Vicon Lrem Numeen AlclO9 Rev 0 ! te Agilent Technologies Low Input Current, High Gain Optocouplers Technical Data Features * High Current Transfer Ratio 2000% Typical (4500% Typical for HCNW139/138) * Low Input Current Requirements 0.5 mA * TTL Compatible Output - 0.1 V Vor, Typical * Performance Guaranteed over Temperature 0C to 70C Base Access Allows Gain Bandwidth Adjustment * High Output Current 60 mA Safety Approval UL Recognized - 2500 V rms for 1 Minute and 5000 V rms* for 1 Minute per UL 1577 CSA Approved VDE 0884 Approved with ViorM = 1414 V peak for HCNW139 and HCNW138 * Available in 8-Pin DIP or SOIC-8 Footprint or Widebody Package *MIL-STD-1772 Version Available (HCPL-5700/1) Applications * Ground Isolate Most Logic Families TTL/TTL, CMOS/ TTL, CMOS/CMOS, LSTTL/ TTL, CMOS/LSTTL * Low Input Current Line Receiver * High Voltage Insulation (HCNW139/138) * EIA RS-232C Line Receiver * Telephone Ring Detector * 117 V ac Line Voltage Status Indicator - Low Input Power Dissipation * Low Power Systems Ground Isolation Functional Diagram NC [1] a Vec ANODE ae 7] Vp CATHODE [3] 6] Vo ne [4] Us] GND 6N139 6N138 HCPL-0701 HCPL-0700 HCNW139 HCNW138 Description These high gain series couplers use a Light Emitting Diode and an integrated high gain photodetec- tor to provide extremely high current transfer ratio between input and output. Separate pins for the photodiode and output stage result in TTL compatible saturation voltages and high speed operation. Where desired the Vec and Vp terminals may be tied together to achieve conven- tional photodarlington operation. A base access terminal allows a gain bandwidth adjustment to be made. TRUTH TABLE LED Vo ON Low OFF_| HIGH ORIGINAL ONLY WHEN STAMPED IN RED *5000 V rms/1 minute rating is for HCNW139/138 and Option 020 (6N139/138) products only. AQ.1 uF bypass capacitor connected between pins 8 and 5 is recommended. | CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.Vicon Lrem Numer ALIO9 The 6N139, HCPL-0701, and CNW139 are for use in CMOS, LSTTL or other low power appli- cations. A 400% minimum current transfer ratio is guaranteed over 0 to 70C operating range for only 0.5 mA of LED current. The 6N138, HCPL-0700, and HCNW138 are designed for use mainly in TTL applications. Current Transfer Ratio (CTR) is 300% minimum over 0 to 70C for an LED current of 1.6 mA Selection Guide (1 TTL Unit load ). A 300% minimum CTR enables operation with 1 TTL Load using a 2.2 kQ pull-up resistor. Selection for lower input current down to 250 pA is available upon request. The HCPL-0701 and HCPL-0700 are surface mount devices packaged in an industry standard SOIC-8 footprint. Rey FQ 2 The SOIC-8 does not require through holes in a PCB. This package occupies approximately one-third the footprint area of the standard dual-in-line package. The lead profile is designed to be compatible with standard surface mount processes. The HCNW139 and HCNW138 are packaged in a widebody encapsulation that provides creep- age and clearance dimensions suitable for safety approval by regulatory agencies worldwide. Widebody 8-Pin DIP Package Hermetic (300 Mil) Small Outline SO-8 | (400 mil Single and Dual Single Dual Minimum Absolute Dual Single Channel | Channel | Channel Single Input ON Maxi- Channel Channel Package | Package | Package | Channel Current | Minimum mum Packages Package HCPL- HCPL- HCPL- Package (Up) CTR Voc HCPL- 6N139 273101 0701 0731 HCNW139 0.5 mA 400% 18 V 6N138 27300! 0700 0730 HCNW138 1.6mA 300% 7V HCPL-4701)1 | 47310) O70A!! 073A!) 40 wA 800% 18V 0.5 mA 300% 20 V 570101 570011 57310) 573001 Note: 1. Technical data are on separate Agilent publications. ORIGINAL ONLY WHEN STAMPED IN REDVicon Trem Numer alolO4 Rev #0 Ordering Information Specify Part Number followed by Option Number (if desired). Example: 6N139#XXX 020 = 5000 V rms/1 Minute UL Rating Option* 300 = Gull Wing Surface Mount Option; 500 = Tape and Reel Packaging Option Option data sheets available. Contact your Agilent sales representative or authorized distributor for information, *For 6N139 and 6N138 only. Gull wing surface mount option applies to through hole parts only. Schematic Vee 98 | loc 2 JFL | ANODE 1 * dy ZN Ve Ar I CATHODE | I l I I ORIGINAL ONLY WHEN STAMPED IN REDVico Lrem Numaern alolOF Rev #0 _ Package Outline Drawings 8-Pin DIP Package (6N139/6N138)** __ 9.654 0.25 _ 7.62 0.25 _, (0.380 + 0.010) (0.300 + 0.016) "| TYPE NUMBER___ | [5 Cr Ce] sl 6.35 + 0.25 (0.250 + 0.010) |- OPTION CODE* ae Roo ~~ [- DATE cove YYWW AU O SY [U L2} L3 | MI RECOGNITION Laze (0.070) MAX. 1.19 (0.047) MAX. + 0.076 0.254 | 9954 OE (0.010" pees) 4.70 (0.185) MAX. * 0.002) Tost (0.020) MIN. 2.92 (0.115) MIN. 1.08040.320 | 4 ||L 0.65 (0.025) MAX. 0.043 + 0.013 ( ) 2.54 + 0.25 DIMENSIONS IN MILLIMETERS AND (INCHES). (0.100 0.010) *MARKING CODE LETTER FOR OPTION NUMBERS L" = OPTION 020 OPTION NUMBERS 300 AND 500 NOT MARKED. * JEDEC Registered Data. 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N139/6N138) 9.65 40.25 ; 1.046 (0.040) [~*~ (0.380 + 0.010) "| 4194 (0.047) ce al oom e 6.3500.25 | | _ _ J (0.250 0,010) | 9.398 (0.370) O | 9.906 (0.390) yy i By g ooo ot ! - WP 1 | |. 0.381 (0.015) 1,194 (0.047) 0.635 (0.025) 1.778 (0.070) lug _9.65 0.25 (0.380 + 0.010) ORIGINAL _ 7.62 40.25 _ r (0.300 0.010) + 0.076 ONLY WHEN STAMPED 0.254 | 9.054 IN RED ld (ooro" 00 ts . lL 0.635 + 0.25 | t (0.025 + 0.010) ; 0.635 + 0.130 ~t 12 NOM. (0.025 + 0.005) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES).Vico rem Numpen AlolO4 Small Outline SO-8 Package (HCPL-0701/HCPL-0700) Rev *Q 1 oo, __... Ce 5.994 + 0.203 ; (0.236 + 0.008) XxX J 3.937 + 0.127 yww ~_| TYPE NUMBER (0.155 + 0.005) ~~ | (LAST 3 DIGITS) DATE CODE pinone fT PF A Ho 0.406 + 0.076>| + _. LL 1.270 ps (0.016 + 0.003) (0.050) _* 5,080 + 0.127 TP oy 0.432 (0.200 + 0.005) P Si X 0.017) TF, H | 3.175 4 0.127 o-7 (0.125 + 0.005) Fa 524 . 0.228 + 0.025 4 (0.060) , _ | _{ (0.009 + 0.001) yA ay + _ 0.203 + 0.102 (0.008 + 0.004) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 0.305 5.207 + 0.254 (0.205 + 0.040) (0.012) "N- DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. 8-Pin Widebody DIP Package (HCNW139/HCNW138) 14.15 0.15 ~ 11.00 wax. (0.442 + 0.006 (0.433) nat e900 0.15 _ (0.354 + 0.008) |_- TYPE NUMBER A HCNWXXXX a |_- DATE CODE YYWW 1 or Ya a | }~ 10.16 (0.400) > 455 | TYP. ; ia, >| et 7 TYP. + 0.076 MAX. Tit 0.254 | 9 9954 i (0.010 9.902) 5.40 (0.201)AX- + 40 0.122 ORIGINAL 3.90 (0.154) 0.51 (0.021) MIN. ONLY WHEN STAMPED IN RED 2.54 (0.100) TYP, 1.784045 J 0.40 (0.016) (0.070 + 0.006) 0.56 (0.022) DIMENSIONS IN MILLIMETERS (INCHES).Vico Lrem Numeen AlolO4 Rev #0 8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW139/HCNW138) < 11.1540.15 {0.442 + 0.006) PAD LOCATION (FOR REFERENCE ONLY) he | oooo- 6.15 (0.242) YP. 9.002015 | (0.35440.00e) : | 12,300.30 | O Slo ' (0.484 + 0.012) | 1 ; Tata aT Sosa tf >| ~ t 43 0.9 (0.051) (0.035) _ 1.55 12.30 4 0.30 ~ (0.064 (0.484 + 0.012) AX. M _ 11.00 MAX, (0.433) 4.00 (04 ga) MAX. JOO | 1.784015 ,| ja | f (0.070 + 6.006) | | _ _ 0.75 0.25 + 0.076 * (6.4100) (0.030 + 0.010) 0.254 o o054 BSC + 0.003) (0.010. 9.002) DIMENSIONS IN MILLIMETERS (INCHES). 7 NOM. LEAD COPLANARITY = 0.10 mm (0.004 INCHES). Solder Reflow Temperature Profile (HCPL-07XX and Gull Wing Surface Mount Option 300 Parts) 260 240 220 200 180 160 140 120 f 100 80 60 40 20 [- 0 TEMPERATURE - C T = 100C, 1.5C/SEC 0 1 2 3 4 5 6 7 8 9 10 11 12 TIME MINUTES Note: Use of nonchlorine activated fluxes is highly recommended. 0 nL WEN Mit PED N REDVicor Lrem Numeen AliO4 Rev #0 Regulatory Information The 6N139/138, HCNW139/138, and HCPL-0701/0700 have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File 55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. VDE Approved according to VDE 0884/ 06.92 (HCNW139/138 only). Insulation and Safety Related Specifications 8-Pin DIP Widebody (300 Mil) | SO-8 | (400 Mil) Parameter Symbol Value Value Value Units Conditions | Minimum External L101) 7.1 4.9 9.6 mm | Measured from input terminals | Air Gap (External to output terminals, shortest ' Clearance) distance through air. : Minimum External L(102) 7.4 4.8 10.0 mm | Measured from input terminals ' Tracking (External to output terminals, shortest . Creepage) distance path along body. * Minimum Internal 0.08 0.08 1.0 mm | Through insulation distance, Plastic Gap conductor to conductor, usually (Internal Clearance) the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal NA NA 4.0 mm _ | Measured from input terminals Tracking (Internal to output terminals, along ' Creepage) internal cavity. Tracking Resistance CTI 200 200 200 Volts | DIN IEC 112/VDE 0308 Part 1 - (Comparative _ Tracking Index) | Isolation Group Ila Ia Ila Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance with CECC 00802. ORIGINAL ONLY WHEN STAMPED IN REDVico Lrem Numpern All04 Rev #0 _ VDE 0884 Insulation Related Characteristics (HCNW139 and HCNW 138) Description Symbol | Characteristic | Units Installation Classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage < 600 V rms I-IV for rated mains voltage < 1000 V rms 1-1] Climatic Classification 55/100/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage ViorM 1414 V peak Input to Output Test Voltage, Method b* Vpr = 1.875 x Viorm, 100% Production Test with tp = 1 sec, Ver 2652 V peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* Ver = 1.5 x Viorm, Type and Sample Test, Ver 2121 V peak tp = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tiny = 10 sec) Viom 8000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 11, Thermal Derating curve.) Case Temperature Ts 175 C Current (Input Current Ip, Ps = 0) Is INPUT 400 mA Output Power Ps output 700 mw Insulation Resistance at Ts, Vigo = 500 V Rs > 10 Q *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, (VDE 0884) fora detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. ORIGINAL ONLY WHEN STAMPED IN REDVicon Lem Numpern AllO9 Rev #0 _ Absolute Maximum Ratings* (No Derating Required up to 85C) Parameter Symbol Min. Max Units Storage Temperature Ts -b5 125 C Operating Temperature** Ty -40 85 C ' Average Forward Input Current Trav) 20 mA ' Peak Forward Input Current Irpx 40 mA (50% Duty Cycle, 1 ms Pulse Width) _ Peak Transient Input Current lp;TRAN) 1.0 A (<1 ps Pulse Width, 300 pps) ' Reverse Input Voltage Vr 5 Vv HCNW139/138 3 Vv _ Input Power Dissipation P; 35 mW Output Current (Pin 6) Ip 60 mA / Emitter Base Reverse Voltage (Pin 5-7) Vas 0.5 Vv _ Supply Voltage and Output Voltage Veo -0.5 18 Vv | (6N139, HCPL-0701, HCNW139) Supply Voltage and Output Voltage Vec -0.5 7 v (6N138, HCPL-0700, HCNW138) Output Power Dissipation Po 100 mW Total Power Dissipation Py 135 mW Lead Solder Temperature (for Through Hole Devices) 260C for 10 sec., 1.6 mm below seating plane [ HCNW139/138 260C for 10 sec., up to seating plane _ Reflow Temperature Profile See Package Outline Drawings section ' (for SOIC-8 and Option #300) JEDEC Registered Data for 6N139 and 6N138. *0C to 70C on JEDEC Registration. Recommended Operating Conditions Parameter Symbol Min Max Units Power Supply Voltage Vec 4.5 18 V Forward Input Current (ON) Iron) 0.5 12.0 mA Forward Input Voltage (OFF) Vie(OFF) 0 0.8 Vv Operating Temperature Ts 0 70 C ORIGINAL ONLY WHEN STAMPED iN REDElectrical Specifications OC S$ Ta S$ 70C, 4.5 VS Veco $18 V,0.5mA< Ir(on) S$ 12 mA, 0 V < VevorR < 0.8 V, unless otherwise specified. All Typicals at Ty = 25C. See Note 7. Vicon Lrem Numer AlolO9 Rev #0 Parameter Sym.| Device Min.| Typ.**| Max. | Units Test Conditions Fig. | Note Current Transfer | CTR 6N139 400*| 2000 |5000| % | Ip=0.5mA Veco = 4.5 12,3 | 1,2, Ratio HCPL-0701 Vo = 0.4V 4 HCNW139 | 400} 4500 6N139 500*|} 1600 |2600 ly = 1.6mA HCPL-0701 HCNW139 | 500] 3000 300} 1600 Ip = 5.0 mA 200} 850 Ip = 12 mA 6N138 300*| 1600 }2600 Ir = 1.6mA HCPL-0700 HCNW138 1500 Logic Low Output | Vor 6N139 0.1 | 0.4 V |Ilp=O0.5mA, |Vec= 4.5 1 2 Voltage HCPL-0701 Ip =2mA HCNW139 Ir = 1.6 mA, Io =8mA Ip = 5.0 mA, Io = 15mA 0.2 Ip = 12 mA, Ip = 24 mA 6N138 0.1 Ip = 1.6 mA, HCPL-0700 Ip = 4.8 mA HCNW138 Logic High Jou 6N139 0.05 100 pA Vo = Vec =18V Ip =OmA 2 Output Current HCPL-0701 HCNW139 6N138 0.1 | 250 Vo=HVec=7V HCPL-0700 HCNW138 Logic Low Supply | Iec, | 6N138/139 0.4 15 | mA | Ip = 1.6 mA, Vo = Open, 10 2 Current HCPL-0701/ Ver = 18V 0700 HCNW139 0.5 2 HCNW138 Logic High Iccy | 6N138/1389 0.01 | 10 | BA | Ip =OmA, Vo= Open, 2 Supply Current HCPL-0701/ Vec=18V 0700 HCNW139 1 HCNW138 Input Forward Ve 6N138 1.25) 1.40 |1.7* ) V Ta = 25C | Ip = 1.6mA 4,8 Voltage 6N139 HCPL-0701 1.75 HCPL-0700 HCNW139 1.0] 1.45 | 1.85 Ta = 25C HCNW138 0.95 1.95 Input Reverse BVR 5.0* Vv Tp = 10 pA, Ty = 25C Breakdown HCNW139 | 3.0 Ip = 100 pA, Ta = 25C Voltage HCNW138 Temperature AVe -1.8 mv/C} Ip = 1.6 mA 8 Coefficient of ATs Forward Voltage Input Cw 60 pF | f= 1MHz,Vr=0V Capacitance HCNW139 90 HCNW1388 *JEDEC Registered Data for 6N139 and 6N138. **All typical values at Ta = 25C and Voc = 5 V, unless otherwise noted. ORIGIN AL ONLY WHEN STAMPED IN REDVico Lrem Numpern AllO4 Switching Specifications (AC) Over recommended operating conditions (T, = 0 to 70C), Vcc = 5 V, unless otherwise specified. Rev #0 _ Parameter Sym. | Device Min. | Typ.** | Max.| Units} Test Conditions |Fig. | Note Propagation Delay teu. 6N139 5 25* | us | Ty = 25C | 5,6, | 2,4 Time to Logic Low at HCPL-0701 30 Ip = 0.5 mA, 7,9, Output HCNW139 R] = 4.7kQ 12 6N139 0.2 1* | ws | Ty = 25C | HCPL-0701 Ip = 12 mA, RI = 270 Q HCNW139 11 6N138 1.6 10* | us | Ty = 25C HCPL-0700 [Ip = 1.6 mA, HCNW138 15 RI = 2.2 kQ HCNW138 11 Propagation Delay teLy 6N139 18 60* | us | Ty = 25C | 5, 6, | 2,4 Time to Logic High HCPL-0701 90 Ip = 0.5 mA, %9, at Output HCNW139 RIL = 4.7 kQ 2 HCNW139 115 6N139 2 7 | us | Ty = 25C | HCPL-0701 10 ly = 12 mA, HCNW139 RI = 270 Q HCNW139 1] 6N138 10 35* Ty = 25C HCPL-0700 eer) HCNW138 RI = 2.2 kQ 6N138 50 HCPL-0700 HCNW139 70 ' Common Mode |CMy| 1000 10000 Vi/us | Ip = 0 mA, 13 | 5,6 | Transient Immunity Ty = 25C ' at Logic High Output RI = 2.2 kQ lVom| = 10 Vp-p , Common Mode |CM, | 1000} 10000 V/us | Ip = 1.6 mA, 13 | 5,6 _ Transient Immunity Ty = 25C at Logic Low Output RI = 2.2 kQ |Vom| = 10 Vp-p *JEDEC Registered Data for 6N139 and 6N138. ** All typical values at Ty = 25C and Voc = 5 V, unless otherwise noted. ORIGINAL ONLY WHEN STAMPED IN REDVico Lem Numeer AlolO9 Package Characteristics Rev FQ 12 Parameter Sym. | Min. | Typ.**| Max.| Units Test Conditions Fig. | Note Input-Output Momentary Viso | 2500 Vrms | RH < 50%, t = 1 min., 3,8 Withstand Voltaget Ty = 25C Option 020 5000 3,9 HCNW139 HCNW138 Resistance (Input-Output) Rio 10! Q | Vio = 500 Vde 3 RH < 45% Capacitance (Input-Output) Cro 0.6 pF | f=1MHz 3 **All typicals at Ty = 25C, unless otherwise noted. +The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table Cif applicable}, your equipment level safety specification or Agilent Application Note 1074 entitled Optocoupler Input-Output Endurance Voltage. Notes: 1. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, Ip, to the forward LED input current, Ip, times 100%. 2. Pin 7 Open. . Device considered a two-terminal device. Pins 1, 2, 3, and 4 shorted logether and Pins 5, 6, 7, and 8 shorted together. . Use of a resistor between pin 5 and 7 will decrease gain and delay time. Significant reduction in overall gain can occur when using resistor values below 47 kQ. For more information, please contact your local HP Components representative. . Common mode transient immunity in a Logic High level is the maximum toler- able (positive) dVoy,/dt of the common mode pulse, Voy, to assure that the output will remain in a Logic High state (i.e., Vo > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVoy,/dt of the common mode pulse, Vom, to assure that the output will remain in a Logic Low state (i.e., Vo < 0.8 V). . In applications where dV/dt may exceed 50,000 VAus (such as static discharge) a series resistor, Roc, should be included to protect the detector IC from destructively high surge currents. The recommended value is Rec = 220 Q. . Use of a 0.1 uF bypass capacitor connected between pins 8 and 5 adjacent to the device is recommended. 8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 3000 V rms for | second (leakage detection current limit, Io < 5 WA). This test is per- formed before the 100% production test. shown in the VDE 0884 Insulation Related Characteristics Table, if applicable. . In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage detection current limit, [1.59 < 5 A). This test is per- formed before the 100% production test for partial discharge (method b) shown in the VDE 0884 Insulation Related Characteristics Table, if applicable. ORIGINAL ONLY WHEN STAMPED IN REDViceo, Lrem Numer AlolO4 ig - OUEPUE CURRENE - mA Vec=5V Ta = 25C Q 1.0 2.0 Vo OUTPUT VOLTAGE - V Figure 1. 6N138/6N139 DC Transfer Characteristics. 1000 < E 400/- ~ E wet 4 Z 40 SUL ie & HA J 2 1.05 Y < Y = 0.1 9 Tat 25C Ta = 0C4 ng 0.01 Le F a : 0.001 LA) YL Nye -40C| 1.1 1.2 1.3 1.4 1.5 1.6 Ve FORWARD VOLTAGE - V Figure 4. Input Diode Forward Current vs. Forward Voltage. Ip=12mA -+ RL = 270 kQ 1if = 50 ps tp - PROPAGATION DELAY ~ us 0 -60 -40 -20 0 20 40 60 80 100 Ta TEMPERATURE C Figure 7. Propagation Delay vs. Temperature. 2000 1600 1200 800 CTR - CURRENT TRANSFER RATIO % 0.1 1.0 10 Ip - FORWARD CURRENT - mA Figure 2, Current Transfer Ratio vs. Forward Current 6N138/6N139. 40 Ip = 0.5 mA 35 R, = 4.7 kQ 1if = 50 ps 30 25 20 15 10 tp PROPAGATION DELAY us 5 Q -60 -40 -20 0 20 40 60 80 100 Ta TEMPERATURE -~ C Figure 5. Propagation Delay vs. Temperature. 1.6 7 > SN ip = 1.6mA 8 15 NN 5 INQ a > MN a 14 wr N z INQ 2 13}+ Ss 1 N > 1.2 -60 -40 -20 0 20 40 60 80 100 Ta - TEMPERATURE C Figure 8. Forward Voltage vs. Temperature. Rey #O 13 q 1005: F 1 so e g 10: 7 ~ x Ff a E a L 1.0 pe 5 to Ee Ff Ta= 70C 8 94 Ta=2erc] very 4Ta=orc 2 Ta =-40C 0.01 AL fs a ml pti 0.01 04 1 10 Ip - INPUT DIODE FORWARD CURRENT - mA Figure 3. 6N138/6N139 Output Current vs. Input Diode Forward Current. 24 21 18 15 12 9 6 tp PROPAGATION DELAY - ps 3 tPHL 0 -60 -40 -20 0 20 40 GO 80 100 Ta TEMPERATURE ~ C Figure 6. Propagation Delay vs. Temperature. 100|- E Ta = 25C L tf 2 [ I Ww = e Ip - ADJUSTED FOR Vo, = 2V 4 J L jt 1 \ 0.1 1.0 10 R,, - LOAD RESISTANCE - kQ Figure 9. Nonsaturated Rise and Fall Times vs. Load Resistance. ORIGINAL ONLY WHEN STAMPEDVico Lrem Numer AlolO9 Rev #Q _ 4 # WIDEBODY ; 0.8 7 yl 1000 Ww i i : rere Pg (mi > 0.7 wef ee ef Zz 900 8 ) uw ' 2 m= Ig (mA) % 2 800 ee x 0.6 oe : > 3 A P 700 >~ 05 te poe agy > a Voc = 18 V ~). | a 600 3 O04 ot =i @ 500 = 03 : ; i mVec=5V 4 * 400 Bo * : = i i 300 QO OZ, sop mop = 8 ' | 9 200 7 otf | 5 100 a 0 : : : a 0 3 o 2 4 6 8 10 12 14 16 2 0 25 50 75 100 125 150 175 Tg - CASE TEMPERATURE ~ C Ip - FORWARD CURRENT Figure 10. Logic Low Supply Current Figure 11. Thermal Derating Curve, vs. Forward Current. Dependence of Safety Limiting Value with Case Temperature per VDE 0884. 1 , . | ruse |. a} ees v | Zo = 502 Vo Sv tr=5ns Ld RL Kh 40% DUTY CYCLE lif < 100 ps 3 |/6} Vo Lx] (SATURATED RESPONSE) po Vou = 0.1 pF I- MONITORO \ teHL i rt tei [4] 5 [ee = 15 pF* Ru = = Yo 5V / * INCLUDES PROBE AND FIXTURE CAPACITANCE (NON-SATURATED RESPONSE) tp Figure 12. Switching Test Circuit. ORIGINAL ONLY WHEN STAMPED IN REDVico Lem Numeern AlolO04 Rev #0 _ Roc (SEE NOTE 6) +5V rs 4 fal fe o o | s 4 7 Ver SWITCH AT A: Ip = 0 mA 5 Yo $$. Vo, SWITCH AT B: Ip = 1.6 mA cs Vom HAN wy) PULSE GEN. Figure 13. Test Circuit for Transient Immunity and Typical Waveforms. ORIGINAL ONLY WHEN STAMPED IN REDVicor Laem Numeern AlcI04 Rey #0 oe Agilent Technologies ORIGINAL ONLY WHEN STAMPED IN RED www.semiconductor.agilent.com Data subject to change. Copyright 2001 Agilent Technologies, Inc. September 6, 2001 Obsoletes 5968-1085E (5/00) 5988-4109EN