DS3695ATM/NOPB - Texas Instruments - Datasheet.Technology

DS3695A, DS3695AT, DS3696A

www.ti.com

SNLS353C –FEBRUARY 1996–REVISED APRIL 2013

DS3695A/DS3695AT/DS3696A Multipoint RS485/RS422 Transceivers

Check for Samples: DS3695A,DS3695AT,DS3696A

1FEATURES DESCRIPTION

The DS3695A and DS3696A are high speed

2• Meets EIA Standard RS485 for Multipoint Bus differential TRI-STATE bus/line transceivers designed

Transmission and is Compatible with RS-422 to meet the requirements of EIA standard RS485 with

• 10 Ns Driver Propagation Delays (Typical) extended common mode range (+12V to −7V), for

• Single +5V Supply multipoint data transmission. In addition they are

compatible with requirements of RS-422.

•−7V to +12V Bus Common Mode Range

Permits ±7V Ground Difference between The driver and receiver outputs feature TRI-STATE

Devices on the Bus capability. The driver outputs remain in over the

entire common mode range of +12V to −7V. Bus

• Thermal Shutdown Protection faults that cause excessive power dissipation within

• High Impedance to Bus with Driver in TRI- the device trigger a thermal shutdown circuit, which

STATE or with Power Off, over the Entire forces the driver outputs into the high impedance

Common Mode Range Allows the Unused state. The DS3696A provides an output pin (TS)

Devices on the Bus to be Powered Down which reports the thermal shutdown of the device. TS

is an “open collector” pin with an internal 10 kΩpull-

• Combined Impedance of a Driver Output and up resistor. This allows the TS outputs of several

Receiver Input is less than One RS485 Unit devices to be wire OR-ed.

Load, Allowing up to 32 Transceivers on the

Bus Both AC and DC specifications are guaranteed over

the 0°C to 70°C temperature and 4.75V to 5.25V

• 70 mV Typical Receiver Hysteresis supply voltage range.

• Available in SOIC Packaging

Connection and Logic Diagrams

Figure 1. Molded Package, Small Outline (D0008A) Figure 2. Top View

Top View (See Package Number D0008A)

TS was LF (Line Fault) on previous datasheets, TS goes low upon thermal shutdown.

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

DS3695A, DS3695AT, DS3696A

SNLS353C –FEBRUARY 1996–REVISED APRIL 2013

www.ti.com

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

Absolute Maximum Ratings (1)(2)

Supply Voltage, VCC 7V

Control Input Voltages 7V

Driver Input Voltage 7V

Driver Output Voltages +15V/−10V

Receiver Input Voltages +15V/−10V

Receiver Output Voltage 5.5V

Continuous Power Dissipation @ 25°C

D0008A Package 630 mW (3)

Storage Temp. Range −65°C to +150°C

Lead Temp. (Soldering 4 seconds) 260°C

(1) “Absolute maximum ratings” are those beyond which the safety of the device cannot be verified. They are not meant to imply that the

device should be operated at these limits. The tables of “Electrical Characteristics” provide conditions for actual device operation.

(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and

specifications.

(3) Derate linearly at 6.5 mW/°C to 337 mW at 70°C.

Recommended Operating Conditions Min Max Units

Supply Voltage, VCC 4.75 5.25 V

Bus Voltage −7 +12 V

Operating Free Air Temperature (TA)

Commercial (DS3695AM) 0 +70 °C

Industrial (DS3695ATM) −40 +85 °C

Commercial (DS3696AM) 0 +70 °C

Electrical Characteristics (1) (2)

0°C ≤TA≤70°C, 4.75V < VCC < 5.25V unless otherwise specified

Parameter Test Conditions Min Typ Max Units

VOD1 Differential Driver Output Voltage (Unloaded) IO= 0 5 V

VOD2 Differential Driver Output Voltage (with Load) R = 50Ω; (RS-422) (3) 2 V

R = 27Ω; (RS-485) 1.5 V

ΔVOD Complementary Output States R = 27Ω0.2 V

Differential Output Voltage For

Change in Magnitude of Driver

VOC Driver Common Mode Output Voltage 3.0 V

Δ|VOC| Change in Magnitude of Driver 0.2 V

Common Mode Output Voltage

For Complementary Output States

VIH Input High Voltage DI, DE, RE , 2 V

RE/DE

VIL Input Low Voltage 0.8 V

VCL Input Clamp Voltage IIN =−18 mA −1.5 V

IIL Input Low Current VIL = 0.4V −200 μA

IIH Input High Current VIH = 2.4V 20 μA

(1) All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless

otherwise specified.

(2) All typicals are given for VCC = 5V and TA= 25°C.

(3) All limits for which this note is applied must be derated by 10% for DS3695AT. Other parameters remain the same for this extended

temperature range device (−40°C ≤TA≤+85°C).

Product Folder Links: DS3695A DS3695AT DS3696A

DS3695A, DS3695AT, DS3696A

www.ti.com

SNLS353C –FEBRUARY 1996–REVISED APRIL 2013

Electrical Characteristics (1) (2) (continued)

0°C ≤TA≤70°C, 4.75V < VCC < 5.25V unless otherwise specified

Parameter Test Conditions Min Typ Max Units

IIN Input Current RI, RI, DO/RI, VCC = 0V or 5.25V, VIN = 12V +1.0 mA

DO/RI DE or RE /DE = 0V VIN =−7V −0.8 mA

VTH Differential Input Threshold Voltage for Receiver −7V ≤VCM ≤+12V −0.2 +0.2 V

ΔVTH Receiver Input Hysteresis VCM = 0V 70 mV

VOH Receiver Output High Voltage IOH =−400 μA 2.4 V

VOL Output Low Voltage RO IOL = 16 mA (3) 0.5 V

TS IOL = 8 mA 0.45 V

IOZR Output Current at Receiver OFF-State (High 0.4V ≤VO≤2.4V, VCC = Max, ±20 μA

Impedance)

RIN Receiver Input Resistance −7V ≤VCM ≤+12V 12 kΩ

ICC Supply Current Driver Outputs 42 60 mA

Enabled

No Load(3) Driver Outputs 27 40 mA

Disabled

IOSD VO=−7V (3) −250 mA

Output Current Driver Short-Circuit VO= +12V (3) +250 mA

IOSR Output Current Receiver Short-Circuit VO= 0V −15 −85 mA

Receiver Switching Characteristics

0°C ≤TA≤70°C, 4.75V < VCC < 5.25V unless otherwise specified (4)

Symbol Test Conditions Min Typ Max Units

tPLH CL= 15 pF 15 28 42 ns

tPHL S1 and S2 15 28 42 ns

|tPLH–tPHL| Closed 0 3 ns

tPLZ CL= 15 pF, S2 Open 5 29 35 ns

tPHZ CL= 15 pF, S1 Open 5 12 16 ns

tPZL CL= 15 pF, S2 Open 7 15 28 ns

tPZH CL= 15 pF, S1 Open 7 15 20 ns

(4) All typicals are given for VCC = 5V and TA= 25°C.

Driver Switching Characteristics

0°C ≤TA≤70°C, 4.75V < VCC < 5.25V unless otherwise specified (1)

Symbol Test Conditions Min Typ Max Units

SINGLE ENDED CHARACTERISTICS (Figure 7,Figure 8, and Figure 10)

tPLH RLDIFF = 60Ω9 15 22 ns

tPHL CL1 = CL2 = 100 pF 9 15 22 ns

tSKEW|tPLH–tPHL| 0 2 8 ns

tPLZ CL= 15 pF, S2 Open 7 15 30 ns

tPHZ CL= 15 pF, S1 Open 7 15 30 ns

tPZL CL= 100 pF, S2 Open 30 35 50 ns

tPZH CL= 100 pF, S1 Open 30 35 50 ns

DIFFERENTIAL SWITCHING CHARACTERISTICS (Figure 10)

tr, tfRLDIFF = 60Ω6 10 18 ns

CL1 = CL2 = 100 pF

(1) All typicals are given for VCC = 5V and TA= 25°C.

Product Folder Links: DS3695A DS3695AT DS3696A

DS3695A, DS3695AT, DS3696A

SNLS353C –FEBRUARY 1996–REVISED APRIL 2013

www.ti.com

AC TEST CIRCUITS AND SWITCHING WAVEFORMS

Figure 3. Receiver Propagation Delay Test Circuit

Differential input voltage may be realized by grounding RI and pulsing RI between +2.5V and −2.5V

Figure 4. Receiver Input-to-Output Propagation Delay Timing

Figure 5. Receiver Enable/Disable Propagation Delay Timing

Figure 6. Unless Otherwise Specified the Switches are Closed

Product Folder Links: DS3695A DS3695AT DS3696A

DS3695A, DS3695AT, DS3696A

www.ti.com

SNLS353C –FEBRUARY 1996–REVISED APRIL 2013

Figure 7. Driver Propagation Delay Test Circuits

tPLH and tPHL are measured to the respective 50% points. tSKEW is the difference between propagation delays of the

complementary outputs.

Figure 8. Driver Input-to-Output Propagation Delay Timing (Single-Ended)

Figure 9. Driver Enable/Disable Propagation Delay Timing

Figure 10. Driver Differential Transition Timing

Product Folder Links: DS3695A DS3695AT DS3696A

DS3695A, DS3695AT, DS3696A

SNLS353C –FEBRUARY 1996–REVISED APRIL 2013

www.ti.com

Table 1. Function Tables DS3695A/DS3696A Transmitting(1)

Inputs Line Outputs

RE DE DI Condition DO DO TS * (DS3696A Only)

X 1 1 No Fault 0 1 H

X 1 0 No Fault 1 0 H

X 0 X X Z Z H

X 1 X Fault Z Z L

Table 2. Function Tables DS3695A/DS3696A Receiving(1)

Inputs Outputs

RE DE RI–RI RO TS * (DS3696A Only)

0 0 ≥+0.2V 1 H

0 0 ≤−0.2V 0 H

0 0 Inputs Open** 1 H

1 0 X Z H

(1) X — Don't care condition

Z — High impedance state

Fault — Improper line conditions causing excessive power dissipation in the driver, such as shorts or bus contention situations

* TS is an “open collector” output with an on-chip 10 kΩpull-up resistor.

** This is a fail safe condition

(1) X — Don't care condition

Z — High impedance state

Fault — Improper line conditions causing excessive power dissipation in the driver, such as shorts or bus contention situations

* TS is an “open collector” output with an on-chip 10 kΩpull-up resistor.

** This is a fail safe condition

Typical Application

Repeater control logic not shown.

Figure 11.

Product Folder Links: DS3695A DS3695AT DS3696A

DS3695A, DS3695AT, DS3696A

www.ti.com

SNLS353C –FEBRUARY 1996–REVISED APRIL 2013

REVISION HISTORY

Changes from Revision B (April 2013) to Revision C Page

• Changed layout of National Data Sheet to TI format ............................................................................................................ 6

Product Folder Links: DS3695A DS3695AT DS3696A

PACKAGE OPTION ADDENDUM

www.ti.com 1-Sep-2018

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

DS3695AM/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS36

95AM

DS3695AMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS36

95AM

DS3695ATM/NOPB OBSOLETE SOIC D 8 TBD Call TI Call TI -40 to 85 DS369

5ATM

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

PACKAGE OPTION ADDENDUM

www.ti.com 1-Sep-2018

Addendum-Page 2

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

DS3695AMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 10-Aug-2018

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

DS3695AMX/NOPB SOIC D 8 2500 367.0 367.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 10-Aug-2018

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its

semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers

should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated

circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and

services.

Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is

accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced

documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements

different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the

associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers

remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have

full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products

used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with

respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous

consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and

take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will

thoroughly test such applications and the functionality of such TI products as used in such applications.

TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,

including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to

assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any

way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource

solely for this purpose and subject to the terms of this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically

described in the published documentation for a particular TI Resource.

Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that

include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE

TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,

INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF

PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,

DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN

CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949

and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.

Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such

products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards

and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must

ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in

life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.

Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life

support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all

medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.

TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).

Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications

and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory

requirements in connection with such selection.

Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-

compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

DS3695ATM DS3695ATM/NOPB DS3695ATMX DS3695ATMX/NOPB