29. Comparing Input Voltages of Opposite Figure 30. Oring the Outputs
Polarity
Copyright © 1999–2014, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
www.ti.com
Typical Applications (continued)
Figure 31. Zero Crossing Detector (Single Power Figure 32. One-Shot Multivibrator
Supply)
Figure 33. Bi-Stable Multivibrator Figure 34. One-Shot Multivibrator With Input Lock
Out
Figure 35. Zero Crossing Detector Figure 36. Comparator With a Negative Reference
16 Submit Documentation Feedback Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
www.ti.com
10 Power Supply Recommendations
Even in low frequency applications, the LM139-N can have internal transients which are extremely quick. For this
reason, bypassing the power supply with 1.0μF to ground will provide improved performance; the supply bypass
capacitor should be placed as close as possible to the supply pin and have a solid connection to ground. The
bypass capacitor should have a low ESR and also a SRF greater than 50MHz.
11 Layout
11.1 Layout Guidelines
Try to minimize parasitic impedances on the inputs to avoid oscillation. Any positive feedback used as hysteresis
should place the feedback components as close as possible to the input pins. Care should be taken to ensure
that the output pins do not couple to the inputs. This can occur through capacitive coupling if the traces are too
close and lead to oscillations on the output. The optimum placement for the bypass capacitor is closest to the V+
and ground pins. Take care to minimize the loop area formed by the bypass capacitor connection between V+
and ground. The ground pin should be connected to the PCB ground plane at the pin of the device. The
feedback components should be placed as close to the device as possible minimizing strays.
11.2 Layout Example
Figure 38. Layout Example
18 Submit Documentation Feedback Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
LM193-N
,
LM2903-N
,
LM293-N
,
LM393-N
www.ti.com
SNOSBJ6F –OCTOBER 1999–REVISED DECEMBER 2014
12 Device and Documentation Support
12.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY
LM193-N Click here Click here Click here Click here Click here
LM2903-N Click here Click here Click here Click here Click here
LM293-N Click here Click here Click here Click here Click here
LM393-N Click here Click here Click here Click here Click here
12.2 Trademarks
All trademarks are the property of their respective owners.
12.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.4 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 1999–2014, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM193-N LM2903-N LM293-N LM393-N
PACKAGE OPTION ADDENDUM
www.ti.com 21-Nov-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM193AH ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -55 to 125 ( LM193AH, LM193AH
)
LM193AH/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 125 ( LM193AH, LM193AH
)
LM193H ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -55 to 125 ( LM193H, LM193H)
LM193H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 125 ( LM193H, LM193H)
LM2903ITL/NOPB ACTIVE DSBGA YZR 8 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 C
03
LM2903ITLX/NOPB ACTIVE DSBGA YZR 8 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 C
03
LM2903M ACTIVE SOIC D 8 95 TBD Call TI Call TI -40 to 85 LM
2903M
LM2903M/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM
2903M
LM2903MX LIFEBUY SOIC D 8 2500 TBD Call TI Call TI -40 to 85 LM
2903M
LM2903MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM
2903M
LM2903N/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 LM
2903N
LM293H ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -25 to 85 ( LM293H, LM293H)
LM293H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM -25 to 85 ( LM293H, LM293H)
LM393M NRND SOIC D 8 95 TBD Call TI Call TI 0 to 70 LM
393M
LM393M/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM
393M
LM393MX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 70 LM
393M
LM393MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM
393M
PACKAGE OPTION ADDENDUM
www.ti.com 21-Nov-2017
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM393N/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 70 LM
393N
LM393TL/NOPB ACTIVE DSBGA YZR 8 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 70 C
02
LM393TLX/NOPB ACTIVE DSBGA YZR 8 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 70 C
02
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 21-Nov-2017
Addendum-Page 3
OTHER QUALIFIED VERSIONS OF LM2903-N, LM293-N :
•Automotive: LM2903-Q1
•Enhanced Product: LM293-EP
NOTE: Qualified Version Definitions:
•Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•Enhanced Product - Supports Defense, Aerospace and Medical Applications
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM2903ITL/NOPB DSBGA YZR 8 250 178.0 8.4 1.7 1.7 0.76 4.0 8.0 Q1
LM2903ITLX/NOPB DSBGA YZR 8 3000 178.0 8.4 1.7 1.7 0.76 4.0 8.0 Q1
LM2903MX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM2903MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM393MX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM393MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM393TL/NOPB DSBGA YZR 8 250 178.0 8.4 1.7 1.7 0.76 4.0 8.0 Q1
LM393TLX/NOPB DSBGA YZR 8 3000 178.0 8.4 1.7 1.7 0.76 4.0 8.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 9-Oct-2014
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2903ITL/NOPB DSBGA YZR 8 250 210.0 185.0 35.0
LM2903ITLX/NOPB DSBGA YZR 8 3000 210.0 185.0 35.0
LM2903MX SOIC D 8 2500 367.0 367.0 35.0
LM2903MX/NOPB SOIC D 8 2500 367.0 367.0 35.0
LM393MX SOIC D 8 2500 367.0 367.0 35.0
LM393MX/NOPB SOIC D 8 2500 367.0 367.0 35.0
LM393TL/NOPB DSBGA YZR 8 250 210.0 185.0 35.0
LM393TLX/NOPB DSBGA YZR 8 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 9-Oct-2014
Pack Materials-Page 2
MECHANICAL DATA
YZR0008xxx
www.ti.com
TLA08XXX (Rev C)
0.600±0.075 D
E
A
. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
4215045/A 12/12
D: Max =
E: Max =
1.54 mm, Min =
1.54 mm, Min =
1.479 mm
1.479 mm
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
