Series 1-DC * D1D to D5D series SSRs; MOSFET output * Ratings from 7A to 40A @ 200 VDC, and from 7A to 10A @ 500 VDC * DC Control * Relays are easily paralleled for higher-current applications * CE Compliant to EN60950-1 PRODUCT SELECTION Load Voltage 100 VDC 200 VDC 400 VDC 500 VDC 7A 10A D1D07 D2D07 D4D07 D5D07 12A 20A 40A D1D12 D2D12 D4D12 D1D20 D1D40 D2D40 D5D10 OUTPUT SPECIFICATIONS (1) Description Operating Voltage Range Maximum Off-State Leakage Current @ Rated Voltage [mA] Maximum Load Current (3) [Adc] Minimum Load Current [mA] Maximum Surge Current [Adc] (10ms) Maximum On-State Voltage Drop @ Rated Current [Vdc] Thermal Resistance Junction to Case (Rjc) [C/W] Maximum On-State Resistance [RDS-ON][Ohms] 7A 12A 20A 40A 7A 12A 40A 7A 12A 7A 10A 0-100 0.1 7 1 15 2.0 2.2 0.29 0-100 0.2 12 1 28 1.6 1.34 0.13 0-100 0.3 20 1 42 2.1 1.06 0.10 0-100 0.3 40 1 106 2.1 0.83 0.05 0-200 0.1 7 1 22 2.0 1.5 0.29 0-200 0.3 12 1 27 2.8 1.06 0.23 0-200 0.3 40 1 106 2.1 0.83 0.05 0-400 0.3 7 1 17 4.2 1.06 0.6 0-400 0.3 12 1 36 4.2 0.8 0.35 0-500 0.2 7 1 19 5.7 1.0 0.8 0-500 0.3 10 1 29 5.5 0.8 0.55 INPUT SPECIFICATIONS (1) Description DC Control Control Voltage Range Minimum Turn-On Voltage Minimum Turn-Off Voltage Minimum Input Current @ 5VDC Maximum Input Current @ 32VDC Nominal Input Impedance Maximum Turn-On Time [sec] Maximum Turn-Off Time [msec] 3.5-32 VDC 3.5 VDC 1.0 VDC 1.6 mA 28 mA See Note 4 100 1.0 GENERAL SPECIFICATIONS Description Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 V DC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Encapsulation Terminals Recommended Terminal Screw Torque Range: Parameters 2500 VRMS 109 Ohm 50 pF -20 to 80C -20 to 125 C 3.0 oz (86.5g) Thermally conductive Epoxy Screws and Saddle Clamps Furnished, Unmounted 6-32 Screws - 10 in lbs. 8-32 and 10-32 Screws -20 in. lbs. (Screws dry without grase) GENERAL NOTES 1) All parameters at 25C and per section unless otherwise specified. 2) Dielectric strength and insulation resistance are measured between input and output 3) Heat sinking required, for derating curves see page 3. 4) Input circuitry version incorporates active current limiter. MECHANICAL SPECIFICATIONS THERMAL DERATE INFORMATION WIRING DIAGRAM MAXIMUM SURGE VS DURATION AGENCY APPROVALS EN60950 : Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7: Designed in accordance with the requirements of IEC 62314 UL E116950 (100 Volt Models 1-DC Only ) Rev. 120711 ANNEX - ENVIROMENTAL INFORMATION