ISD1400 SERIES SINGLE-CHIP VOICE RECORD/PLAYBACK DEVICES 16- AND 20-SECOND DURATION -1- Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES TABLE OF CONTENTS 1. GENERAL DESCRIPTION.............................................................................................................................3 2. FEATURES........................................................................................................................................................3 3. BLOCK DIAGRAM..........................................................................................................................................4 4. PIN CONFIGURATION ..................................................................................................................................5 5. PIN DESCRIPTION..........................................................................................................................................6 6. FUNCTIONAL DESCRIPTION....................................................................................................................10 6.1. DETAILED DESCRIPTION ..............................................................................................................................10 6.2. OPERATIONAL MODES .................................................................................................................................11 6.2.1. Operational Modes Description ..........................................................................................................11 7. TIMING DIAGRAMS ....................................................................................................................................13 8. ABSOLUTE MAXIMUM RATINGS............................................................................................................14 8.1 OPERATING CONDITIONS ..............................................................................................................................15 9. ELECTRICAL CHARACTERISTICS .........................................................................................................16 9.1. PARAMETERS FOR PACKAGED PARTS ..........................................................................................................16 9.1.1. Typical Parameter Variation with Voltage and Temperature .............................................................19 9.2. PARAMETERS FOR DIE ................................................................................................................................20 9.2.1. Typical Parameter Variation with Voltage and Temperature .............................................................23 10. TYPICAL APPLICATION CIRCUIT ........................................................................................................24 11. PACKAGE DRAWING AND DIMENSIONS............................................................................................27 11.1. 28-LEAD 300 MIL PLASTIC SMALL OUTLINE IC (SOIC) ............................................................................27 11.2. 28-LEAD 600 MIL PLASTIC DUAL INLINE PACKAGE (PDIP).......................................................................28 11.3. DIE PHYSICAL LAYOUT [1] ..........................................................................................................................29 12. ORDERING INFORMATION.....................................................................................................................31 13. VERSION HISTORY....................................................................................................................................32 -2- ISD1400 SERIES 1. GENERAL DESCRIPTION Winbond's ISD1400 ChipCorder(R) series provide high-quality, single-chip, Record/Playback solutions to short-duration messaging applications. The CMOS devices include an on-chip oscillator, microphone preamplifier, automatic gain control, anti-aliasing filter, smoothing filter, and speaker amplifier. A minimum Record/Playback subsystem can be configured with a microphone, a speaker, several passive components, two push buttons and a power source. Recordings are stored into onchip non-volatile memory cells, providing zero-power message storage. This unique, single-chip solution is made possible through Winbond's patented Multi-Level Storage (MLS) technology. Voice and audio signals are stored directly into memory in their natural form, providing high-quality, solidstate voice reproduction. 2. FEATURES * Single +5 volt power supply * Duration: 14 and 20 seconds. * Easy-to-use single-chip, voice record/playback solution * High-quality, natural voice/audio reproduction * Manual switch or microcontroller compatible Playback can be edge- or level-activated * Directly cascadable for longer durations * Automatic power-down (push-button mode) o * Standby current 1 A (typical) Zero-power message storage o Eliminates battery backup circuits * Fully addressable to handle multiple messages * 100-year message retention (typical) * 100,000 record cycles (typical) * On-chip oscillator * Programmer support for play-only applications * Packaged types: Leaded and Lead-Free * Available in die, PDIP and SOIC * Temperature: o Commercial - Packaged unit : 0C to 70C, Die : 0C to 50C o Industrial - Packaged unit : -40C to 85C -3- Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES 3. BLOCK DIAGRAM Internal Clock Timing XCLK Sampling Clock Amp 5-Pole Active Antialiasing Filter ANA OUT MIC MIC REF Analog Transceivers 128K Cell Nonvolatile Multilevel Storage Array Decoders ANA IN PreAmp 5-Pole Active Smoothing Filter Automatic Gain Control (AGC) AGC Power Conditioning VCCA VSSA VSSD VCCD Device Control Address Buffers A0 A1 A2 A3 A4 A5 A6 A7 -4- REC PLAYE PLAYL RECLED SP + Amp SP - ISD1400 SERIES 4. PIN CONFIGURATION A0 1 28 VCCD A1 2 27 REC A2 3 26 XCLK A3 4 25 RECLED A4 5 24 PLAYE A5 6 23 PLAYL NC 7 22 NC NC 8 21 ANA OUT A6 9 20 ANA IN A7 10 19 AGC NC 11 18 MIC REF VSSD 12 17 MIC VSSA 13 16 VCCA SP + 14 15 SP- SOIC / PDIP Note: NC means must be No connect -5- Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES 5. PIN DESCRIPTION PIN NAME PIN NO FUNCTION A0-A7 1-6, 9, 10 Address Inputs: The address inputs have two functions, depending on the level of the two Most Significant Bits (MSB) of the address. If either or both of the two MSBs are LOW, the inputs are all interpreted as address bits and are used as the start address for the current record or playback cycle. The address pins are inputs only and do not output internal address information as the operation progresses. Address inputs are latched by the falling edge of PLAYE , PLAYL , or REC . If both A6 & A7 are HIGH, then the device is in special operational modes. Please refer to operational modes section for details. NC 7, 8, 11, 22 VSSD, VSSA 12, 13 Ground: Similar to VCCA and VCCD, the analog and digital circuits internal to the ISD1400 series use separate ground buses to minimize noise. These pins should be tied together as close as possible to the device. SP+, SP- 14, 15 Speaker Outputs: The SP+ and SP- pins provide direct drive for loudspeakers with impedances as low as 16 . A single output may be used, but, for direct-drive loudspeakers, the two opposite-polarity outputs provide an improvement in output power of up to four times over a single-ended connection. Forthermore, when SP+ and SP- are used, a speakercoupling capacitor is not required. A single-ended connection will require an AC-coupling capacitor between the SP pin and the speaker. The speaker outputs are in a highimpedance state during a record cycle, and held at VSSA during power down. VCCA, VCCD 16, 28 Supply Voltage: Analog and digital circuits internal to the ISD1400 series use separate power buses to minimize noise on the chip. These voltage buses are brought out to separate pins on the package and should be tied together as close to the supply as possible. It is important that the power supply be decoupled as close to the package as possible. MIC 17 Microphone: The microphone input transfers its signal to the on-chip preamplifier. An on-chip Automatic Gain Control (AGC) circuit controls the gain of this preamplifier from -15 to 24dB. An external microphone should be AC coupled to this pin via a series capacitor. The capacitor value, together with the internal 10 K resistance on this pin, determines the lowfrequency cutoff for the ISD1400 series passband. See Winbond's Application Information for additional information on low-frequency cutoff calculation. NC: No Connect -6- ISD1400 SERIES PIN NAME PIN NO FUNCTION MIC REF 18 Microphone Reference: The MIC REF input is the inverting input to the microphone preamplifier. This provides a noisecanceling or common-mode rejection input to the device when connected to a differential microphone. AGC 19 Automatic Gain Control (AGC): The AGC dynamically adjusts the gain of the preamplifier to compensate for the wide range of microphone input levels. The AGC allows the full range of sound, from whispers to loud sounds, to be recorded with minimal distortion. The "attack" time is determined by the time constant of a 5 K internal resistance and an external capacitor (C6 on the schematic of section 11, Figure 5) connected from the AGC pin to VSSA analog ground. The "release" time is determined by the time constant of an external resistor (R5) and an external capacitor (C6) connected in parallel between the AGC pin and VSSA analog ground. Nominal values of 470 K and 4.7 F give satisfactory results in most cases. ANA IN 20 Analog Input: The analog input pin transfers its signal to the chip for recording. For microphone inputs, the ANA OUT pin should be connected via an external capacitor to the ANA IN pin. This capacitor value, together with the 3.0 K input impedance of ANA IN, is selected to give additional cutoff at the low-frequency end of the voice passband. If the desired input is derived from a source other than a microphone, the signal can be fed, capacitively coupled, into the ANA IN pin directly. ANA OUT 21 Analog Output: This pin provides the preamplifier output to the user. The voltage gain of the preamplifier is determined by the voltage level at the AGC pin. PLAYL [2] 23 Playback, Level-Activated: When this input signal is held LOW, a playback cycle is initiated, and playback continues until PLAYL is pulled HIGH, or an EOM marker is detected. The device automatically powers down and enters into standby mode upon completion of a playback cycle. PLAYE [2] 24 Playback, Edge-Activated: When a LOW-going transition is input to this pin, a playback cycle begins. Taking PLAYE HIGH during a playback cycle will not terminate the current cycle. Playback continues until an EOM is encountered. Upon completion of a playback cycle, the device automatically powers down and enters into standby mode. -7- Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES PIN NAME PIN NO FUNCTION RECLED 25 Record LED: The RECLED output is LOW during a record cycle. It can be used to drive an LED to indicate a record cycle is in progress. In addition, RECLED pulses LOW momentarily when an end-of-message is encountered in a playback operation. XCLK 26 External Clock: The input has an internal pull-down device. The ISD1400 is configured at the factory with an internal sampling clock frequency that guarantees its minimum nominal record/playback time. For instance, an ISD1420 operating within specification will be observed to always have a minimum of 20 seconds of recording time. The sampling frequency is then maintained to a variation of +2.25 percent over the commercial temperature and operating voltage ranges, while still maintaining the minimum specified recording duration. This will result in some devices having a few percent more than nominal recording time. The Internal clock has a +5 percent tolerance over the industrial temperature and voltage range. A regulated power supply is recommended for industrial temperature parts. If greater precision is required, the device can be clocked through the XCLK pin as follows: EXTERNAL CLOCK SAMPLE RATES Sample Rate Required Clock ISD1416 Part Number 8.0 kHz 1024 kHz ISD1420 6.4 kHz 819.2 kHz These recommended clock rates should not be varied because the antialiasing and smoothing filters are fixed, and aliasing problems can occur if the sample rate differs from the one recommended. The duty cycle on the input clock is not critical, as the clock is immediately divided by two. If the XCLK is not used, this input must be connected to ground. -8- ISD1400 SERIES PIN NAME PIN NO FUNCTION REC 27 Record Input: The REC input is an active-LOW record signal. The device records whenever REC is LOW. This signal must remain LOW for the duration of the recording. REC takes precedence over either playback ( PLAYE or PLAYL ) signal. If REC is pulled LOW during a playback cycle, the playback immediately ceases and recording begins. A record cycle is completed when REC is pulled HIGH or the memory space is filled. And end-of-message marker (EOM) is internally recorded, enabling a subsequent playback cycle to terminate appropriately. The device automatically powers down to standby mode when REC goes HIGH. Notes: [1] The REC signal is debounced for 50 ms on the rising edge to prevent a false retriggering from a pushbutton switch. [2] During playback, if either PLAYE or PLAYL is held LOW during EOM or OVF, the device will still enter into standby mode and the internal oscillator and timing generator will stop. However, the rising edge of PLAYE and PLAYL are not debounced and any subsequent falling edge (particularly switch bounce) present on the input pins will initiate another playback. -9- Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES 6. FUNCTIONAL DESCRIPTION 6.1. DETAILED DESCRIPTION Speech/Sound Quality The Winbond's ISD1400 series offer 6.4 and 8.0 kHz sampling frequencies, allowing the user a choice of speech quality options. The speech samples are stored directly into on-chip non-volatile memory without the digitization and compression associated with other solutions. Direct analog storage provides a very true, natural sounding reproduction of voice, music, tones, and sound effects not available with most solidstate digital solutions. Duration To meet end system requirements, the ISD1400 series offer single-chip solutions at 16 and 20 seconds. TABLE 1: ISD1400 SERIES SUMMARY Part Number Duration (Seconds) Input Sample Rate (kHz) Typical Filter Pass Band* (kHz) ISD1416 16 8.0 3.3 ISD1420 20 6.4 2.6 * 3dB roll-off-point EEPROM Storage One of the benefits of Winbond's ChipCorder(R) technology is the use of on-chip non-volatile memory, providing zero-power message storage. The message is retained for up to 100 years typically without power. In addition, the device can be re-recorded typically over 100,000 times. Basic Operation The ISD1400 ChipCorder(R) series are controlled by a single control signal, REC , PLAYE (edgeactivated playback) or PLAYL (level-activated playback). The ISD1400 parts are configured for simplicity of design in a single/multiple-message application. Using the address lines will allow multiple message applications. Automatic Power-Down Mode At the end of a playback or record cycle, the ISD1400 series automatically return to a low-power standby mode, consuming typically 0.5 A. After a playback cycle, the device powers down automatically at the end of the message. After a record cycle, the device powers down immediately after REC is pulled to HIGH. - 10 - ISD1400 SERIES Addressing In addition to providing single message application, the ISD1400 series provide a full addressing capability. The ISD1400 series have 160 distinct addressable segments, providing the below resolutions. See Application Information for ISD1400 address tables. TABLE 2: DEVICE PLAYBACK/RECORD DURATIONS Part Number Minimum Duration (Seconds) ISD1416 100 ms ISD1420 125 ms 6.2. OPERATIONAL MODES The ISD1400 series have several built-in operational modes providing maximum functionality with a minimal additional components. The operational modes use the address pins, but are mapped to outside the normal address range. When the two Most Significant Bits (MSBs), A6 and A7, are HIGH, the remaining address signals are interpreted as mode bits and not as address bits. Therefore, operational modes and direct addressing are not compatible and cannot be used simultaneously. There are two important considerations for using operational modes. Firstly, all operations begin initially at address 0, which is the beginning address. Later operations can begin at other address locations, depending on the operational mode(s) chosen. In addition, the address pointer is reset to 0 when the device is changed from record to playback but not from playback to record when A4 is HIGH in Operational Mode. Secondly, an Operational Mode is executed when any of the control inputs, PLAYE , PLAYL or REC , goes LOW and the two MSBs are HIGH. This Operational Mode remains in effect until the next LOW-going control input signal, at which point the current address/mode levels are sampled and executed. 6.2.1. Operational Modes Description The Operational Modes can be used in conjunction with a microcontroller, or they can be hardwired to provide the desired system operation. A0 - Message Cueing Message Cueing allows the user to skip through messages, without knowing the actual physical addresses of each message. Each LOW pulse causes the internal address pointer to skip to the next message. This mode is used for playback only and typically used with the A4 Operational Mode. - 11 - Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES A1 - Delete EOM Markers The A1 Operational Mode allows recording messages sequentially and playback as a single message with only one EOM set at the end of the final message. A2 - Unused A3 - Message Looping The A3 Operational Mode allows repeating playback a message continuously from the beginning of the memory. A message can completely fill the ISD1400 device and will loop from beginning to end. Pulsing PLAYE will start the playback and pulsing PLAYL will end the playback. A4 - Consecutive Addressing During normal operation, the address pointer will reset when a message is played through to an EOM marker. The A4 Operational Mode inhibits the address pointer reset, allowing messages to be recorded or played back consecutively. When the device is in a static state; i.e., not recording or playback, momentarily taking this pin LOW will reset the address counter to zero. A5 - Unsued TABLE 3: OPERATIONAL MODES Mode Function Typical Use Jointly Compatible [1] A0 Message cueing Fast-forward through messages A4 A1 Delete EOM markers Position EOM marker at the end of the last message A3, A4 A2 Unused A3 Looping Continuous playback from Address 0 A1 A4 Consecutive addressing Record/playback multiple consecutive messages A0, A1 A5 Unused 1 Additional Operational Modes can be used simultaneously with the given mode. - 12 - ISD1400 SERIES 7. TIMING DIAGRAMS TREC TREC REC TLED1 TLED2 RECLED THOLD TSET THOLD TSET A0-A7 MIC ANA IN TRPUD TRPDD FIGURE 1: RECORD (1) REC TPLAY PLAYL PLAYE TSET THOLD THOLD TSET TSET THOLD A0-A7 SP+/TPPUD RECLED TPPDD TPPDD TPPUD (2) TEOM TEOM 1. REC must be HIGH for the entire duration of a playback cycle. 2. RECLED funstions as an EOM playback. FIGURE 2: PLAYBACK - 13 - Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES 8. ABSOLUTE MAXIMUM RATINGS2 TABLE 4: ABSOLUTE MAXIMUM RATINGS (PACKAGED PARTS) CONDITIONS VALUES Junction temperature 150C Storage temperature range -65C to +150C Voltage applied to any pin (VSS - 0.3V) to (VCC + 0.3V) Voltage applied to any pin (Input current limited to 20 mA) (VSS - 1.0V) to (VCC + 1.0V) Lead temperature (Soldering - 10sec) 300C VCC - VSS -0.3V to +7.0V TABLE 5: ABSOLUTE MAXIMUM RATINGS (DIE) CONDITIONS VALUES Junction temperature 150C Storage temperature range -65C to +150C Voltage applied to any pad (VSS - 0.3V) to (VCC + 0.3V) Voltage applied to any pad (Input current limited to 20mA) (VSS - 1.0V) to (VCC + 1.0V) Lead Temperature (soldering 10 seconds) 330 C VCC - VSS -0.3V to +7.0V 2 Stresses above those listed may cause permanent damage to the device. Exposure to the absolute maximum ratings may affect device reliability and performance. Functional operation is not implied at these conditions. - 14 - ISD1400 SERIES 8.1 OPERATING CONDITIONS TABLE 6: OPERATING CONDITIONS (PACKAGED PARTS) CONDITIONS VALUES Commercial operating temperature range (Case temperature) 0C to +70C Industrial operating temperature (Case temperature) -40C to +85C Supply voltage (VCC) Ground voltage (VSS) [1] +4.5V to +5.5V [2] 0V TABLE 7: OPERATING CONDITIONS (DIE) CONDITIONS VALUES Commercial operating temperature range Supply voltage (VCC) Ground voltage (VSS) [1] VCC = VCCA = VCCD [2] VSS = VSSA = VSSD 0C to +50C [1] +4.5V to +6.5V [2] 0V - 15 - Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES 9. ELECTRICAL CHARACTERISTICS 9.1. PARAMETERS FOR PACKAGED PARTS TABLE 8: DC PARAMETERS PARAMETERS SYMBOLS MIN[2] TYP[1] Input Low Voltage VIL Input High Voltage VIH Output Low Voltage VOL Output High Voltage VOH VCC Current (Operating) ICC 15 VCC Current (Standby) ISB 0.5 Input Leakage Current MAX[2] UNITS 0.8 V 2.4 CONDITIONS V 0.4 V IOL = 4.0 mA V IOH = -1.6 mA 30 mA VCC = 5.5V[3], REXT = 10 A [3] [4] IIL +1 A Input Current HIGH w/Pull Down IILPD 130 A Force VCC [5] Output Load Impedance REXT 16 Speaker Load Preamp IN Input Resistance RMIC 4 9 17 K ANA IN Input Resistance RANA IN 2.5 3 5 K Preamp Gain 1 APRE1 20 23 26 dB AGC = 0.0V Preamp Gain 2 APRE2 -45 -15 dB AGC = 2.5V ANA IN to SP+/- Gain AARP 20 22 25 dB AGC Output Resistance RAGC 2.5 5 9.5 K Preamp Out Source IPREH -2 mA @ VOUT = 1.0V Preamp In Sink IPREL 0.5 mA @ VOUT = 2.0V 2.4 Pins 17, 18 [1] Typical values @ TA = 25 and 5.0V. [2] All Min/Max limits are guaranteed by Winbond via electronical testing or characterization. Not all specifications are 100 percent tested. [3] VCCA and VCCD connected together. [4] REC , PLAYL , and PLAYE must be at VCCD. [5] XCLK pin . - 16 - ISD1400 SERIES TABLE 9: AC PARAMETERS CHARACTERISTICS Sampling Frequency SYMBOLS MIN[2] TYP[1] FS ISD1416 MAX[2] UNITS 8.0 6.4 kHz [5] kHz [5] ISD1420 Filter Pass Band CONDITIONS FCF ISD1416 3.3 kHz 3 dB Roll-Off Point[3][6] ISD1420 2.6 kHz 3 dB Roll-Off Point[3][6] Record Duration TREC ISD1416 16 sec ISD1420 20 sec ISD1416 16 sec [5] ISD1420 20 sec [5] Playback Duration TPLAY RECLED ON Delay TLED1 RECLED OFF Delay TLED2 ISD1416 5 30 40 38.9 48.6 msec 95 110 msec msec ISD1420 Address Setup Time TSET 300 nsec Address Hold Time THOLD 0 nsec Record Power-Up Delay TRPUD ISD1416 26 msec ISD1420 32 msec ISD1416 26 msec ISD1420 32 msec ISD1416 26 msec ISD1420 32 msec 6.5 8.1 msec Record Power-Down Delay Play Power-Up Delay Play Power-Down Delay TRPDD TPPUD TPPDD ISD1416 ISD1420 msec - 17 - Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES CHARACTERISTICS EOM Pulse Width SYMBOLS MIN[2] TYP[1] MAX[2] UNITS CONDITIONS TEOM ISD1416 ISD1420 12.5 msec 15.625 msec Total Harmonic Distortion THD 1 Speaker Output Power POUT 12.2 Voltage Across Speaker Pins VOUT 1.25 MIC Input Voltage ANA IN Input Voltage 3 % @ 1 kHz mW REXT = 16 2.5 V p-p REXT = 600 VIN1 20 mV Peak-to-Peak[5] VIN2 50 mV Peak-to-Peak Notes: [1] Typical values @ TA = 25 and 5.0V. [2] All Min/Max limits are guaranteed by Winbond via electronical testing or characterization. Not all specifications are 100 percent tested. [3] Low-frequency cutoff depends upon the value of external capacitors (see Pin Descriptions) [4] With 5.1 K series resistor at ANA IN. [5] Sampling Frequency and playback duration can vary as much as +2.25 percent over the commercial temperature and voltage rangs. It may vary as much as +5 percent over the industrial temperature and voltage ranges. All devices will meet the maximum sampling frequency and minimum playback duration parameters. For greater stability, an external clock can be utilized (see Pin Descriptions) [6] Filter specification applies to the anti-aliasing filter and the smoothing filter. Typical Parameter Variation with Voltage and Temperature. This parameter is not checked during production testing and may vary due to process variations and other factors. Therefore, the customer should not rely upon this value for testing purposes. - 18 - ISD1400 SERIES 9.1.1. Typical Parameter Variation with Voltage and Temperature Chart 3: Standby Current (ISB) 0.30 12 Standby Current (mA) Operating Current (mA) 14 Chart 1: Record Mode Operating Current (ICC) 10 8 6 4 2 0 0.25 0.20 0.15 0.10 0 -40 25 70 85 -40 Temperature (C) 5.5 Volts 4.5 Volts 5.5 Volts Chart 2: Total Harmonic Distortion 70 85 4.5 Volts Chart 4: Oscillator Stability 0.5 1.5 0.4 Percent Change (%) Percent Distortion (%) 25 Temperature (C) 0.3 0.2 0.1 0 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0 -40 25 70 85 -40 Temperature (C) 5.5 Volts 25 70 85 Temperature (C) 4.5 Volts 5.5 Volts - 19 - 4.5 Volts Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES 9.2. PARAMETERS FOR DIE TABLE 10: DC PARAMETERS PARAMETERS SYMBOLS MIN[2] TYP[1] Input Low Voltage VIL Input High Voltage VIH Output Low Voltage VOL Output High Voltage VOH VCC Current (Operating) ICC 15 VCC Current (Standby) ISB 0.5 Input Leakage Current MAX[2] UNITS 0.8 V 2.4 CONDITIONS V 0.4 V IOL = 4.0 mA V IOH = -1.6 mA 30 mA VCC = 5.5V[3], REXT = 10 A [3] [4] IIL +1 A Input Current HIGH w/Pull Down IILPD 130 A Force VCC [5] Output Load Impedance REXT 16 Speaker Load Preamp IN Input Resistance RMIC 4 9 17 K ANA IN Input Resistance RANA IN 2.5 3 5 K Preamp Gain 1 APRE1 20 23 26 dB AGC = 0.0V Preamp Gain 2 APRE2 -45 -15 dB AGC = 2.5V ANA IN to SP+/- Gain AARP 20 22 25 dB AGC Output Resistance RAGC 2.5 5 9.5 K Preamp Out Source IPREH -2 mA @ VOUT = 1.0V Preamp In Sink IPREL 0.5 mA @ VOUT = 2.0V 2.4 Pads 17,18 [1] Typical values @ TA = 25 and 5.0V. [2] All Min/Max limits are guaranteed by Winbond via electronical testing or characterization. Not all specifications are 100 percent tested. [3] VCCA and VCCD connected together. [4] REC , PLAYL , and PLAYE must be at VCCD. [5] XCLK pin. - 20 - ISD1400 SERIES TABLE 11: AC PARAMETERS CHARACTERISTICS Sampling Frequency SYMBOLS MIN[2] TYP[1] MAX[2] UNITS CONDITIONS FS ISD1416 8.0 kHz [5] ISD1420 6.4 kHz [5] ISD1416 3.3 kHz 3 dB Roll-Off Point[3][6] ISD1420 2.6 kHz 3 dB Roll-Off Point[3][6] Filter Pass Band Record Duration FCF TREC ISD1416 16 sec ISD1420 20 sec ISD1416 16 sec ISD1420 20 sec Playback Duration TPLAY RECLED ON Delay TLED1 RECLED OFF Delay TLED2 ISD1416 ISD1420 5 msec 30 38.9 95 msec 40 48.6 110 msec Address Setup Time TSET 300 nsec Address Hold Time THOLD 0 nsec Power-Up Delay TRPUD ISD1416 26 msec ISD1420 32 msec ISD1416 26 msec ISD1420 32 msec ISD1416 6.5 msec ISD1420 8.1 msec ISD1416 6.5 msec ISD1420 8.1 msec PD Pulse Width (Record) PD Pulse Width (Play) Play Power-Down Delay TRPUD TPPUD TPPDD - 21 - Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES CHARACTERISTICS EOM Pulse Width SYMBOLS MIN[2] TYP[1] MAX[2] UNITS CONDITIONS TEOM ISD1416 ISD1420 12.5 msec 15.625 msec Total Harmonic Distortion THD 1 Speaker Output Power POUT 12.2 Voltage Across Speaker Pins VOUT 1.25 MIC Input Voltage ANA IN Input Voltage 3 % @ 1 kHz mW REXT = 16 [4] 2.5 V p-p REXT = 600 VIN1 20 mV Peak-to-Peak[4] VIN2 50 mV Peak-to-Peak Notes: [1] Typical values @ TA = 25 and 5.0V. [2] All Min/Max limits are guaranteed by Winbond via electronical testing or characterization. Not all specifications are 100 percent tested. [3] Low-frequency cutoff depends upon the value of external capacitors (see Pin Descriptions) [4] With 5.1 K series resistor at ANA IN. [5] Sampling Frequency and playback duration can vary as much as +2.25 percent over the commercial temperature and voltage rangs. It may vary as much as +5 percent over the industrial temperature and voltage ranges. All devices will meet the maximum sampling frequency and minimum playback duration parameters. For greater stability, an external clock can be utilized (see Pin Descriptions) [6] Filter specification applies to the anti-aliasing filter and the smoothing filter. Typical Parameter Variation with Voltage and Temperature. This parameter is not checked during production testing and may vary due to process variations and other factors. Therefore, the customer should not rely upon this value for testing purposes. - 22 - ISD1400 SERIES 9.2.1. Typical Parameter Variation with Voltage and Temperature Chart 7: Standby Current (ISB) 0.35 Standby Current (mA) Operating Current (mA) 15 Chart 5: Record Mode Operating Current (ICC) 10 5 0 0.30 0.25 0.20 0.15 0.10 0 0 25 50 0 Temperature (C) 6.5 Volts 5.5 Volts 4.5 Volts 6.5 Volts Chart 6: Total Harmonic Distortion 50 5.5 Volts 4.5 Volts Chart 8: Oscillator Stability 0.5 0.4 Percent Change (%) Percent Distortion (%) 25 Temperature (C) 0.3 0.2 0.1 0 2.5 2.0 1.5 1.0 0.5 0 -0.5 -1.0 -1.5 0 25 50 0 Temperature (C) 6.5 Volts 5.5 Volts 25 50 Temperature (C) 4.5 Volts 6.5 Volts - 23 - 5.5 Volts 4.5 Volts Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES 10. TYPICAL APPLICATION CIRCUIT VCC D1 REC LED C7 0.001 F S1 PLAYL VCCD 28 VCCA 16 VSSD 12 1 A0 2 A1 R6 R7 R8 100 K 100 K 100 K S2 3 A2 4 A3 5 A4 6 A5 9 A6 SP+ 14 SP- 15 ANA IN 20 ISD1400 ANA OUT 21 24 PLAYE 27 REC S3 R2 5.1 K C3 0.1 F R3 10 K C4 0.1 F MIC REF 18 C1 220 F ELECTRET MICROPHONE MIC 17 RECORD 25 RECLED R9 1 K 16 SPEAKER VSSA 13 10 A7 23 PLAYL PLAYE R1 1K C2 0.1 F AGC 19 26 XCLK R5 470 K C6 4.7 F FIGURE 5: DESIGN SCHEMATIC - 24 - C5 0.1 F R4 10 K ISD1400 SERIES Functional Description Example The following operating examples demonstrate the functionality of the ISD1400 series. 1. Record a message: Pulling the REC signal LOW initiates a record cycle from current location. When REC is held LOW, the recording continues. Until the memory array is filled up or when REC is pulled HIGH, recording ceases. An EOM marker is written at the end of message. Then the device will automatically power down. 2. Edge-activated playback: Pulling the PLAYE signal LOW initiates a playback cycle from the beginning of the message until the entire message is played. The rising edge of PLAYE has no effect on operation. When the EOM marker is encountered, the device automatically powers down. A subsequent falling edge on PLAYE initiates a new playback operation from the beginning of the message. 3. Level-activated playback: Holding the PLAYL signal LOW initiates a playback cycle from the beginning of the message, until PLAYL is pulled HIGH or when the EOM marker is encountered, playback operation stops and the device automatically powers down. 4. Record (interrupting playback). The REC signal takes precedence over playback operation. Holding REC LOW initiates a new record operation from current location, regardless of any current operation in progress. 5. RECLED operation. During record, the RECLED output pin provides an active-LOW signal, which can be used to drive an LED as a "record-in-progress" indicator. It returns to a HIGH state when the REC pin is pulled HIGH or when the recording is completed due to the memory being filled. However, during playback, this pin also pulses LOW to indicate an EOM at the end of a message. - 25 - Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES Applications Note Some users may experience an unexpected recording taking place when their circuit is powered up, or the batteries are changed and VCC rises faster than REC . This undesired recording prevents playback of the previously recorded message. A spurious End Of Message (EOM) marker appears at the very beginning of the memory, preventing access to the original message, and nothing is played. To prevent this occurrence, place a capacitor (approx. 0.001 F) between the control pin ( REC ) and VCC. This pulls the control pin voltage up with VCC as it rises. Once the voltage is HIGH, the pull-up device will keep the pin HIGH until intentionally pulled LOW, preventing the false EOM marker. Since this anomaly depends on factors such as the capacitance of the user's printed circuit board, not all circuit designs will exhibit the spurious marker. However, it is recommended that the capacitor is included for design reliability. A more detailed explanation and resolution of this occurrence is described in Application Information. - 26 - ISD1400 SERIES 11. PACKAGE DRAWING AND DIMENSIONS 11.1. 28-LEAD 300 MIL PLASTIC SMALL OUTLINE IC (SOIC) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A G C B D E H F INCHES MILLIMETERS Min Nom Max Min Nom Max A 0.701 0.706 0.711 17.81 17.93 18.06 B 0.097 0.101 0.104 2.46 2.56 2.64 C 0.292 0.296 0.299 7.42 7.52 7.59 D 0.005 0.009 0.0115 0.127 0.22 0.29 E 0.014 0.016 0.019 0.35 0.41 0.48 F 0.050 1.27 G 0.400 0.406 0.410 10.16 10.31 10.41 H 0.024 0.032 0.040 0.61 0.81 1.02 Note: Lead coplanarity to be within 0.004 inches. - 27 - Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES 11.2. 28-LEAD 600 MIL PLASTIC DUAL INLINE PACKAGE (PDIP) INCHES A MILLIMETERS Min Nom Max Min Nom Max 1.445 1.450 1.455 36.70 36.83 36.96 B1 0.150 B2 0.065 C1 0.600 C2 0.530 0.070 0.540 D 3.81 0.075 1.65 0.625 15.24 0.550 13.46 1.78 15.88 13.72 0.19 D1 0.015 E 0.125 F 0.015 G 0.055 H 1.91 13.97 4.83 0.38 0.135 3.18 0.018 0.022 0.38 0.46 0.56 0.060 0.065 1.40 1.52 1.62 0.100 3.43 2.54 J 0.008 0.010 0.012 0.20 0.25 0.30 S 0.070 0.075 0.080 1.78 1.91 2.03 q 0 15 0 - 28 - 15 ISD1400 SERIES 11.3. DIE PHYSICAL LAYOUT [1] A3 ISD1400x o A2 Die Dimensions VCCD A1 A0 XCLK RECLED REC X: 172.2 1 mils Y: 168.5 1 mils A4 PLAYE A5 o PLAYL Die Thickness[2] 17.5 1 mils ISD1400X o Pad Opening 100 x 112 microns 3.9 x 4.4 mils A6 A7 NC ANA OUT ANA IN VSSD VSSA SPSP+ MIC VCCA AGC MIC REF Notes: [1] The backside of die is internally connected to VSS. It MUST NOT be connected to any other potential or damage may occur. [2] Die thickness is subject to change, please contact Winbond factory for status and availability. - 29 - Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES ISD1400 SERIES PAD DESIGNATIONS (with respect to die center) Pad Note: Pad Name X Axis (m) Y Axis (m) A0 Address 0 -1332.5 1973.8 A1 Address 1 -1628.9 1973.8 A2 Address 2 -1808.9 1973.8 A3 Address 3 -2014.1 1910.2 A4 Address 4 -2014.1 1722.6 A5 Address 5 -2014.1 1519.8 A6 Address 6 -2014.1 -1214.6 A7 Address 7 -2014.1 -1399.8 NC No Connect -2014.1 -1745.4 VSSD Digital Ground -1894.1 -1971.8 VSSA Analog Ground -358.1 -1971.8 SP+ Speaker Output + -17.7 -1896.6 SP- Speaker Output - 411.9 -1896.6 VCCA Analog Power Supply 779.5 -1936.2 MIC Microphone Input 991.5 -1973.8 MIC REF Microphone Reference 1168.7 -1973.8 AGC Automatic Gain Control 1977.9 -1910.6 ANA IN Analog Input 2005.1 -1580.2 ANA OUT Analog Output 1990.7 -1379.0 PLAYL Level-Activated Playback 2013.9 1608.6 PLAYE Edge-Activated Playback 2013.9 1777.0 RECLED Record LED Output 2011.9 1971.8 XCLK External Clock 1580.7 1973.8 REC Record 752.3 1973.8 VCCD Digital Power Supply -48.5 1929.4 Die dimensions and pad positions may be subjected to change. Please contact Winbond Sales Offices or Representatives to verify current or future specifications. - 30 - ISD1400 SERIES 12. ORDERING INFORMATION Product Number Descriptor Key ISD14 ISD1400 Series Duration: 16 = 20 = Special Temperature Field: Blank = Commercial Packaged (0C to +70) or Commercial Die (0C to +50) 16 seconds I 20 seconds = Industrial (-40C to +85) Leaded or Lead-Free Type: Blank = Leaded Package Type: Y = Lead-Free X = Die P = 28-Lead 600 mil Plastic Dual Inline Package (PDIP) S = 28-Lead 300 mil Small Outline Package (SOIC) When ordering the devices, please refer to the following valid order numbers. For the shaded part numbers, please contact the local Winbond Sales Representatives for availability information. Lead-Free Leaded Type Duration 16-Second 20-Second Package Part # Order # Part # Order # Die ISD1416X C5006 I1416X5006 ISD1420X C5006 I1420X5006 PDIP ISD1416P C5006 I1416P5006 ISD1420P C5006 I1420P5006 ISD1416PI C5006 I1416PI5006 ISD1420PI C5006 I1420PI5006 ISD1416S C5006 I1416S5006 ISD1420S C5006 I1420S5006 ISD1416SI C5006 I1416SI5006 ISD1420SI C5006 I1420SI5006 ISD1416PY I1416PY ISD1420PY I1420PY ISD1416PYI I1416PYI ISD1420PYI I1420PYI ISD1416SY I1416SY ISD1420SY I1420SY ISD1416SYI I1416SYI ISD1420SYI I1420SYI SOIC PDIP SOIC For the latest product information, access Winbond's worldwide website at http://www.winbond-usa.com - 31 - Publication Release Date: November 16, 2005 Revision 1.3 ISD1400 SERIES 13. VERSION HISTORY VERSION DATE DESCRIPTION 0 Before 2004 Initial issue. 1.0 March 2004 Reformat the document. Revise footnote for Filter Passband in Tables 1, 9 & 11. Revise Functional Description Example section. Revise die picture. Revise ordering information. 1.1 Apr 2005 Revise the disclaim section. 1.2 Jun 2005 Revise the part number for I1420 device in Ordering section. 1.3 Nov 2005 Add Pb-free info - 32 - ISD1400 SERIES Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Furthermore, Winbond products are not intended for applications wherein failure of Winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales. The contents of this document are provided only as a guide for the applications of Winbond products. Winbond makes no representation or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to discontinue or make changes to specifications and product descriptions at any time without notice. No license, whether express or implied, to any intellectual property or other right of Winbond or others is granted by this publication. Except as set forth in Winbond's Standard Terms and Conditions of Sale, Winbond assumes no liability whatsoever and disclaims any express or implied warranty of merchantability, fitness for a particular purpose or infringement of any Intellectual property. The contents of this document are provided "AS IS", and Winbond assumes no liability whatsoever and disclaims any express or implied warranty of merchantability, fitness for a particular purpose or infringement of any Intellectual property. In no event, shall Winbond be liable for any damages whatsoever (including, without limitation, damages for loss of profits, business interruption, loss of information) arising out of the use of or inability to use the contents of this documents, even if Winbond has been advised of the possibility of such damages. Application examples and alternative uses of any integrated circuit contained in this publication are for illustration only and Winbond makes no representation or warranty that such applications shall be suitable for the use specified. The 100-year retention and 100K record cycle projections are based upon accelerated reliability tests, as published in the Winbond Reliability Report, and are neither warranted nor guaranteed by Winbond. This product incorporates SuperFlash(R). Information contained in this ISD(R) ChipCorder(R) datasheet supersedes all data for the ISD ChipCorder products published by ISD(R) prior to August, 1998. This datasheet and any future addendum to this datasheet is(are) the complete and controlling ISD(R) ChipCorder(R) product specifications. In the event any inconsistencies exist between the information in this and other product documentation, or in the event that other product documentation contains information in addition to the information in this, the information contained herein supersedes and governs such other information in its entirety. This datasheet is subject to change without notice. Copyright(c) 2005, Winbond Electronics Corporation. All rights reserved. ChipCorder(R) and ISD(R) are trademarks of Winbond Electronics Corporation. SuperFlash(R) is the trademark of Silicon Storage Technology, Inc. All other trademarks are properties of their respective owners. Headquarters Winbond Electronics Corporation America Winbond Electronics (Shanghai) Ltd. No. 4, Creation Rd. III Science-Based Industrial Park, Hsinchu, Taiwan TEL: 886-3-5770066 FAX: 886-3-5665577 http://www.winbond.com.tw/ 2727 North First Street, San Jose, CA 95134, U.S.A. TEL: 1-408-9436666 FAX: 1-408-5441797 http://www.winbond-usa.com/ 27F, 299 Yan An W. Rd. Shanghai, 200336 China TEL: 86-21-62365999 FAX: 86-21-62356998 Taipei Office Winbond Electronics Corporation Japan Winbond Electronics (H.K.) Ltd. 9F, No. 480, Pueiguang Rd. Neihu District Taipei, 114 Taiwan TEL: 886-2-81777168 FAX: 886-2-87153579 7F Daini-ueno BLDG. 3-7-18 Shinyokohama Kohokuku, Yokohama, 222-0033 TEL: 81-45-4781881 FAX: 81-45-4781800 Unit 9-15, 22F, Millennium City, No. 378 Kwun Tong Rd., Kowloon, Hong Kong TEL: 852-27513100 FAX: 852-27552064 Please note that all data and specifications are subject to change without notice. All the trademarks of products and companies mentioned in this datasheet belong to their respective owners. This product incorporates SuperFlash(R) technology licensed From SST. - 33 - Publication Release Date: November 16, 2005 Revision 1.3