Radial Leads/Ceralam(R) GENERAL INFORMATION Dimensions: Millimeters (Inches) AVX MR Series 1.14 (.045) Max. Molded Radial Leaded MLC W L T 31.7 (1.25) Min. Temperature Coefficients: C0G (NP0), X7R, Z5U 50, 100, 200 Volts L.D. L T 31.7 (1.25) Min. L.S. Case Material: Molded Epoxy W Style MR05 Lead Material: Solderable L.D. L.S. Styles MR04, MR06, MR07, MR08 HOW TO ORDER MR05 AVX Style MR04 MR05 MR06 MR07 MR08 1 1 Voltage 5 = 50V 1 = 100V 2 = 200V A Dielectric A = C0G (NP0) C = X7R E = Z5U 561 J Capacitance Capacitance Tolerance First two digits are the significant figures of capacitance. Third digit indicates the additional number of zeros. For example, order 100,000 pF as 104. (For values below 10pF use "R" in place of decimal point, e.g., 1R4 = 1.4pF.) C0G (NP0): D = .5pF (>10pF only) F = 1% (>50pF only) G = 2% (>25pF only) J = 5% K = 10% A X7R: J = 5% K = 10% M = 20% A Failure Rate Leads A = Not Applicable T = CECC A = Standard Solderable (SnPb) T1 = Trimmed Leads .230" .030" Z5U: M = 20% Z = +80% -20% Trimmed lead length for the MR05 style will be measured from the bend in the lead (seating plane). MARKING PACKAGING REQUIREMENTS Marking is as size permits. (For code identification, see HOW TO ORDER section.) Bulk Packaging: 1000 pcs. per sealed package except MR07/MR08 (300 pcs.). Tape and Reel: Available on MR04, MR05, and MR06 only (2500 pcs./reel). Ammo Packaging: Available on special request. -- AVX -- Capacitance Tolerance -- Voltage Rating -- Temperature Coefficient -- Date Code -- Lot Code 29 Radial Leads/Ceralam(R) C0G (NP0) SIZE AND CAPACITANCE SPECIFICATIONS Dimensions: Millimeters (Inches) Cap. in pF 1.0 to 9.1 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10,000 12,000 15,000 18,000 22,000 27,000 33,000 39,000 47,000 56,000 68,000 82,000 100,000 120,000 150,000 AVX Style Length* Width* Thickness* Lead Spacing* Lead Diameter* Typical AVX Part Nos. MR-----5A1R0DAA MR04 4.83 (.190") 4.83 (.190") 2.28 (.090") 2.54 (.100") .635 (.025") WVDC 200 100 50 MR05 4.83 (.190") 4.83 (.190") 2.28 (.090") 5.08 (.200") .635 (.025") WVDC 200 100 50 MR06 7.36 (.290") 7.36 (.290") 2.28 (.090") 5.08 (.200") .635 (.025") WVDC 200 100 50 MR07 12.44 (.490") 12.44 (.490") 3.55 (.140") 10.16 (.400") .635 (.025") WVDC 200 100 50 MR-----5A9R1DAA MR-----5A100KAA MR-----5A120KAA MR-----5A150KAA MR-----5A180KAA MR-----5A220KAA MR-----5A270KAA MR-----5A330KAA MR-----5A390KAA MR-----5A470KAA MR-----5A560KAA MR-----5A680KAA MR-----5A820KAA MR-----5A101KAA MR-----5A121KAA MR-----5A151KAA MR-----5A181KAA MR-----5A221KAA MR-----5A271KAA MR-----5A331KAA MR-----5A391KAA MR-----5A471KAA MR-----5A561KAA MR-----5A681KAA MR-----5A821KAA MR-----5A102KAA MR-----5A122KAA MR-----5A152KAA MR-----5A182KAA MR-----5A222KAA MR-----5A272KAA MR-----5A332KAA MR-----5A392KAA MR-----5A472KAA MR-----5A562KAA MR-----5A682KAA MR-----5A822KAA MR-----5A103KAA MR-----5A123KAA MR-----5A153KAA MR-----5A183KAA MR-----5A223KAA MR-----5A273KAA MR-----5A333KAA MR-----5A393KAA MR-----5A473KAA MR-----5A563KAA MR-----5A683KAA MR-----5A823KAA MR-----5A104KAA MR-----5A124KAA MR-----5A154KAA For trimmed leads see "How To Order". For other tolerances see "How To Order". For other voltages see "How To Order". = Industry preferred values *Length, width and thickness dimensions are .254 mm (.010"). Lead diameter is .05 mm (.002"). Lead spacing is .381 mm (.015"). 30 MR08 12.44 (.490") 12.44 (.490") 6.09 (.240") 10.16 (.400") .635 (.025") WVDC 200 100 50 Radial Leads/Ceralam(R) X7R SIZE AND CAPACITANCE SPECIFICATIONS Dimensions: Millimeters (Inches) Cap. in pF 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10,000 12,000 15,000 18,000 22,000 27,000 33,000 39,000 47,000 56,000 68,000 82,000 100,000 120,000 150,000 180,000 220,000 270,000 330,000 390,000 470,000 560,000 680,000 820,000 1.0 F 1.2 F 1.5 F 1.8 F 2.0 F 2.2 F 2.7 F 3.3 F 3.9 F 4.7 F AVX Style Length* Width* Thickness* Lead Spacing* Lead Diameter* Typical AVX Part Nos. MR-----5C101KAA MR-----5C121KAA MR-----5C151KAA MR-----5C181KAA MR-----5C221KAA MR-----5C271KAA MR-----5C331KAA MR-----5C391KAA MR-----5C471KAA MR-----5C561KAA MR-----5C681KAA MR-----5C821KAA MR-----5C102KAA MR-----5C122KAA MR-----5C152KAA MR-----5C182KAA MR-----5C222KAA MR-----5C272KAA MR-----5C332KAA MR-----5C392KAA MR-----5C472KAA MR-----5C562KAA MR-----5C682KAA MR-----5C822KAA MR-----5C103KAA MR-----5C123KAA MR-----5C153KAA MR-----5C183KAA MR-----5C223KAA MR-----5C273KAA MR-----5C333KAA MR-----5C393KAA MR-----5C473KAA MR-----5C563KAA MR-----5C683KAA MR-----5C823KAA MR-----5C104KAA MR-----5C124KAA MR-----5C154KAA MR-----5C184KAA MR-----5C224KAA MR-----5C274KAA MR-----5C334KAA MR-----5C394KAA MR-----5C474KAA MR-----5C564KAA MR-----5C684KAA MR-----5C824KAA MR-----5C105KAA MR-----5C125KAA MR-----5C155KAA MR-----5C185KAA MR-----5C205KAA MR-----5C225KAA MR-----5C275KAA MR-----5C335KAA MR-----5C395KAA MR-----5C475KAA MR04 4.83 (.190") 4.83 (.190") 2.28 (.090") 2.54 (.100") .635 (.025") WVDC 200 100 50 MR05 4.83 (.190") 4.83 (.190") 2.28 (.090") 5.08 (.200") .635 (.025") WVDC 200 100 50 For trimmed leads see "How To Order". For other tolerances see "How To Order". For other voltages see "How To Order". MR06 7.36 (.290") 7.36 (.290") 2.28 (.090") 5.08 (.200") .635 (.025") WVDC 200 100 50 MR07 12.44 (.490") 12.44 (.490") 3.55 (.140") 10.16 (.400") .635 (.025") WVDC 200 100 50 MR08 12.44 (.490") 12.44 (.490") 6.09 (.240") 10.16 (.400") .635 (.025") WVDC 200 100 50 = Industry preferred values *Length, width and thickness dimensions are .254 mm (.010"). Lead diameter is .05 mm (.002"). Lead spacing is .381 mm (.015"). 31 Radial Leads/Ceralam(R) Z5U SIZE AND CAPACITANCE SPECIFICATIONS Dimensions: Millimeters (Inches) AVX Style MR04 4.83 (.190") 4.83 (.190") 2.28 (.090") 2.54 (.100") .635 (.025") WVDC Length* Width* Thickness* Cap. in pF Lead* Spacing Lead* Diameter Typical AVX Part Nos. 10,000 12,000 15,000 18,000 22,000 27,000 33,000 39,000 47,000 56,000 68,000 82,000 100,000 120,000 150,000 180,000 220,000 270,000 330,000 390,000 470,000 560,000 680,000 820,000 1.0 F 1.2 F 1.5 F 1.8 F 2.2 F 2.7 F 3.3 F 3.9 F 4.7 F 5.6 F 6.8 F 8.2 F 10.0 F MR-----5E103ZAA MR-----5E123ZAA MR-----5E153ZAA MR-----5E183ZAA MR-----5E223ZAA MR-----5E273ZAA MR-----5E333ZAA MR-----5E393ZAA MR-----5E473ZAA MR-----5E563ZAA MR-----5E683ZAA MR-----5E823ZAA MR-----5E104ZAA MR-----5E124ZAA MR-----5E154ZAA MR-----5E184ZAA MR-----5E224ZAA MR-----5E274ZAA MR-----5E334ZAA MR-----5E394ZAA MR-----5E474ZAA MR-----5E564ZAA MR-----5E684ZAA MR-----5E824ZAA MR-----5E105ZAA MR-----5E125ZAA MR-----5E155ZAA MR-----5E185ZAA MR-----5E225ZAA MR-----5E275ZAA MR-----5E335ZAA MR-----5E395ZAA MR-----5E475ZAA MR-----5E565ZAA MR-----5E685ZAA MR-----5E825ZAA MR-----5E106ZAA 100 MR05 4.83 (.190") 4.83 (.190") 2.28 (.090") 5.08 (.200") .635 (.025") WVDC 50 100 For trimmed leads see "How To Order". For other tolerances see "How To Order". For other voltages see "How To Order". MR06 7.36 (.290") 7.36 (.290") 2.28 (.090") 5.08 (.200") .635 (.025") WVDC 50 100 MR07 12.44 (.490") 12.44 (.490") 3.55 (.140") 10.16 (.400") .635 (.025") WVDC 50 100 MR08 12.44 (.490") 12.44 (.490") 6.09 (.240") 10.16 (.400") .635 (.025") WVDC 50 50 = Industry preferred values *Length, width and thickness dimensions are .254 mm (.010"). Lead diameter is .05 mm (.002"). Lead spacing is .381 mm (.015). 32 100 SkyCap(R) Configurations by Lead Spacing LEAD SPACING .100 .030 Dimensions: Inches (Millimeters) AR07/SR07* AR14/SR14 AR15/SR15* AR20/SR20* (T=.100) (T=.100) (T=.100) (T=.125) .200 (5.08) Max. .150 (3.81) Max. .250 (6.35) Max. .200 (5.08) Max. .150 (3.81) Max. .050 (1.27) Clean Above Seating Plane Meniscus Free .031 (.787) Above Seating Plane 1.0 (25.4) Min. .150 (3.81) Max. .300 (7.62) Max. .060 (1.52) Max. .230 (5.84) .030 .100 (2.54) .030 .200 (5.08) Max. 1.0 (25.4) Min. .100 (2.54) .030 1.0 (25.4) Min. .060 (1.52) Max. .100 (2.54) .030 AR29/SR29* AR62/SR62* SR62-LP* (T=.125) (T=.125) (T=.100) .210 (5.33) Max. .170 (4.32) Max. .200 (5.08) Max. 0.04 (1.02) .358 (9.09) Max. a 1.0 (25.4) Min. 0.008 0.002 (.203 .051) Meniscus Free .031 (.787) Above Seating Plane 1.0 (25.4) Min. .100 (2.54) .030 0.100 .031 (2.54 .787) .100 (2.54) .030 Leads = #22 AWG LEAD SPACING .271 (6.88) Max. 0.040 (1.016)Min. .250 (6.35) Max. .100 (2.54) .030 Leads = #22 AWG .200 .030 Dimensions: Inches (Millimeters) AR12/SR12* SR13* AR21/SR21* SR21-85* SR28* (T=.100) (T=.125) (T=.125) (T=.125) (T=.125) .200 (5.08) Max. .200 (5.08) Max. .150 (3.81) Max. .150 (3.81) Max. .200 (5.08) Max. .230 (5.84) Max. 1.0 (25.4) Min. Meniscus Free .031 (.787) Above Seating Plane .350 (8.89) Max. .200 (5.08) .030 .031 (.787) Clean Above Seat .200 (5.08) Max. .300 (7.62) Max. .300 (7.62) Max. Meniscus Free .031 (.787) Above Seating Plane 1.0 (25.4) Min. .200 (5.08) Max. .250 (6.35) Max. Meniscus Free .031 (.787) Above Seating Plane 1.0 (25.4) Min. 1.0 (25.4) Min. 1.0 (25.4) Min. .200 (5.08) .030 .200 (5.08) .030 .200 (5.08) .030 .200 (5.08) .030 AR30/SR30* SR30-LP* AR32/SR32* AR40/SR40* AR59/SR59* (T=.150) (T=.150) (T=.150) (T=.150) (T=.125) .300 (7.62) Max. .300 (7.62) MAX. .300 (7.62) Max. .225 (5.71) MAX. .300 (7.62) Max. 1.0 (25.4) Min. 1.0 (25.4) Min. .059 (1.5) Max. .060 (1.52) Max. .400 (10.16) Max. .390 (9.91) Max. Meniscus Free .031 (.787) Above Seating Plane .200 (5.08) Max. .400 (10.16) Max. .031 (.787) Clean Above Seat .300 (7.62) Max. 1.0 (25.4) Min. .200 (5.08) .030 .200 (5.08) .030 .200 (5.08) .030 1.0 (25.4) Min. 1.0 (25.4) Min. .060 (1.52) Max. .200 (5.08) .030 .200 (5.08) .030 SR61 SR63* SR64* SR64-LP* (T=.150) (T=.150) (T=.150) (T=.150) .300 (7.62) Max. .500 (12.7) Max. .500 (12.7) Max. Meniscus Free .031 (.787) Above Seating Plane .300 (7.62) Max. .300 (7.62) Max. .230 (5.84) .030 .500 (12.7) Max. 0.040 (1.02) Min. .200 (5.08) .030 .200 (5.08) .030 .330 (8.38) Max. 0.04 (1.02) .300 (7.62) Max. .400 (10.16) Max. a 1.00 (25.4) Min. 1.0 (25.4) Min. (T=.150) .300 (7.62) Max. .268 (6.81) Max. a .137/.196 (3.48/4.98) AR65/SR65* .200 (5.08) .031 a = .009 .002 (.229 .051) Leads = #22 AWG 1.0 (25.4) Min. 1.0 (25.4) Min. .200 (5.08) .030 .200 (5.08) .030 Leads = #22 AWG *SL style available in all SR configurations. 27 SkyCap(R) Configurations by Lead Spacing .200 .030 continued LEAD SPACING SR65-LP* (T=.150) .300 (7.62) MAX. Dimensions: Inches (Millimeters) SR67 AR75/SR75* AR89/SR89* (T=.125) (T=.150) Leads = #22 AWG (T=.125) .200 (5.08) Max. .400 (10.16) Max. .300 (7.62) Max. Seated Height .031 (.787) Seated Plane .350 (8.89) MAX. COATING LIMIT .031 (.787) Min. Clean Lead Above Seat 1.0 (25.4) Min. .215 (5.46) Max. 0.040 (1.02) Min. .400 (10.16) Max. .480 (12.2) Max. .230 (5.84) .030 .260 (6.60) Max. a 1.00 (25.4) Min. 0.025 0.001 (.635 .025) .200 (5.08) .031 .200 (5.08) .030 .200 (5.08) .030 Meniscus Free .031 (7.87) Above Seating Plane LEAD SPACING .250 .030 a = .009 .002 (.229 .051) 1.0 (25.4) Min. .200 (5.08) .030 Leads = #22 AWG Dimensions: Inches (Millimeters) SR16 SR22 SR33 (T=.125) (T=.125) (T=.150) .200 (5.08) Max. Meniscus Free .031 (.787) Above Seating Plane .390 (9.91) Max. .200 (5.08) Max. .300 (7.62) Max. .400 (10.16) Max. .300 (7.62) Max. .230 (5.84) .030 1.0 (25.4) Min. .250 (6.35) .030 .230 (5.84) .030 .250 (6.35) .030 LEAD SPACING .250 (6.35) .030 .300 .030 SR27 SR34 (T=.150) (T=.150) .260 (6.60) Max. .300 (7.62) Max. Meniscus Free .031 (.787) Above Seating Plane .250 (6.35) Max. 1.0 (25.4) Min. Meniscus Free .031 (.787) Above Seating Plane .350 (8.89) Max. 1.0 (25.4) Min. .300 (7.62) .030 .300 (7.62) .030 .375 .030 LEAD SPACING LEAD SPACING .400 .030 AR38/SR38 SR50 SR76 (T=.150) (T=.200) (T=.175) .500 (12.7) Max. .500 (12.7) Max. .300 (7.62) Max. Meniscus Free .031 (.787) Above Seating Plane .500 (12.7) Max. .425 (10.8) Max. 1.0 (25.4) Min. 1.0 (25.4) Min. .060 (1.52) Max. .440 (11.2) Max. .031 (.787) Min. Clean Lead Above Seat .375 (9.53) .030 Leads = #22 AWG 1. All leads are #24 AWG unless otherwise noted. 2. Available in tape and reel packaging(*). 3. Other styles are also available, contact factory. 4. (T = XXX) under type designation is maximum thickness in inches. *SL style available in all SR configurations. 28 Seating Plane 1.0 (25.4) Min. .025 (0.64) .004 .400 (10.16) .030 .400 (10.16) .030 NOTES: .480 (12.2) Max. Radial Leads/Packaging Tape and Reel GENERAL INFORMATION THE INSERTABLES 1. Standard reel diameter is 355 millimeters (14 inches) maximum. STANDARD 1 2. Reeling standard (#1 or #2) should be specified when ordering. 32 mm max. HOW TO ORDER 16 0.5 mm To specify tape and reel packaging, add TR1, TR2 or TRX to the end of the AVX 12 digit part number. SR07 Examples: SR29 SR59 SR65 SR75 STANDARD 2 SR215C104KARTR1 SR305E105MARTR2 SR215C103JARTRX 32 mm max. 19 mm min. to base of unit SR07 SR29 STANDARD 1 SR59 SR65 SR75 Dimensions in Millimeters 32 max. 32 max. 20 +1.5 -1.0 16.5 SR28 SR29 SR12 SR21 SR13 SR32 16 min. SR21 (TRX) MR05 SR32 (TRX) SR63 (TRX) SR15 SR20 STANDARD 2 32 max. MR06 SR30 SR40 Dimensions in Millimeters 32 max. 19 min. 19 min. SR29 SR28 SR12 SR21 SR13 SR32 SR15 SR20 MR05 S T S K E D R C W A B F O N M SR30 SR40 DESCRIPTION DIMENSIONS (MM) A. Feed Hole Pitch B. Feed Hole Diameter C. Feed Hole Location 12.70 .20 3.99 .20 9.02 .51 D. Component Lead Spacing +.79 5.00+.79 -.20 or 2.54 -.20 E. Component Lead Location 3.81 .51 or 5.00 .51 for 2.54 lead spacing 2.00 maximum F. Component Lead Protrusion (edge of carrier to cut end of lead) K. Component Body Location Q L MR06 X L. Carrier Tape Width M. Carrier Tape Assembly Thickness N. Carrier Tape Spliced Thickness O. Carrier Tape Spliced Length Q. Adhesive Tape Border R. Component Bent Leads (either direction) S. Component Misalignment T. Component Pitch W. Adhesive Tape Width X. Carrier Tape Thickness Y. Cumulative Pitch over 20 Pitches 6.35 .41 18.01 +1.02 -.51 .71 .20 1.42 maximum 50.80 - 88.90 3.00 maximum .79 maximum .99 maximum 12.70 .99 5.00 minimum .51 .10 254 2.00 33 Radial Leads/Packaging REEL DIRECTION QUANTITY PER REEL SR/AR Leads on top of carrier strip, body away Unreel from LEFT to RIGHT OVER TOP of reel PART PCS SR15, 07, 12 3500 SR20, 21, 23, 28 13, 29, 59, 62, 89 3000 SR30, 32, 40, 63, 64 65, 75 2000 MR05, 06 2500 *SL style available in all SR configurations. G DESCRIPTION A - Reel Diameter B - Reel Outside Width C - Reel Inside Width D - Core Diameter (O.D.) E - Hub Recess Diameter F - Hub Recess Depth G - Arbor Hole Diameter A F DIMENSIONS (MM) 304.80 - 355 50.80 maximum 38.10 - 46.02 102.01 maximum 86.36 maximum 9.50 minimum 25.40 - 30.48 D C B E CONVERSION TABLE MM .10 .20 .38 .41 .51 .71 .79 .99 1.02 1.42 34 IN .004 .007 .015 .016 .020 .028 .031 .039 .040 .056 MM 1.52 2.00 2.54 3.00 3.18 3.48 3.81 3.99 4.45 4.98 IN MM IN MM .060 .079 .100 .118 .125 .137 .150 .157 .175 .196 5.00 5.08 6.22 6.35 6.60 6.99 7.62 8.89 9.02 9.50 .197 .200 .245 .250 .260 .275 .300 .350 .355 .374 9.91 10.03 10.16 11.68 12.50 12.70 16.00 18.01 25.40 30.48 IN .390 .395 .400 .460 .492 .500 .630 .709 1.000 1.200 MM 32.00 38.10 46.02 50.80 86.36 88.90 102.01 254.00 304.80 355.00 IN 1.260 1.500 1.812 2.000 3.400 3.500 4.016 10.000 12.000 14.000