Three-phase synchronous motor AC COMPACT DRIVES Type 1PH818., 1PH822. A5E02446774A AB Operating Instructions * 10/2009 ac motor 12.10.2009 17:04 Three-phase synchronous motor AC COMPACT DRIVES 1PH818., 1PH822. Operating Instructions Edition 10/2009 Introduction 1 Safety notes 2 Description 3 Preparations for use 4 Assembling 5 Connection 6 Commissioning 7 Operation 8 Maintenance 9 Spare parts 10 Disposal 11 Appendix A Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken. CAUTION without a safety alert symbol, indicates that property damage can result if proper precautions are not taken. NOTICE indicates that an unintended result or situation can occur if the corresponding information is not taken into account. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation for the specific task, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be adhered to. The information in the relevant documentation must be observed. Trademarks All names identified by (R) are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Industry Sector Postfach 48 48 90026 NURNBERG GERMANY Ordernumber: A5E02446774A AB 10/2009 Copyright (c) Siemens AG 2008, 2009. Technical data subject to change Table of contents 1 Introduction................................................................................................................................................ 9 2 Safety notes............................................................................................................................................. 11 3 4 5 6 2.1 The five safety rules:....................................................................................................................11 2.2 Qualified personnel ......................................................................................................................12 2.3 Safe handling ...............................................................................................................................12 2.4 Working on machines with permanent magnets..........................................................................14 2.5 Electrostatic sensitive devices .....................................................................................................15 2.6 2.6.1 2.6.2 Electromagnetic compatibility (EMC)...........................................................................................16 Interference immunity ..................................................................................................................16 Emitted interference.....................................................................................................................16 Description............................................................................................................................................... 17 3.1 Applications..................................................................................................................................17 3.2 Rating plate ..................................................................................................................................17 3.3 Layout ..........................................................................................................................................18 Preparations for use ................................................................................................................................ 21 4.1 4.1.1 Shipment and packaging .............................................................................................................21 Scope of supply ...........................................................................................................................21 4.2 4.2.1 4.2.2 4.2.3 Transport and storage..................................................................................................................21 Transporting .................................................................................................................................21 Storage.........................................................................................................................................24 Protecting the cooling-water system............................................................................................26 Assembling .............................................................................................................................................. 27 5.1 Heat-resistant mounting parts......................................................................................................27 5.2 Installing .......................................................................................................................................27 5.3 Alignment preconditions...............................................................................................................28 5.4 Aligning the machine with the driven load ...................................................................................28 5.5 Securing the machine ..................................................................................................................29 5.6 Pushing on the power output elements .......................................................................................30 5.7 Condensation drain holes ............................................................................................................31 Connection .............................................................................................................................................. 33 6.1 6.1.1 6.1.2 Mechanical connection ................................................................................................................33 Cooling water quality....................................................................................................................33 Connecting the cooling water supply ...........................................................................................34 6.2 6.2.1 Electrical connection ....................................................................................................................35 Safety note for the DRIVE-CLiQ interface ...................................................................................35 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 3 Table of contents 6.2.2 6.2.3 6.2.4 6.2.5 6.2.6 6.2.7 6.2.8 6.2.9 6.2.10 6.2.11 6.2.12 6.2.13 7 8 9 10 Commissioning ........................................................................................................................................ 43 7.1 Measures to be performed prior to commissioning..................................................................... 43 7.2 Trial run ....................................................................................................................................... 45 7.3 Checking insulation resistance ................................................................................................... 45 7.4 Switching on................................................................................................................................ 47 Operation................................................................................................................................................. 49 8.1 Safety notes during operation ..................................................................................................... 49 8.2 Do not operate without cooling water supply .............................................................................. 50 8.3 Stoppages ................................................................................................................................... 51 8.4 Switching off................................................................................................................................ 51 8.5 8.5.1 8.5.2 Faults........................................................................................................................................... 51 Electrical faults ............................................................................................................................ 51 Mechanical faults ........................................................................................................................ 53 Maintenance ............................................................................................................................................ 55 9.1 9.1.1 9.1.1.1 9.1.1.2 9.1.1.3 9.1.1.4 9.1.2 9.1.2.1 9.1.2.2 9.1.2.3 9.1.2.4 9.1.2.5 9.1.2.6 Inspection and maintenance ....................................................................................................... 55 Inspection .................................................................................................................................... 55 Initial inspection........................................................................................................................... 55 General inspection ...................................................................................................................... 56 Rolling-contact bearing inspection .............................................................................................. 56 Changing bearings when using permanently lubricated rolling-contact bearings....................... 57 Maintenance................................................................................................................................ 57 Safety instructions for maintenance............................................................................................ 57 Maintenance intervals ................................................................................................................. 57 Rolling-contact bearings.............................................................................................................. 58 Cleaning the spent grease chamber ........................................................................................... 58 Lubrication................................................................................................................................... 59 Maintaining the cooling water system ......................................................................................... 60 9.2 9.2.1 9.2.2 9.2.3 9.2.4 9.2.5 Repair.......................................................................................................................................... 61 Removing and installing the protecting ring ................................................................................ 61 Connecting the speed encoder ................................................................................................... 62 Replacing or adjusting the speed encoder.................................................................................. 62 Replacing the DRIVE-CLiQ interface (encoder module) ............................................................ 63 Screw-type connections .............................................................................................................. 63 Spare parts .............................................................................................................................................. 65 10.1 4 Cable entry and routing............................................................................................................... 35 Electrical connection data ........................................................................................................... 36 Terminal designation................................................................................................................... 37 Connection with cable lugs ......................................................................................................... 37 Connect up the ground conductor............................................................................................... 38 Internal equipotential bonding ..................................................................................................... 39 Circuit diagram ............................................................................................................................ 39 Connecting the speed encoder ................................................................................................... 40 Connecting the temperature sensor............................................................................................ 40 Connection to a converter ........................................................................................................... 41 Converter operation on a grounded network .............................................................................. 41 Final steps ................................................................................................................................... 42 Ordering data .............................................................................................................................. 65 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Table of contents 11 A 10.2 Spare parts kits ............................................................................................................................65 10.3 Ordering spare parts from Spares on Web..................................................................................66 10.4 Motor, complete ...........................................................................................................................67 10.5 Rolling-contact bearing bush drive end, mounted gearing, with regreasing................................68 10.6 Rolling-contact bearing bush drive end, belt coupling .................................................................69 10.7 Rolling-contact bearing bush drive end, coupling output, with regreasing ..................................70 10.8 Rolling-contact bearing bush drive end, coupling output, with permanent lubrication.................71 10.9 Rolling-contact bearing bush non-drive end, with permanent lubrication ....................................72 10.10 Rolling-contact bearing bush non-drive end, with regreasing (shaft height 180, 225) ................73 10.11 Terminal box ................................................................................................................................74 10.12 Speed encoder.............................................................................................................................75 Disposal................................................................................................................................................... 77 11.1 Introduction ..................................................................................................................................77 11.2 Preparing for disassembly ...........................................................................................................77 11.3 Working on machines with permanent magnets..........................................................................77 11.4 Disposing of permanent magnets ................................................................................................78 11.5 Disposal of components...............................................................................................................79 Appendix.................................................................................................................................................. 81 A.1 Siemens Service Center ..............................................................................................................81 A.2 EC Declaration of Conformity ......................................................................................................82 Index........................................................................................................................................................ 89 Tables Table 3-1 Elements on the rating plate ........................................................................................................17 Table 3-2 Machine design ............................................................................................................................18 Table 3-3 Types of construction...................................................................................................................19 Table 3-4 Roller bearing versions ................................................................................................................20 Table 4-1 Tightening torque for rotor shipping brace...................................................................................24 Table 5-1 Noise emissions...........................................................................................................................27 Table 5-2 Permissible deviations when aligning the motor..........................................................................29 Table 6-1 Cooling water specification ..........................................................................................................33 Table 6-2 Rate of flow and pressure drop....................................................................................................34 Table 6-3 Electrical connection data ............................................................................................................37 Table 6-4 Terminal designations using the 1U1-1 as an example...............................................................37 Table 6-5 Tightening torque for the terminal box cover fixing screws .........................................................42 Table 7-1 Stator winding insulation resistance at 25 C ..............................................................................46 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 5 Table of contents Table 8-1 Electrical faults ............................................................................................................................ 52 Table 8-2 Mechanical faults ........................................................................................................................ 53 Table 9-1 Measures after operating times or intervals................................................................................ 58 Table 9-2 Rolling-contact bearing greases ................................................................................................. 59 Table 9-3 Tightening torque for screwed union connections ...................................................................... 63 Table 10-1 Motor, complete .......................................................................................................................... 67 Table 10-2 Spare parts for rolling-contact bearing bush drive end with mounted gearing, with regreasing ................................................................................................................................... 68 Table 10-3 Spare parts for rolling-contact bearing bush drive end with belt coupling, with regreasing........ 69 Table 10-4 Spare parts for rolling-contact bearing bush drive end, with coupling output, with regreasing ................................................................................................................................... 70 Table 10-5 Spare parts for rolling-contact bearing bush drive end, with coupling output, with permanent lubrication.................................................................................................................. 71 Table 10-6 Spare parts for rolling-contact bearing bush non-drive end, permanent lubrication ................... 72 Table 10-7 Spare parts for rolling-contact bearing bush non-drive end, with regreasing, shaft height 180 / 225 ..................................................................................................................................... 73 Table 10-8 Spare parts for terminal box........................................................................................................ 74 Table 10-9 Spare parts for the speed encoder ............................................................................................. 75 Table A-1 Siemens Service Center contact details ..................................................................................... 81 Figures Figure 3-1 Schematic layout of rating plate.................................................................................................. 17 Figure 4-1 Lifting the machine ...................................................................................................................... 23 Figure 4-2 Rotor shipping brace ................................................................................................................... 24 Figure 5-1 Aligning the machine................................................................................................................... 29 Figure 5-2 Water drain holes ........................................................................................................................ 31 Figure 6-1 Connection using cable lugs ....................................................................................................... 38 Figure 6-2 Detailed view: Connection point for ground conductor........................................................... 39 Figure 6-3 Detailed view: Plug-in connection ............................................................................................... 40 Figure 9-1 Grease nipple.............................................................................................................................. 60 Figure 9-2 Fitting the protecting ring............................................................................................................. 61 Figure 9-3 Electrical connection of the speed sensor .................................................................................. 62 Figure 10-1 Schematic diagram of motor (complete) ..................................................................................... 67 Figure 10-2 Rolling-contact bearing bush drive end with mounted gearing, with regreasing ........................ 68 Figure 10-3 Rolling-contact bearing bush drive end with belt coupling, with regreasing ............................... 69 Figure 10-4 Rolling-contact bearing bush drive end, with coupling output, with regreasing .......................... 70 Figure 10-5 Rolling-contact bearing bush drive end, with coupling output, with permanent lubrication ........ 71 6 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Table of contents Figure 10-6 Rolling-contact bearing bush non-drive end, permanent lubrication ...........................................72 Figure 10-7 Rolling-contact bearing bush non-drive end, with regreasing, shaft height 180 / 225.................73 Figure 10-8 Terminal box ................................................................................................................................74 Figure 10-9 Speed encoder.............................................................................................................................75 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 7 Table of contents 8 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 1 Introduction About these operating instructions These operating instructions describe the machine and explain best practices in machine handling, from initial delivery to final disposal of the equipment. Read these operating instructions before you handle the machine to become familiar with its design and operating principles and thus ensure safe, problem-free machine operation and long service life. If you find any mistakes or have suggestions for improvements, please contact the Siemens Service Center. Text format features The warning notice system is explained on the rear of the inside front. Always follow the safety instructions and notices in these operating instructions. In addition to the safety-related warning notices which you must read, you will find the text in these operating instructions is formatted in the following way: 1. Handling instructions are always formatted as a numbered list. Always perform the steps in the order given. Lists are formatted as bulleted lists. - Lists on the second level are hyphenated. Note A Note is an important item of information about the product, handling of the product or the relevant section of the document. Notes provide you with help or further suggestions/ideas. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 9 Introduction 10 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Safety notes 2 This electric machine has been designed and built in accordance with the specifications in the Low-Voltage Directive 2006/95/EG and is intended for use in industrial systems as an incomplete machine in terms of Machinery Directive 98/37/EG . In accordance with the Machinery Directive we are obliged to point out that commissioning in the European Community is forbidden until it has been established that the system in which the machine is to be fitted conforms with the Machinery Directive. Please observe the country-specific regulations when using the electric machine outside the European Community. Follow the local and industry-specific safety and setup regulations. The persons responsible for the plant must ensure the following: Planning and configuration work and all work carried out on and with the machine is only to be done by qualified personnel. The operating instructions must always be available for all work. The technical data as well as the specifications relating to the permissible installation, connection, ambient and operating conditions are taken into account at all times. The specific setup and safety regulations as well as regulations on the use of personal protective equipment are observed. Note Use the services and support provided by the Siemens Service Center for planning, installation, commissioning and servicing work. In the individual chapters of this document, you will find safety instructions that must be obeyed absolutely, for your own safety, to protect other people and to avoid damage to property. Observe the following safety instructions for all activities on and with the machine. 2.1 The five safety rules: For your personal safety and to prevent material damage when working on the machine, always observe the safety instructions and the following five safety rules, according to DIN VDE 0105. Apply the five safety rules in the order stated before starting work at the machine. Five safety rules 1. Disconnect the system. Be sure to disconnect auxiliary circuits, e.g. anti-condensation heaters, etc. 2. Protect against reconnection. 3. Make sure that the equipment is at zero voltage A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 11 Safety notes 2.2 Qualified personnel 4. Ground and short-circuit 5. Cover or enclose adjacent components that are still live. When work has been completed, remove these measures in reverse order. 2.2 Qualified personnel All work at the machine should be carried out by qualified personnel only. For the purpose of this documentation, qualified personnel is taken to mean people who fulfill the following requirements: Through appropriate training and experience, they are able to recognize and avoid risks and potential dangers in their particular field of activity. They have been instructed to carry out work on the machine by the appropriate person responsible. 2.3 Safe handling Workplace safety depends on the attentiveness, care, and common sense of the personnel who install, operate, and maintain the machine. In addition to the safety measures cited, as a matter of principle, the use of caution is necessary when you are near the machine. Always pay attention to your safety. Also observe the following to prevent accidents: General safety regulations applicable in the country where the machine is deployed. Manufacturer-specific and application-specific regulations Special agreements made with operator Separate safety instructions supplied with the machine WARNING Live parts Electric machines contain live parts. Fatal or severe injuries and substantial material damage can occur if the covers are removed or if the machine is not handled, operated, or maintained properly. Always observe the "five safety rules (Page 11)" when carrying out any work on the machine. Only remove the covers using the methods described by these operating instructions. Operate the machine properly. Perform regular maintenance on the machine. 12 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Safety notes 2.3 Safe handling WARNING Rotating components Electric machines contain dangerous rotating parts. Fatal or severe injuries and substantial material damage can occur if the covers are removed or if the machine is not handled, operated, or maintained properly. Only remove the covers using the methods described by these operating instructions. Operate the machine properly. Perform regular maintenance on the machine. Secure free-standing shaft ends. WARNING Hot surfaces Electric machines have hot surfaces. Fatal or severe injuries and substantial material damage can occur if the covers are removed or if the machine is not handled, operated, or maintained properly. Allow the machine to cool before starting work on the machine. Only remove the covers using the methods described by these operating instructions. Operate the machine properly. CAUTION Hazardous substances Chemical substances required for the setup, operation and maintenance of machines can present a health risk. Poisoning, skin damage, cauterization of the respiratory tract, and other health damage may result. Read the information in these operating instructions and the product information supplied by the manufacturer. Observe the relevant safety regulations and wear the personal protective equipment specified. CAUTION Flammable substances Chemical substances required for the setup, operation and maintenance of machines may be flammable. Burns and other damage to health and material may result. Read the information in these operating instructions and the product information supplied by the manufacturer. Observe the relevant safety regulations and wear the personal protective equipment specified. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 13 Safety notes 2.4 Working on machines with permanent magnets 2.4 Working on machines with permanent magnets On machines with permanent magnets, the magnetic field is guided in an assembled state in the magnetic circuit of the motor. This means that no magnetic fields, which may be to your health, are detectable outside the machine. WARNING Strong magnetic field when the machine is open A strong magnetic field is always present inside the machine. If the housing is open, e.g. when maintenance openings are open or when working inside the machine, magnetic objects can be suddenly attracted by this magnetic field. This can result in death, severe injury or material damage. Working in the vicinity of the rotor is only permitted in exceptional circumstances. Unambiguous access rules must be established in accordance with the magnetic fields prevailing in the workplace. Clearly mark the boundaries of the areas where standing is permitted. People who need to use electronic or magnetic medical aids such as pacemakers, hearing aids, implants or similar devices, are at particularly high risk. Such persons must undergo an industrial medicine assessment. Observe the following measures. Personal protective measures Ensure that you never wear or carry any of the following objects and that they are kept a safe distance from the machine: - All kinds of magnetic metal parts such as, keys, glasses, tools, knives, scissors, tape measures, etc. - Magnetic jewelry such as rings, chains, needles, watches, etc. - Electronic devices and data carriers such as service cards, check cards, credit cards, calculators, cell phones, etc. - Wallets or other iron-containing objects - Electrically conductive foreign bodies Do not use any magnetic tools or lifting devices. Wear only occupational safety items without magnetic metal parts, e.g. occupational safety shoes with non-magnetic protective caps and soles. Keep your shoes and clothing free from chips and waste containing iron. Exercise caution when installing accessories. Ensure that no parts fall into the inside of the machine. Do not perform any cutting at the machine, e.g. manufacturing threaded holes. Any exceptions require written approval from the manufacturer. 14 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Safety notes 2.5 Electrostatic sensitive devices 2.5 Electrostatic sensitive devices ESD protective measures CAUTION Electrostatic discharge Electronic modules contain components that can be destroyed by electrostatic discharge. These modules can be easily destroyed by improper handling. To protect your equipment against damage, follow the instructions given below. Never touch electronic modules unless absolutely necessary in the course of maintenance and repair procedures. If the modules have to be touched, the body of the person concerned must be electrostatically discharged immediately beforehand and be grounded. Electronic modules should not be brought into contact with electrically insulating materials such as plastic foil, plastic parts, insulating table supports or clothing made of synthetic fibers. Always place electrostatic sensitive devices on conductive bases. Always pack, store and transport electronic modules or components in conductive packaging, e.g. metallized plastic or metal containers, conductive foam material or domestic aluminum foil. The necessary ESD protective measures for electrostatic sensitive devices are illustrated once again in the following drawings: d d b d b e e f c a (1) f f c a f f c (2) a (3) (1) Sitting (2) Standing (3) Standing/sitting a = conductive floor surface b = ESD table c = ESD shoes d = ESD overall e = ESD wristband f = cabinet ground connection See also Replacing the DRIVE-CLiQ interface (encoder module) (Page 63) A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 15 Safety notes 2.6 Electromagnetic compatibility (EMC) 2.6 Electromagnetic compatibility (EMC) This machine is designed in accordance with IEC / EN 60034 and when used as prescribed it satisfies the requirements of European Directive 2004/108/EC on Electromagnetic Compatibility. 2.6.1 Interference immunity The machine fulfills the requirements regarding interference immunity in conformity with IEC / EN 61000-6-2. When using machines with integrated sensors (PT100, PTC thermistors), the manufacturer of the overall plant must himself ensure sufficient interference immunity by selecting suitable sensor signal leads and evaluation units. 2.6.2 Emitted interference WARNING Interference on electronic devices through electromagnetic fields Electromagnetic fields are generated by the operation of electrical power engineering installations such as motors, converters or transformers. Electromagnetic fields can interfere with electronic devices, resulting in malfunctioning of those devices. The operation of heart pacemakers can be impaired, potentially leading to damage to a person's health or even death. It is therefore forbidden for persons with heart pacemakers to come into the vicinity of the machine. Data may be lost from magnetic or electronic data media. Ensure that the personnel working in these areas are adequately protected from any harm by making appropriate arrangements, such as erecting identifying markings, safety barriers and warning signs and giving safety talks. Observe the nationally applicable health and safety regulations. Do not carry any magnetic or electronic data media with you. 16 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 3 Description 3.1 Applications Three-phase motors of the 1PH8. series are used as industrial drives. They have been designed for a wide range of applications in the fields of drive engineering and power conversion. They are characterized by their high power density, ruggedness, long lifetime, and overall reliability. 3.2 Rating plate The machine rating plate shows the technical specifications applicable to the supplied motor. Figure 3-1 Schematic layout of rating plate Table 3-1 Elements on the rating plate No. Description No. Description 010 MLFB 170 Rated speed nN (2) 012 Consecutive number, part of serial number 180 Operating mode (2) 020 Serial number 185 Code for operating point 2 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 17 Description 3.3 Layout No. Description No. Description 025 UL approval 190 Rated voltage VN (3) 026 (Empty) 191 Switching mode 3 030 Type of construction 200 Rated current IN (3) 035 (Empty) 210 Rated power PN (3) 036 (Empty) 220 Induced voltage UI [V] (3) 040 Degree of protection 230 Rated frequency fN (3) 045 Type of balancing 240 Rated speed nN (3) 049 Induced voltage at rated speed UIN 250 Operating mode (3) 050 Rated voltage VN (1) 255 Code for operating point 3 051 Switching mode 1 270 Maximum current IMAX 060 Rated current IN (1) 275 Maximum torque MMAX 070 Rated power PN (1) 280 Maximum speed nMAX 080 Induced voltage UI [V] (1) 285 Temperature sensor 090 Rated frequency fN (1) 290 Tachometer/resolver 100 Rated speed nN (1) 295 Cooling method 110 Operating mode (1) 296 Throughput l/min (m3/s) 115 Code for operating point 1 297 System pressure 120 Rated voltage VN (2) 298 Maximum coolant temperature 121 Switching mode 2 315 Options (I) 130 Rated current IN (2) 320 Options (II) 140 Rated power PN (2) 325 Optional customer information 150 Induced voltage UI [V] (2) 330 Anti-condensation heater / place holder 160 Rated frequency fN (2) 335 Weight 3.3 Layout Rotor This machine is a synchronous motor for low voltage with the permanent magnet rotor and integrated cooling circuit. Machine design The regulations and standards underlying the design and testing of this machine are stated on the rating plate. The machine design basically complies with the following standards: Table 3-2 18 Machine design Feature Standard Ratings and operating performance IEC / EN 60034-1 Degree of protection IEC / EN 60034-5 Cooling IEC / EN 60034-6 Type of construction IEC / EN 60034-7 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Description 3.3 Layout Feature Standard Noise emission IEC / EN 60034-9 Vibration severity grades IEC / EN 60034-14 Drive The speed of the machine is controlled by a frequency converter. Types of construction The motor is available in the following basic types of construction and further optional types of construction with additional application possibilities. Table 3-3 Types of construction Basic types of construction Other applications in construction type IM B3 IM B6, IM B7, IM B8, IM V6 IM V15 - IM V5 - IM B35 IM B5, IM V3, IM V35 The machine is supplied with two assembled lifting eyes. For IM V5 and IM V15 types of construction with "shaft extension pointing downward", the machine is equipped with two additional Vario eye bolts. Cooling circuit The cooling circuit consists of high-grade steel tubes that are directly integrated into the laminated stator core. The machine is in an enclosed design which incorporates a cooling circuit, cooling method IC 37W in accordance with IEC / EN 60034-6. Cooling capacity To ensure adequate cooling of the motor, it is essential to adhere to the specified cooling water rate and cooling water quality (Page 33). Degree of protection The machine is available with degree of protection IP55. Supplementary devices A KTY 84 temperature sensor is installed (Page 40) in the stator winding for winding control. Depending on the order options, various supplementary devices such as encoder systems can be either installed or mounted. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 19 Description 3.3 Layout Ambient conditions The standard machines are not suitable for use in corrosive atmospheres, atmospheres with a high salt content, or outdoor applications. Bearings The machines are equipped with different types of roller bearings depending on the version and the operating conditions described in the order. If the machine is equipped with a regreasing system, you will find the relevant data on the machine's lubricant plate. The following roller bearing versions are available: Table 3-4 Roller bearing versions Design Bearings Standard design Drive end deep-groove ball bearing as spring-loaded floating bearing Bearing design for increased transverse forces Drive end cylindrical-roller bearing as floating bearing Non-drive end deep-groove ball bearing as fixed bearing Non-drive end deep-groove ball bearing as fixed bearing CAUTION Permissible loads Exceeding the permissible loads for the forces at the shaft extension can cause damage to the bearing and the machine. Not meeting the minimum transverse forces on cylindricalroller bearings can also result in damage. Keep to the permissible loads in accordance with the catalog data. 20 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Preparations for use 4.1 Shipment and packaging 4.1.1 Scope of supply 4 Checking the delivery for completeness The drive systems are put together on an individual basis. When you take receipt of the delivery, please check immediately whether the items delivered are in accordance with the accompanying documents. Siemens will not accept any claims relating to items missing from the delivery and which are submitted at a later date. Report any apparent transport damage to the delivery agent immediately. Report any apparent defects/missing components to the appropriate Siemens office immediately. These safety instructions are part of the scope of supply; keep them in a location where they can be easily accessed. 4.2 Transport and storage 4.2.1 Transporting Damage during transportation Notify the shipping company immediately if you have found any damage to the motor after delivery. Never commission a damaged motor. Transporting Please comply with the following instructions for transporting the motor. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 21 Preparations for use 4.2 Transport and storage WARNING Always transport and lift the motor on the lifting eyebolts If you lift the motor by the cooling water pipe system, the pipes will be damaged and the motor might be dropped. Death, serious injury, or material damage to the motor - even a write-off - can result. Do not attach the motor at the cooling water pipes when you have removed the bearing end shields. The bearing end shields must always be mounted when you transport the motor. There are two lifting eyebolts for horizontal transport of the motor. In addition there are two threads for vertical lifting with the shaft end pointing downwards. For this, the lifting eyebolts and the threaded plugs have to be swapped around. Only lift the motor at the lifting eyebolts on the bearing end shields. To hoist the motor, in particular if there are built-on assemblies, use suitable cable-guidance or spreading equipment. Pay attention to the lifting capacity of the hoisting gear. The weight of the motor is specified on the rating plate (Page 17). 22 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Preparations for use 4.2 Transport and storage Figure 4-1 Lifting the machine Rotor shipping brace Machines ordered with the "Increased transverse force" option are equipped with cylindricalroller bearings and a rotor shipping brace. CAUTION Transport damage if the rotor shipping brace device is not used. The motor can be damaged if it is jolted during transport. Material damage can result. Always transport the motor with the rotor shipping brace supplied. It must be securely attached during transportation. Only remove it before pushing on the drive element. When the motor has to be transported after the drive element is pushed on you must take other appropriate measures to fix the axial position of the rotor. Please refer to the illustration below. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 23 Preparations for use 4.2 Transport and storage Sleeve Shaft screw Figure 4-2 Rotor shipping brace Table 4-1 Tightening torque for rotor shipping brace Type Thread in the shaft end Tightening torque Preload 1PH818. M20 50 Nm 12 kN 1PH822. M20 50 Nm 12 kN Transporting a motor that has been in operation If you have already operated the motor and now want to transport it, proceed as follows: 1. Allow the motor to cool down. 2. Remove the connections provided by the customer. 3. Drain the cooling-water system and purge it carefully with air. 4. Fit the rotor shipping brace. 5. Always use only the lifting eyebolts on the bearing end shields to transport and lift the motor. 4.2.2 Storage The motors can be stored for up to two years in dry, dust-free and vibration-free rooms without reducing the specified storage time. CAUTION Seizure damage to bearings If the motors are stored incorrectly there is a risk of bearing seizure damage such as brinelling, for example as a result of vibrations. Read the following storage instructions. 24 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Preparations for use 4.2 Transport and storage Preparation Fit the rotor shipping brace. Apply a preserving agent such as Tectyl to bare external components such as shaft ends, if this has not already been applied in the factory. Storing indoors CAUTION Damage caused as a result of outdoor storage Storing the machine outdoors can result in it being damaged. Ensure that the machine is only stored in areas that comply with the following conditions. Store the motor in an area that meets the following criteria: - Dry, dust-free, frost-free and vibration-free The relative air humidity should be lower than 60% and the temperature should not drop below -15 C in accordance with EN 60034-1. - Well ventilated - Offers protection against extreme weather conditions - The air in the storage area must not contain any harmful gases. Protect the motor from shocks and humidity. Cover the motor properly. Avoid contact corrosion: - Every three months, remove the shipping brace and rotate the shaft end by hand. - Then reattach the rotor shipping brace. Protection against humidity If a dry storage area is not available, then take the following precautions: - Wrap the motor in humidity-absorbent material and then wrap it in film to create an airtight unit. - Include several bags of desiccant in the seal-tight packaging. Check the desiccant and replace as required. - Place a humidity meter in the seal-tight packaging to indicate the level of air humidity inside it. - Inspect the motor regularly. Long-term storage If you are storing a machine for more than six months, you must check its condition every six months. Check the machine for damage. Carry out any necessary maintenance work. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 25 Preparations for use 4.2 Transport and storage Document all preservation measures taken so that they can be reversed before the machines are put back into service. Provide air-conditioning for the storage room. Condensation Condensation can collect in the machine as a result of sharp fluctuations in ambient temperature, exposure to direct sunlight, high levels of humidity in the storage location or intermittent operation/variations in load during operation. CAUTION Damage caused by condensation If the stator winding is damp, its insulation resistance is reduced. This results in voltage flashovers, which can destroy the winding. Condensation can also cause rusting inside the machine. In the bearing shields at the DE and NDE, water drain holes are situated in the foot area and opposite the regreasing system. Make sure that the condensation can always drain away freely. The plug that has been inserted into the water drain holes allows the condensation to drain away. Do not remove the plug, otherwise the machine's degree of protection will be affected. Note In IM B3, IM B5, IM B35 types of construction, water drainage holes are only functional in horizontal installations. 4.2.3 Protecting the cooling-water system When the units are delivered, the high-grade steel cooling-water pipe system is not filled with cooling water. When you put the motor into storage after use, drain the cooling water ducts and purge with air to ensure that they are completely empty. For operation, add a maximum of 20 % to 30 % of an anti-freeze agent to the cooling water; use Antrifrogen N or Tyfocor, for example, as the anti-freeze. CAUTION Frost damage to the cooling circuit Damage may be caused to the cooling circuit if the cooling water freezes. If the ambient temperature falls below 0 C during operation add anti-freeze to the cooling water. 26 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 5 Assembling 5.1 Heat-resistant mounting parts CAUTION Heat-resistant mounting parts The motor components get very hot during operation. High temperatures can damage mounting parts such as the cable insulation. Temperature-sensitive parts such as normal cables or electronic components must not rest against or be attached to these. Only use heat-resistant mounting parts. The connecting cables and cable entries must be suitable for the ambient temperature. Note the technical data provided in this documentation and on the plates on the motor frame. 5.2 Installing The following points must be taken into account when installing the machine: The conditions of the IP degree of protection must be observed. The assemblies and pipework must be mounted free of stress. Noise emissions The motors are certified for a wide range of installation and operating conditions. These conditions such as rigid or vibration-isolated foundation design influence noise emission, sometimes significantly. Table 5-1 Noise emissions Design Measuring-surface sound-pressure level Lp(A) Rated pulse frequency 1PH818. 70 [dB(A)] + 3 dB tolerance 2 kHz / 4 kHz 1PH822. 70 [dB(A)] + 3 dB tolerance 2 kHz / 4 kHz No-load operation at SINAMICS S120; measurement: enveloping surface method in accordance with DIN 45635-1 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 27 Assembling 5.3 Alignment preconditions 5.3 Alignment preconditions Prerequisites Detailed specialist knowledge of the following measures is required in order to correctly align and securely fit the equipment. Preparing the foundation Selecting and mounting the coupling Measuring the concentricity and axial eccentricity tolerances Positioning If you are not familiar with the prescribed measures and procedures, then you can make use of the services offered by the local Siemens Service Center. 5.4 Aligning the machine with the driven load Vertical and horizontal alignment The following measures are required in order to compensate any radial offset at the coupling and to horizontally adjust the electric motor with respect to the driven load: Place shims under the motor feet to position it vertically and to prevent stress/distortion. The number of shims should be kept as low as possible, so use as few thicker shims as possible, instead of several thinner shims. For horizontal positioning, push the motor sideways on the foundation Pay attention to maintaining the axial position. When positioning the motor, ensure that a uniform axial gap is maintained around the coupling. 28 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Assembling 5.5 Securing the machine Alignment accuracy 1. Align the motors with coupling output in such a manner that the center lines of the shafts are parallel with no offset. This ensures that no additional forces affect their bearings during operation. 2. Perform the fine adjustments with plates under the entire motor foot. KR H K Figure 5-1 Table 5-2 5.5 K KKR Aligning the machine Permissible deviations when aligning the motor Permissible deviations Radial shaft offset [e] Axial shaft offset [h] Flexible coupling 0,05 mm 0,05 mm Securing the machine Preconditions for smooth, vibration-free operation Foundation design as per DIN 4024 Precise alignment of the machine Correct balancing of parts to be fitted to the shaft extension. ISO 10816-3-compliant vibration speeds. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 29 Assembling 5.6 Pushing on the power output elements Fixing by means of motor feet The contact surfaces of the motor feet must lie on one plane. If the motor needs to be aligned, position metal shims underneath the feet in order to prevent machine deformation. The number of shims should be kept as low as possible i.e. stack as few as possible. Select foot screws as per ISO 898-1 in compliance with the load conditions and machine type: Type Foot screw size 1PH818. M12 1PH822. M16 Fixing by means of flange only The flange is only used to transfer the torque. Due to the empty weight or as a result of vibrations that arise if the flange is too soft, the motor can be damaged if it is only fastened via the flange. 1. Fasten the flange motors via a stable motor suspension and support them via the end shield feet (foot flange type of construction). 2. During commissioning, ensure that the permitted vibration values are maintained in accordance with ISO 10816-3. If the machine is only to be secured via the flange, with a rigid base the maximum speed is lowered as follows: - Max. 3000 1/min for 1PH818. - Max. 2500 1/min for 1PH822. 5.6 Pushing on the power output elements Balance quality The rotors are balanced dynamically. For shaft extensions with featherkeys, the balancing type is specified using the following coding on the face of the drive end of the shaft: "H" means balancing with a half feather key "F" means balancing with a whole feather key. 30 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Assembling 5.7 Condensation drain holes Pushing on the power output elements Make sure that the balancing method of the output element is correct! If the power output element is shorter than the feather key with balancing type "H", then you must machine off the section of feather key protruding from the shaft contour and output element in order to maintain the balance quality. Power output elements may only be pushed on or pulled off with the correct equipment. WARNING The feather key can fall out The featherkeys are only secured during transport to prevent them from falling out. If a machine with two shaft extensions does not have an output element on one shaft extension, the feather key can fall out during operation. Death or serious injury can result. On shaft extensions without output element, make sure that the feather key cannot fall out and shorten it by approximately half for balance type "H". 5.7 Condensation drain holes In the bearing shields at the DE and NDE, a water drain hole is situated in the foot area and another opposite the regreasing device. 1 Figure 5-2 Water drain holes A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 31 Assembling 5.7 Condensation drain holes Make sure that the condensation can always drain away freely. The plug that has been inserted into the water drain holes allows the condensation to drain away. Do not remove the plug, otherwise the machine's degree of protection will be affected. If you have any questions, contact the Siemens Service Center. CAUTION Damage caused by condensation If the stator winding is damp, its insulation resistance is reduced. This results in voltage flashovers, which can destroy the winding. Condensation can also cause rusting inside the machine. Make sure that the condensation can always drain away freely. 32 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 6 Connection 6.1 Mechanical connection 6.1.1 Cooling water quality The values specified for the cooling water correspond to the requirements for a closed cooling circuit. Not all of the specified concentrations will occur in the cooling water at the same time. A filter can be used to ensure smooth operation; the grade of filtration should not exceed 100 m. Cooling water inlet temperature The maximum cooling water inlet temperature is 30 C. Cooling water specification Table 6-1 Cooling water specification Constituent Value pH value 6,0 ... 9,0 Total hardness < 170 ppm Conductivity < 500 S/cm Chloride ions < 40 ppm Sulfate ions < 50 ppm Nitrate ions < 50 ppm Dissolved solids < 340 ppm Max. grain size < 100 m Operating pressure Max. 6 bar Inlet temperature < 30 C Minimum inlet temperature of the cooling water Tcooling water > Tambient - 5 K Anti-freeze protection / corrosion protection 20 ... 30 % Inhibitor NALCO 00GE056 0,2 ... 0,25 % A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 33 Connection 6.1 Mechanical connection NOTICE Inlet temperature of the cooling water If the minimum inlet temperature of the cooling water cannot be maintained or reached, this may result in condensation forming on the machine. Adopt appropriate measures to achieve the inlet temperature of the cooling water. Alternatively, you can dry the ambient air. 6.1.2 Connecting the cooling water supply The inlet and outlet sockets for the cooling water supply are situated on the non-drive end in the bearing shield area. On the bearing shield, there are two hexagonal couplers with a female thread, which are each screwed onto a washer: At shaft heights of 180 and 225, hexagonal couplers with 3/8" female threads are used. 1. Only use valves, fittings and cooling water pipes made of non-corrosive, high-grade steel in the cooling system. 2. Make sure that the cooling water meets the required cooling water specification, see section headed "Cooling Water Quality" (Page 33). 3. Make sure that the appropriate volume of cooling water is available, see Rating Plate (Page 17). 4. Hold the hexagon head steady with an open-ended spanner while you screw in the water pipes. 5. Screw the cooling water pipes into the female thread. You can connect the inlet and outlet as required. NOTICE Securing the hexagonal couplers The hexagonal couples are connected directly to the water pipes inside the machine. The application of excessive torque during screwing in can damage the pipe system. Hold the couplers steady with an open-ended spanner when you screw in the water pipes. 6. Ensure that the maximum permissible operating pressure does not exceed 6 bar. The pressure drop is determined by the machine type and the shaft height: Table 6-2 Type 34 Rate of flow and pressure drop Flow rate Pressure drop 1PH8 184 15 l/min 0.6 bar 1PH8 186 15 l/min 0.7 bar 1PH8 224 25 l/min 0.9 bar A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Connection 6.2 Electrical connection Type 6.2 Flow rate Pressure drop 1PH8 226 25 l/min 0.9 bar 1PH8 228 25 l/min 0.9 bar Electrical connection Observe the general safety instructions (Page 11) for all work on the machine. 6.2.1 Safety note for the DRIVE-CLiQ interface CAUTION Electrostatically sensitive devices The DRIVE-CLiQ interface contains components that are susceptible to electrostatic charging. Touching connections with electrostatically charged hands or tools can cause malfunctions. Maintain the ESD protective measures (Page 15) as well as the five safety rules (Page 11). 6.2.2 Cable entry and routing When selecting the connecting cables, you must take into account the rated current and the plant-specific conditions (e.g. ambient temperature, routing type etc. in accordance with IEC / EN 60364-5-52). Use EMC cable glands for permanently installed entry fittings. Screw the EMC cable glands into the threaded holes in the entry plate, which can be unscrewed. Use shielded cables whose shields are conductively connected to a large area of the terminal box of the motor via EMC cable glands. Arrange the exposed connecting cables in the terminal box so that the PE conductor has excess length and the insulation of the cable strands cannot be damaged. NOTICE Close off unused bushings with a metal threaded plug. This is the way to achieve a high frequency-proof shielding. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 35 Connection 6.2 Electrical connection 6.2.3 Electrical connection data Connection table Cable entry and technical connection data depend on the mounted terminal box: 1XB7 322 1XB7 422 1XB7 700 36 1XB7 712 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Connection 6.2 Electrical connection Table 6-3 Electrical connection data Terminal box type Cable entry Max. poss. cable outer diameter Number of main terminals Max. cross-section per terminal Current per terminal (max.) 1XB7 322 2 x M50 x 1,5 38 mm 3 x M12 2 x 50 mm2 210 A 1XB7 422 2 x M63 x 1,5 53 mm 3 x M12 2 x 70 mm2 270 A 3 x 150 mm2 700 A 4 x 185 mm2 1150 A 1XB7 700 1XB7 712 3 x M75 x 1,5 68 mm 4 x M75 x 1,5 68 mm 3 x 2 x M12 3 x 4 x M16 Current carrying capacity based on IEC / EN 60204-1or IEC / EN 60364-5-32 6.2.4 Terminal designation The following definitions apply to the terminal designations of three-phase machines in accordance with DIN VDE 0530 Part 8 or IEC / EN 60034-8: Table 6-4 1 U Terminal designations using the 1U1-1 as an example 1 - 1 Designation x Index for pole assignment on pole-changing motors where applicable. A lower index signifies a lower speed. Special case for split winding. x Phase designation U, V, W x Index for winding start (1) or end (2) or if there is more than one connection per winding x 6.2.5 Additional index for cases in which it is obligatory to connect parallel power feed cables to several terminals with otherwise identical designations Connection with cable lugs To connect the cables to the main terminals, select cable lugs that match the necessary cable cross-section and appropriate screw size. The connectable cable cross section is determined by the cable lug size for example. - Cable lug in accordance with DIN 46234, from 35 mm2 to 185 mm2, - Cable lug in accordance with DIN 46235, from 35 mm2 to 185 mm2. Observe the possible outer diameter of the connecting cable in the chapter entitled "Electrical connection data". Remove the insulation from the conductor ends so that the remaining insulation is almost long enough to reach the cable lug. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 37 Connection 6.2 Electrical connection If necessary, insulate the cable lug sleeves in order to maintain the minimum clearances in air of 10 mm and the 20 mm creepage distance normally present. The tightening torque for contact nuts and fixing screws depends on the size of the screw: Screw size Tightening torque for contact nuts and fixing screws M12 40 Nm M16 90 Nm 1P Figure 6-1 Connection using cable lugs See also Electrical connection data (Page 36) 6.2.6 Connect up the ground conductor General The grounding conductor of the motor must be in full conformance with the installation regulations, e.g. in accordance with IEC/EN 60204-1. 38 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Connection 6.2 Electrical connection Connecting the grounding conductor Connect the ground conductor to the end shield of the motor. There is a fixing lug for the ground conductor at the designated connection point. - The fixing lug is suitable for grounding high-frequency currents using HF ribbon cable with appropriately formed conductor ends. Figure 6-2 Detailed view: Connection point for ground conductor When making connections, ensure the following: - the connecting surface is bare and protected against corrosion using a suitable substance, e.g. acid-free Vaseline - the flat and spring washers are located under the bolt head. 6.2.7 Internal equipotential bonding The internal equipotential bonding between the grounding terminal in the box enclosure and the motor frame is established through the terminal box retaining bolts. The contact locations underneath the bolt heads are bare metal and protected against corrosion. The standard cover fixing screws are sufficient for equipotential bonding between the terminal box cover and terminal box housing. Note Connecting points are provided on the enclosure or end shield to allow an outer PE conductor or equipotential bonding conductor to be connected; see section entitled "Connecting the ground conductor". 6.2.8 Circuit diagram Information concerning wiring and connecting the motor winding is specified in the circuit diagram. The circuit diagram is attached to the lid of the terminal box. Cable selection When selecting the connecting cables, you must take into account the rated dynamic current and the plant-specific conditions e.g. ambient temperature, routing type etc. in accordance with IEC / EN 60204-1. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 39 Connection 6.2 Electrical connection 6.2.9 Connecting the speed encoder Connect the speed sensor to the terminal box by means of a plug-in connection . This is located on the terminal box enclosure. Figure 6-3 Detailed view: Plug-in connection Note The plug-in connection may differ from the standard layout in the case of special orders. In the version without a speed sensor, an armored conduit union is located here. 6.2.10 Connecting the temperature sensor The temperature sensor is connected to the signal connector together with the speed sensor signal. In the version without a speed sensor, connect the signal lines for the temperature sensor to the auxiliary terminal strip in the terminal box. The circuit diagram is located in the cover of the terminal box. The motor has a reserve temperature sensor which is also placed on the auxiliary temperature strip. Clamp the temperature sensor as needed e.g. if the former temperature sensor fails. 40 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Connection 6.2 Electrical connection 6.2.11 Connection to a converter Selecting and connecting the cable Use Motion Connect cables or symmetrically constructed, shielded cables to connect the motor to a converter. The cable shielding, made up of as many strands as possible, must have good electrical conductivity. Braided shields made of copper or aluminum are well suited. The shield must be connected at both ends to the motor and the converter; unshielded cable ends must be kept as short as possible. To ensure effective discharge of high-frequency currents, make the shield contact over the largest possible area, i.e. as a 360 contact on the converter and motor, e.g. using EMC glands at the cable entry points. Measures to reduce bearing currents To specifically reduce and prevent damage caused by bearing currents, you must consider the system as a whole, which comprises the motor, converter, and driven machine. The following precautions help to prevent bearing currents: Setting up a properly meshed grounding system in the system as a whole, with low impedance for high-frequency currents No potential difference between the motor, converter, and working machine. - Use symmetrical, shielded connecting cables. - Connect the cable shield at both ends over the greatest possible surface area (360 contact). - Use equipotential bonding conductors between the motor and driven machine, motor and converter and inside the motor Use iron cores mounted above the motor connecting cable at the converter output. These help to reduce common-mode components. The Siemens sales representative is responsible for selection and dimensioning. Limit the voltage rate of rise by using an output filter to dampen harmonic components in the output voltage 6.2.12 Converter operation on a grounded network Parallel PE conductor In the case of current-limited converters without ground fault monitoring, PE conductor currents of up to 1.7 times the external conductor current can arise if there is a ground fault on the output side. Neither the PE conductors of normally rated multi-core connecting cables nor the PE connecting points of normal terminal boxes are suitable for this purpose. Use an appropriately sized parallel PE conductor. Connect the parallel PE conductor to the grounding terminal on the motor enclosure. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 41 Connection 6.2 Electrical connection 6.2.13 Final steps 1. Before closing the terminal box, please check that: - the electrical connections in the terminal box are tight and are in full compliance with the specifications above. - the required clearances in air of 10 mm are maintained. - no wire ends are protruding. - the inside of the terminal box is clean and free of any cable debris. - all seals and sealing surfaces are undamaged. - the connecting cables are arranged so that they do not come into contact with the machine, and the cable insulation cannot be damaged. - unused entry points are sealed. The sealing elements are firmly screwed in, i.e. they can only be removed with a tool. - the right cable glands are fitted with respect to the correct degree of protection, method of laying, permissible cable diameter etc., as stated in the specifications. 2. Then close the terminal box with the terminal box cover fixing screws, with the following tightening torques. Table 6-5 42 Tightening torque for the terminal box cover fixing screws Terminal box type Screw Tightening torque 1XB7 322 M6 4.5 Nm 1XB7 422 M8 11 Nm 1XB7 700 M10 22 Nm 1XB7 712 M8 11 Nm A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Commissioning 7 Observe the general safety instructions (Page 11) for all work on the machine. WARNING Driving the motor via the system During a short circuit of a cable or converter, a short-circuit current is driven by the induced voltage which is present at the motor terminals due to the rotation of the permanent magnet rotors. The motor can rotate unexpectedly at any time, which can result in death, serious injury, or material damage. If it is possible for the motor to be passively driven during system operation, ensure that short-circuit-resistant cables are used. Optionally, you can use circuit breakers near the motor for protecting the sections of cable during a short circuit. WARNING Dangerous voltage at the motor terminals when the rotor is rotating There is always a magnetic flux in the motor due to the permanent magnets in the rotor. With each rotation of the rotor, a voltage occurs at the motor terminals. As a result of this, there is also a voltage at the converter output terminals via the connecting cable. Contact with them can cause death, serious injury or material damage. When working on the drive system, you must prevent any rotational movement of the motor shaft. WARNING Dangerous voltage via the converter As long as the feeding converter is switched on, or the DC link of the converter is not discharged, there can be a voltage at the motor terminals even when the rotor is not moving. Contact with them can cause death, serious injury or material damage. The voltage is up to 1000 V, depending on the converter type. Maintain the five safety rules (Page 11)at all times when operating the machine. 7.1 Measures to be performed prior to commissioning Before commissioning the system, check that it is properly installed and connected. It may be necessary to perform additional checks and tests in accordance with the situation specific to the particular place of installation. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 43 Commissioning 7.1 Measures to be performed prior to commissioning Mechanical connection All touch protection measures for moving and live parts have been taken. The motor has been assembled and aligned properly. The operating conditions correspond to the data specified on the rating plate. The grounding and equipotential bonding connections have been established correctly. All fixing screws, connecting elements and electrical connections are firmly tightened. if the second shaft end has not been used, its feather key has been secured to prevent it from being thrown out. The power output elements have the proper setting conditions according to type, for example. - Couplings are aligned and balanced. - The belt tension is properly adjusted if there is a belt drive. - Gear tooth flank play and gear tooth tip play as well as radial play are properly adjusted if there is gearwheel drive. Electrical connection The motor is connected so that it rotates in the direction specified. The minimum insulation resistance values are maintained. All brakes are operating correctly. The indicated speed limit nmax is not exceeded during operation on a converter. Monitoring equipment Appropriately configured control and speed monitoring functions ensure that the motor cannot exceed the permissible speeds specified on the rating plate. Any supplementary motor monitoring devices and equipment have been correctly connected and are fully functional. Cooling The cooling water supply is connected and ready for operation. Rolling-contact bearings If the motor has been stored for more than three years in a dry, dust-free and vibration-free room, prepare the commissioning procedure as follows: Replace the bearings on motors with lifetime lubrication. Replace the grease in motors with re-greasing system. If stored under less favorable conditions, replacement of bearings or re-greasing must be carried out after a storage period of approx. 18 months. 44 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Commissioning 7.2 Trial run 7.2 Trial run If you want to start the motor for a trial run, connect it to the cooling water supply. WARNING Risk of burning from hot steam If the cooling water supply fails, the motor will overheat. If cooling water runs into the hot motor, hot steam suddenly forms, which escapes under high pressure. The cooling water system can burst. This can result in death, serious injury or material damage. Do not connect the cooling water supply until the motor has cooled down. 7.3 Checking insulation resistance Safety note WARNING Only expert personnel should be entrusted with work on power installations. Checking the insulation resistance After long storage or shutdown periods, the insulation resistance of the windings must be measured to ground with direct voltage. CAUTION Before you begin measuring the insulation resistance, please read the manual for the insulation resistance meter you are going to use. WARNING Hazardous voltage During the measurement, and immediately afterwards, hazardous voltage levels are applied on some of the terminals and they should not be touched. Touching live components can be result in death or serious injury. Never touch the terminals when measuring or immediately after the measurement. Check the supply feeder cables connected in order to ensure that the line supply voltage cannot be connected. Always measure the insulation resistance of the winding to the motor enclosure when the winding temperature is between 20 and 30C. When measuring, wait until the final resistance value is reached; this takes approximately one minute. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 45 Commissioning 7.3 Checking insulation resistance Limit values The table below specifies the measuring circuit voltage as well as the limit values for the minimum insulation resistance and the critical insulation resistance with a rated motor voltage of UN < 2 kV: Table 7-1 Stator winding insulation resistance at 25 C Rated voltage UN < 2 kV Measuring circuit voltage 500 V (at least 100 V) Minimum insulation resistance with new, cleaned or repaired windings 10 M Critical specific insulation resistance after a long operating time 5 M/kV Note the following: Dry, new windings have insulation resistance of between 100 and 2000 M, or possibly values that are even higher. If the insulation resistance is close to the minimum value, then the cause could be humidity and/or fouling. Over its operating lifetime, the motor winding insulation resistance can drop due to ambient and operational influences. The critical insulation resistance for a temperature of 25C on the winding can be calculated by multiplying the rated voltage (kV) by the specific critical resistance value (5 M/kV); Example: Critical resistance for a rated voltage (UN) of 500 V: 500 V x 5 M/kV = 2.5 M NOTICE Cleaning and/or drying the windings when reaching critical insulation resistance If the critical insulation resistance is less than or equal to this value, the windings must be dried or, if the fan is removed, cleaned thoroughly and dried. Note that the insulation resistance of dried, clean windings is lower than that of warm windings. The insulation resistance can only be evaluated accurately when measured on a winding that has been cooled down to room temperature (approx. 20 to 30C). NOTICE Measured value close to critical value If the measured value is close to the critical value, the insulation resistance should be subsequently checked at appropriately frequent intervals. Values apply for measurement at a winding temperature of 25 C. 46 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Commissioning 7.4 Switching on 7.4 Switching on Before you switch on the motor, ensure that the parameters of the frequency converter have been assigned correctly. Use appropriate commissioning tools, such as "Drive ES" or "STARTER". CAUTION Operation noise or abnormal noises The motor can be damaged by improper handling during transport, storage or set up. If a damaged motor is operated damage to the winding, bearings or, complete destruction of the motor can be the result. If the motor is not running smoothly or is emitting abnormal noises, de-energize it, and determine the cause of the fault as the motor runs down. NOTICE Pay attention to the maximum rotational speed The maximum rotational speed nmax is the highest permissible operating speed. The maximum rotational speed is specified on the rating plate. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 47 Commissioning 7.4 Switching on 48 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 8 Operation Observe the general safety instructions (Page 11) for all work on the machine. WARNING Dangerous voltage at the motor terminals when the rotor is rotating There is always a magnetic flux in the motor due to the permanent magnets in the rotor. With each rotation of the rotor, a voltage occurs at the motor terminals. As a result of this, there is also a voltage at the converter output terminals via the connecting cable. Contact with them can cause death, serious injury or material damage. When working on the drive system, you must prevent any rotational movement of the motor shaft. WARNING Dangerous voltage via the converter As long as the feeding converter is switched on, or the DC link of the converter is not discharged, there can be a voltage at the motor terminals even when the rotor is not moving. Contact with them can cause death, serious injury or material damage. The voltage is up to 1000 V, depending on the converter type. Maintain the five safety rules (Page 11)at all times when operating the machine. 8.1 Safety notes during operation WARNING Do not remove covers when the motor is running Rotating or live parts are dangerous. Death, serious injury, or material damage can result if the required covers are removed. All covers that are designed to prevent active or rotating parts from being touched, ensure compliance with a particular degree of protection, or that are required for ensuring proper air guidance and, in turn, effective cooling must not be opened during operation. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 49 Operation 8.2 Do not operate without cooling water supply WARNING Faults in operation Deviations from normal operation such as increased power consumption, temperatures or vibrations, unusual noises or odors, tripping of monitoring devices, etc., indicate that the machine is not functioning properly. This can cause faults which can result in eventual or immediate death, serious injury, or material damage. Immediately inform the maintenance personnel. If you are in doubt, immediately switch off the motor, being sure to observe the systemspecific safety conditions! CAUTION Risk of corrosion due to condensation During motor operation, humid air can condense inside the machine. Condensation can collect inside the machine. Damage such as rust can result. The motor is equipped with condensation drain holes. Make sure that the condensation can drain away freely. 8.2 Do not operate without cooling water supply The motor must always be connected to the cooling water supply during operation. CAUTION Cooling water supply If the cooling water supply fails or if the motor is operated for a short time without water cooling, the motor will overheat. This can result in material damage or even a write-off. Never operate the motor without the cooling water supply switched on. Monitor the permissible water inlet temperatures. WARNING Risk of burning from hot steam If the cooling water supply fails, the motor will overheat. If cooling water runs into the hot motor, hot steam suddenly forms, which escapes under high pressure. The cooling water system can burst. This can result in death, serious injury or material damage. Do not connect the cooling water supply until the motor has cooled down. 50 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Operation 8.3 Stoppages 8.3 Stoppages Measures when motors are at standstill and ready for operation For longer periods when the motor is not being used, either energize the motor at regular intervals (roughly once a month), or at least spin the rotor. Please refer to the "Switch on" (Page 47) section before recommissioning the motor. NOTICE Damage due to improper storage The motor can be damaged if it is not stored properly. If the motor is out of service for extended periods of time, implement suitable anticorrosion, preservation, and drying measures. When recommissioning the motor after a long period out of service, carry out the measures recommended in the chapter entitled "Commissioning (Page 43)". 8.4 Switching off When switching off, pay attention to the operating instructions of the frequency converter. Switch off the cooling water supply if the standstill period is expected to be lengthy. 8.5 Faults 8.5.1 Electrical faults Note When operating the machine with a converter, please also refer to the operating instructions of the frequency converter if electrical faults occur. NOTICE Damage to the machine caused by faults Correct the cause of the fault as specified in the remedial measures section. Repair any damage to the machine. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 51 Operation 8.5 Faults Table 8-1 Electrical faults Motor fails to start Motor accelerates reluctantly Rumbling noise during start-up Rumbling noise during operation Overheating during no-load operation Overheating with load Overheating of individual winding sections X X X X X Possible causes of faults Remedial measures Overload Reduce the load. Interruption of a phase in the supply cable Check frequency converters and supply cables. X X X X X X X X X X X Interruption of a phase in the supply after switching on Check frequency converters and supply cables. Converter output voltage too high, frequency too low Check the setting at the frequency converter and perform the automatic motor identification. Winding short circuit or phase short circuit Determine the winding and insulation in stator winding resistances. Carry out repair work after consultation with manufacturer. Cooling water not connected Cooling water supply switched off X 52 X Check the cooling water connection. Switch on the cooling water supply. Water connection / pipes defective Locate the non-watertight section and seal it or consult the manufacturer. Cooling water flow rate too low Increase the cooling water flow rate. Upstream temperature too high Set the correct upstream temperature. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Operation 8.5 Faults 8.5.2 Mechanical faults NOTICE Damage to the machine caused by faults Correct the cause of the fault as specified in the remedial measures section. Repair any damage to the machine. Table 8-2 Mechanical faults Grinding noise Overheating Radial vibrations Axial vibrations Water drains out X X X X X X X Possible causes of faults Remedial measures Rotating parts are grinding Establish the cause and realign the parts. Cooling water switched off Switch the cooling water supply on. Rotor not balanced Decouple the rotor and then rebalance it. Rotor out of true, shaft bent Consult the manufacturing plant. Poor alignment Align the machine set and check the coupling. 1) Coupled machine not balanced Rebalance the coupled machine. X Shocks from coupled machine Examine the coupled machine. X X Imbalance originating from gearing Fix the gearing. X X Resonance with the foundations Stabilize the foundation following consultation. X X Changes in foundation Determine the cause of the changes and, if necessary, rectify. Realign the machine. Cooling water pipes defective Locate the non-watertight section and seal it or consult the manufacturer. X Water connection defective 1) Take into account possible changes which may occur during overheating. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 53 Operation 8.5 Faults 54 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Maintenance 9.1 9 Inspection and maintenance Observe the general safety instructions (Page 11) for all work on the machine. 9.1.1 Inspection Inspections in the event of faults Perform an inspection immediately in the event of faults or exceptional operating conditions indicating an electrical or mechanical overload, e.g., overload, short circuit. 9.1.1.1 Initial inspection Inspection interval for initial inspection The initial inspection once the three-phase motor is assembled and commissioned is, under normal circumstances, conducted after approx. 500 operating hours, but at the latest after 6 months. Conducting the initial inspection While the motor is running, check that: - The stated electrical characteristics are being observed. - The smooth running characteristics and running noises of the three-phase motor have not deteriorated. Once the machine has been shut down, check that: - The motor foundation has no indentations or cracks. Correct any deviations that are determined in the inspection without delay. NOTICE Adapt the inspection to the plant-specific conditions This list does not claim to be complete. Further tests also should be carried out in accordance with the additional instruction manuals (e.g. bearings, cooler, etc.) or in accordance with the particular system-specific conditions. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 55 Maintenance 9.1 Inspection and maintenance 9.1.1.2 General inspection Items for inspection Perform the following checks after approx. 16,000 operating hours or 2 years, whichever comes first: While the motor is running, check that: - The stated electrical characteristics are being observed - The smooth running characteristics and machine running noise have not deteriorated Once the machine has been shut down, check that: - The motor foundation has no indentations or cracks - The machine is aligned within the permissible tolerance ranges - All the fixing bolts/screws for the mechanical and electrical connections have been securely tightened - The winding insulation resistances are sufficiently high - Any bearing insulation has been fitted as shown on plates and labeling. - Cables and insulating parts and components are in good condition and there is no evidence of discoloring CAUTION If you detect any defects or malfunctions during the inspection, you must rectify them immediately. They may otherwise cause damage to the machine. 9.1.1.3 Rolling-contact bearing inspection Inspections in the event of faults Perform an inspection immediately in the event of faults or exceptional operating conditions indicating an electrical or mechanical overload, e.g., overload, short circuit. Inspecting rolling-contact bearings When inspecting rolling-contact bearings, it is generally not necessary to dismantle the machines. The motor only has to be dismantled if the bearings are to be replaced. Note Observe the regreasing intervals for the rolling-contact bearings The regreasing intervals for rolling-contact bearings are different from the inspection intervals. Failure to regrease the rolling-contact bearings at the specified intervals can result in them sustaining damage. Comply with the regreasing intervals for roller bearings, the regreasing intervals are specified on the lubricant plate. 56 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Maintenance 9.1 Inspection and maintenance 9.1.1.4 Changing bearings when using permanently lubricated rolling-contact bearings Note Permanently lubricated bearings The replacement of the permanently lubricated roller bearing is determined by the number of operating hours and is required around every three years. 9.1.2 Maintenance 9.1.2.1 Safety instructions for maintenance CAUTION Personal protective measures when working with compressed air When cleaning with compressed air, dust, metal chips, or cleaning agents can be whirled up. Injuries can result. When cleaning using compressed air, make sure you use suitable extraction equipment and wear protective equipment (safety goggles, protective suit, etc.). Note Operating conditions and characteristics can vary widely. For this reason, only general intervals for inspection and maintenance measures can be specified here. See also The five safety rules: (Page 11) 9.1.2.2 Maintenance intervals General Careful and regular maintenance, inspections, and overhauls are essential for detecting and eliminating faults in good time before they can cause any damage. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 57 Maintenance 9.1 Inspection and maintenance NOTICE Inspection if there are faults or unusual conditions Unusual conditions or faults that represent electrical or mechanical overstressing of the three-phase motor, such as overload, short circuit, etc. can cause consequential damage to the machine. If there are faults or unusual conditions such as overload or short circuit etc. immediately perform the inspections. Measures, maintenance intervals Operating conditions and characteristics can vary widely. For this reason, only general maintenance intervals can be specified here. Maintenance intervals should therefore be scheduled to suit the local conditions (fouling, switching frequency, load, etc.). Perform the following measures after the operation time or the interval specified in the following table elapses. Table 9-1 Measures after operating times or intervals measures Operating tines and intervals Initial inspection After 500 operating hours, at the latest after 1/2 years Regreasing See lubricant plate plate Permanent lubrication (with coupling output) Replace bearings after approximately 20,000 operating hours, at the latest after 3 years Cleaning Depending on degree of local fouling Main inspection After approximately 16,000 operating hours, at the latest after 2 years [ID: 357.01] 9.1.2.3 Rolling-contact bearings The motors have rolling-contact bearing bushes for grease lubrication. Depending on the version, the motors are permanently lubricated or are equipped with a regreasing device. Depending on the type of load, a deep-groove ball bearing or a cylindrical-roller bearing is fitted as a floating bearing on the drive end. For the bearing assignments as well as the associated permissible lateral forces and minimum loads when cylindrical-roller bearings are installed at the drive end, refer to the catalog or contact your sales partner. The DE bearing contains built-in compression springs that help to rebalance the axial play of the external bearing rings. 9.1.2.4 Cleaning the spent grease chamber The rolling-contact bearing's spent grease chamber only has room for a limited amount of spent grease. When the spent grease chamber is full, the spent grease must be removed, 58 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Maintenance 9.1 Inspection and maintenance otherwise it will penetrate into the interior of the machine. The amount of grease used for each regreasing operation is shown on the lubricant plate. When changing the bearings remove the spent grease that has collected in the spent grease chamber and in the outer bearing cover. To remove the spent grease, proceed as follows: 1. Remove the transmission element. 2. Remove the spent grease: - At the DE, unscrew the outer bearing cover and empty the spent grease from the outer bearing cover. - At the NDE, remove the cover of the speed sensor and the cover of the spent grease chamber. Empty the spent grease chamber. 9.1.2.5 Lubrication Regreasing intervals The regreasing intervals are specified on the lubricant plate of the motor. NOTICE Comply with the lubrication intervals The bearings can be damaged if the lubricating intervals are not maintained. Keep to the general lubrication interval, see Maintenance intervals. The lubrication intervals apply for normal loads, operation at speeds corresponding to those specified on the rating plate, precision-balanced running, almost neutral ambient air, and the use of high-quality rolling-contact bearing greases. Grease types The following high-quality rolling-contact bearing greases have been tested and are suitable: Table 9-2 Rolling-contact bearing greases K3N greases ESSO / Unirex N3 ARAL / Aralub 4340 DEA / Glissando 30 ESSO / Beacon 3 FUCHS / Renolit FWA 220 WINTERSHALL / Wiolub LFK 3 LUBRICANT CONSULT / Sintono GPE 702 These greases have lithium soap as the thickening agent and mineral oil as the base oil. They exceed the standard requirements of DIN 51825 in several important respects and are, therefore, compatible with the specified regreasing intervals. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 59 Maintenance 9.1 Inspection and maintenance NOTICE Damage from mixing lubrication types Mixing greases with different thickeners and thickening agents can worsen the lubricating properties of the rolling-contact bearing grease. This can damage the rolling-contact bearing. Never mix greases that have different thickening agents and different base oils. Initial lubrication ESSO / Unirex N3 grease is used for initial lubrication of the bearings (prior to delivery). Lubricating using the regreasing device A button head grease nipple in accordance with DIN 3404, size M10x1, is provided at both the drive end and the non-drive end for regreasing. Figure 9-1 Grease nipple 1. Clean the grease nipples at the DE and NDE. 2. Press in the type and quantity of grease specified on the lubricant plate. The shaft should rotate so that the new grease can be distributed throughout the bearing. The bearing temperature rises sharply at first, then drops to the normal value again after the excess grease has been displaced out of the bearing. 9.1.2.6 Maintaining the cooling water system The cooling water pipe system, made of high-grade steel, is maintenance-free if the required coooling water quality (Page 33) is maintained. 60 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Maintenance 9.2 Repair 9.2 Repair Observe the general safety instructions (Page 11) for all work on the machine. Note If the motor has to be transported, please observe the information and instructions in the "Transport" section. 9.2.1 Removing and installing the protecting ring The protecting ring acts as an outer bearing seal. It sits on the shaft outside the bearing end shield. Disassembly Once the coupling is detached, you can remove the protective ring from the shaft. After it has been removed, the protective ring will be deformed and must be replaced. Assembly Push the protecting ring over the end of the shaft. Make sure that the outer collar is placed at a spacing of 1 mm from the bearing end shield. = PP = Figure 9-2 Fitting the protecting ring A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 61 Maintenance 9.2 Repair 9.2.2 Connecting the speed encoder CAUTION Electrostatic discharge Electronic modules contain components that can be seriously damaged by electrostatic discharge. These modules can easily be destroyed unless they are handled properly. To protect your equipment against damage, follow the instructions given in the section headed "Electrostatic Sensitive Devices" (Page 15). 1. Insert the connector into the socket. 2. Press the cable into the holder provided for it. 3. Screw on the sensor cover. Take care that you do not catch the cable as you screw it in. Figure 9-3 9.2.3 Electrical connection of the speed sensor Replacing or adjusting the speed encoder Note Replacing or adjusting the speed encoder Replacing or adjusting the speed encoder in an incorrect manner can result in machine malfunctions. Arrange to have the speed encoder replaced or adjusted by Siemens service personnel. This will ensure problem-free functioning. 62 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Maintenance 9.2 Repair 9.2.4 Replacing the DRIVE-CLiQ interface (encoder module) Only trained Siemens service engineers are authorized to replace the DRIVE-CLiQ interface (sensor module). CAUTION Electrostatic discharge Electronic modules contain components that can be destroyed by electrostatic discharge. These modules can be easily destroyed by improper handling. To protect your equipment against damage, follow the instructions given in the chapter ESD Guidelines (Page 15). WARNING Motor-specific sensor module The Sensor Module contains motor-specific and sensor-specific data and an electronic nameplate. If you operate a different Sensor Module on the motor, this can result in serious injury or death, or cause considerable material damage. Only operate the sensor module on the original motor. Do not install the sensor module on other motors. Do not replace the sensor module with a sensor module from a different motor. 9.2.5 Screw-type connections Tightening torque for screwed union connections The screwed union connections with metal contact surfaces (end shields, active bearing parts, terminal box parts bolted onto the stator frame) should be tightened to the following torque with a tolerance of 10 %, depending on the thread size. Table 9-3 Tightening torque for screwed union connections Thread size Tightening torque [Nm] M6 M8 M10 M12 M16 M20 M24 8 20 40 70 170 340 600 Please refer to the relevant sections and drawings for all other tightening torques (electrical connections and bolted connections for parts with flat gaskets). Bolt locking devices Nuts or bolts that are mounted together with locking, resilient and/or force-distributing elements (e.g., safety plates, spring-lock washers, etc.) must be refitted together with identical, fully functional elements. Always replace keyed elements. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 63 Maintenance 9.2 Repair 64 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 10 Spare parts 10.1 Ordering data When ordering spare parts, in addition to the precise designation of the spare part, specify the motor type and the serial number of the motor. Ensure that the spare part designation matches the designation in the spare part lists and add the associated part number. Example: Spare parts kit, drive-end bearing (Part 3.00) Machine type 1PH81841JD202FA1 Serial number N-W91246206010001 The machine type and the serial number are indicated on the rating plate and in the technical data, and are also embossed on the drive end of the shaft. Note Bar code on rating plate You can also read the machine type and serial number from the bar code on the rating plate. The graphical representations in this chapter show schematic diagrams of the basic versions. They are used for spare parts definitions. The supplied version may differ in details from these representations. 10.2 Spare parts kits The spare parts are bundled with the necessary wearing parts in a logical way so as to create spare parts kits. The spare parts kits for the bearings also contain the bearing grease. The following spare parts kits are available for you to order: 3.00 Spare parts kit, drive-end bearing (complete) 4.00 Spare parts kit, non-drive-end bearing (complete) 55.00 Spare parts kit, relevant version of speed encoder Additional spare parts are available on request. For an overview of the services available from Technical Support, please visit: Technical Support (http://support.automation.siemens.com/WW/view/en/16605654) If you wish to submit a service request directly, you can do so via the following page: http://www.siemens.com/automation/support-request (http://www.siemens.com/automation/support-request) A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 65 Spare parts 10.3 Ordering spare parts from Spares on Web 10.3 Ordering spare parts from Spares on Web Spare parts can be ordered online from the spare parts service "Spares on Web" (https://b2b-extern.automation.siemens.com/spares_on_web). You can use "Spares on Web" to determine the order numbers for motor spare parts quickly and easily. A short description of how to use "Spares on Web" is available on the Internet (http://support.automation.siemens.com/WW/news/en/25248626). 66 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Spare parts 10.4 Motor, complete 10.4 Motor, complete Figure 10-1 Schematic diagram of motor (complete) Table 10-1 Motor, complete Number Designation Number Designation 3.00 Spare parts kit, drive-end bearing 8.00* Rotor, complete 4.00 Spare parts kit, non-drive-end bearing 10.00* Stator housing (with laminated core, winding and cooling water pipe system) 55.00 Spare parts kit, speed encoder 10.35* Hoisting lug 5.00* Bearing shield, drive end 20.00* Terminal box 6.00* Bearing shield, non-drive end 99.00* Special built-on parts * On request A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 67 Spare parts 10.5 Rolling-contact bearing bush drive end, mounted gearing, with regreasing 10.5 Rolling-contact bearing bush drive end, mounted gearing, with regreasing Figure 10-2 Rolling-contact bearing bush drive end with mounted gearing, with regreasing Table 10-2 Spare parts for rolling-contact bearing bush drive end with mounted gearing, with regreasing Number Designation Number Designation 3.00 Spare parts kit, drive-end bearing Deep-groove ball bearing (floating bearing) Radial shaft sealing ring Inner ring 3.60* Inner bearing cover 3.20* Outer bearing cover 3.80* Grease nipple 3.45* Corrugated spring/compression springs * On request 68 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Spare parts 10.6 Rolling-contact bearing bush drive end, belt coupling 10.6 Rolling-contact bearing bush drive end, belt coupling Figure 10-3 Rolling-contact bearing bush drive end with belt coupling, with regreasing Table 10-3 Spare parts for rolling-contact bearing bush drive end with belt coupling, with regreasing Number Designation Number Designation 3.00 Spare parts kit, drive-end bearing Cylindrical-roller bearing (floating bearing) Protecting ring (rotating) 3.60* Inner bearing cover 3.20* Outer bearing cover 3.80* Grease nipple * On request A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 69 Spare parts 10.7 Rolling-contact bearing bush drive end, coupling output, with regreasing 10.7 Rolling-contact bearing bush drive end, coupling output, with regreasing Figure 10-4 Rolling-contact bearing bush drive end, with coupling output, with regreasing Table 10-4 Spare parts for rolling-contact bearing bush drive end, with coupling output, with regreasing Number Designation Number Designation 3.00 Spare parts kit, drive-end bearing Deep-groove ball bearing (floating bearing) Protecting ring (rotating) 3.60* Inner bearing cover 3.20* Outer bearing cover 3.80* Grease nipple 3.45* Corrugated spring * On request 70 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Spare parts 10.8 Rolling-contact bearing bush drive end, coupling output, with permanent lubrication 10.8 Rolling-contact bearing bush drive end, coupling output, with permanent lubrication Figure 10-5 Rolling-contact bearing bush drive end, with coupling output, with permanent lubrication Table 10-5 Spare parts for rolling-contact bearing bush drive end, with coupling output, with permanent lubrication Number Designation 3.00 Spare parts kit, drive-end bearing Deep-groove ball bearing (floating bearing) Protecting ring (rotating) 3.45* Corrugated spring/compression springs * On request A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 71 Spare parts 10.9 Rolling-contact bearing bush non-drive end, with permanent lubrication 10.9 Rolling-contact bearing bush non-drive end, with permanent lubrication Figure 10-6 Rolling-contact bearing bush non-drive end, permanent lubrication Table 10-6 Spare parts for rolling-contact bearing bush non-drive end, permanent lubrication Number Designation 4.00 Spare parts kit, non-drive-end bearing Deep-groove ball bearing (locating bearing) Retaining ring 4.60* Inner bearing cover * On request 72 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Spare parts 10.10 Rolling-contact bearing bush non-drive end, with regreasing (shaft height 180, 225) 10.10 Rolling-contact bearing bush non-drive end, with regreasing (shaft height 180, 225) Figure 10-7 Rolling-contact bearing bush non-drive end, with regreasing, shaft height 180 / 225 Table 10-7 Spare parts for rolling-contact bearing bush non-drive end, with regreasing, shaft height 180 / 225 Number Designation Number Designation 4.00 Spare parts kit, non-drive-end bearing Deep-groove ball bearing (locating bearing) Retaining ring 4.80* Grease nipple 4.60* Inner bearing cover 4.90* Cover of spent grease chamber * On request A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 73 Spare parts 10.11 Terminal box 10.11 Terminal box Figure 10-8 Terminal box Table 10-8 Spare parts for terminal box Number Designation Number Designation 20.20* Enclosure 20.50* Entry plate 20.30* Cover 20.60* Adapter plate (optional) * On request 74 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Spare parts 10.12 Speed encoder 10.12 Speed encoder Figure 10-9 Table 10-9 Speed encoder Spare parts for the speed encoder Part Description 55.00 Spare parts kit, speed encoder Speed encoder Torque arm 6.80* Cover * On request A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 75 Spare parts 10.12 Speed encoder 76 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 11 Disposal 11.1 Introduction Protecting the environment and preserving its resources are corporate goals of the highest priority for us. Our worldwide environmental management system to ISO 14001 ensures compliance with legislation and sets high standards in this regard. Environmentally friendly design, technical safety and health protection are always firm goals even at the product development stage. Recommendations for the environmentally friendly disposal of the machine and its components are given in the following section. Be sure to comply with local disposal regulations. 11.2 Preparing for disassembly Disassembly of the machine must be carried out and/or supervised by qualied personnel with appropriate expert knowledge. 1. Contact a certified waste disposal organization in your vicinity. Clarify what is expected in terms of the quality of dismantling the machine and provision of the components. 2. Follow the five safety rules (Page 11). 3. Disconnect all electrical connections. 4. Remove all liquids such as oil, water, ... 5. Remove all cables. 6. Deatch the machine fixings. 7. Transport the machine to a suitable location for disassembly. Refer also to the information in the section headed "Maintenance" (Page 55). 11.3 Working on machines with permanent magnets On machines with permanent magnets, the magnetic field is guided in an assembled state in the magnetic circuit of the motor. This means that no magnetic fields, which may be to your health, are detectable outside the machine. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 77 Disposal 11.4 Disposing of permanent magnets WARNING Strong magnetic field when the machine is open A strong magnetic field is always present inside the machine. If the housing is open, e.g. when maintenance openings are open or when working inside the machine, magnetic objects can be suddenly attracted by this magnetic field. This can result in death, severe injury or material damage. Working in the vicinity of the rotor is only permitted in exceptional circumstances. Unambiguous access rules must be established in accordance with the magnetic fields prevailing in the workplace. Clearly mark the boundaries of the areas where standing is permitted. People who need to use electronic or magnetic medical aids such as pacemakers, hearing aids, implants or similar devices, are at particularly high risk. Such persons must undergo an industrial medicine assessment. Observe the following measures. Personal protective measures Ensure that you never wear or carry any of the following objects and that they are kept a safe distance from the machine: - All kinds of magnetic metal parts such as, keys, glasses, tools, knives, scissors, tape measures, etc. - Magnetic jewelry such as rings, chains, needles, watches, etc. - Electronic devices and data carriers such as service cards, check cards, credit cards, calculators, cell phones, etc. - Wallets or other iron-containing objects - Electrically conductive foreign bodies Do not use any magnetic tools or lifting devices. Wear only occupational safety items without magnetic metal parts, e.g. occupational safety shoes with non-magnetic protective caps and soles. Keep your shoes and clothing free from chips and waste containing iron. Exercise caution when installing accessories. Ensure that no parts fall into the inside of the machine. Do not perform any cutting at the machine, e.g. manufacturing threaded holes. Any exceptions require written approval from the manufacturer. 11.4 Disposing of permanent magnets If the entire motor is melted down, no special action is required for the permanent magnets. Remove all cables before the melting process. 78 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Disposal 11.5 Disposal of components Description If the motor is disassembled and dismantled, the permanent magnets must be demagnetized. For this purpose, the motor should be heated to 350 C. This is necessary to ensure that no hazards result from the rotors during and after disposal. The disposal must be carried out by an authorized waste disposal company. NOTICE Removing the permanent magnet rotor Only authorized workshops and waste disposal companies are permitted to remove the permanent magnet rotor. Demagnetizing the rotors Waste disposal companies that are authorized to demagnetize rotors use a specially designed disposal furnace. The insides of the disposal furnace consist of non-magnetic material. The rotors are put in the furnace in a solid, heat-resistant container made of nonmagnetic material and left in the furnace during the entire demagnetization procedure. Demagnetization is achieved by heating the rotor in the furnace until the permanent magnets have reached a temperature of 350 C. NOTICE Preventing emissions Escaping exhaust must be collected and rendered harmless without damaging the environment. Note Authorized waste disposal companies Information regarding authorized waste disposal companies and workshops can be obtained from the Siemens Service Center. 11.5 Disposal of components Components The machines consist for the most part of steel and various proportions of copper and aluminum. Metals are generally considered to be unlimitedly recyclable. Sort the components for recycling according to whether they are: Iron and steel Aluminum Non-ferrous metal, e.g. windings The winding insulation is incinerated during copper recycling. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 79 Disposal 11.5 Disposal of components Insulating materials Cables for printers with Electronic waste Process materials and chemicals Sort the process materials and chemicals for recycling according to whether they are for example: Oil Grease Cleaning substances and solvents Paint residues Anti-corrosion agent Dispose of the separated components according to local regulations or via a specialist disposal company. The same goes for cloths and cleaning substances which have been used while working on the machine. Packaging material If necessary, contact a suitable specialist disposal company. Wooden packaging for sea transport consists of impregnated wood. Observe the local regulations. The foil used for water-proof packaging is an aluminum composite foil. It can be recycled thermically. Dirty foil must be disposed of via waste incineration. 80 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 A Appendix A.1 Siemens Service Center Contact for further information Details regarding the design of this electrical machine and the permissible operating conditions are described in these operating instructions. Field service visits/Spare parts If you wish to request a field service visit or order spare parts, please contact your local Siemens sales office. This office will contact the responsible service center on your behalf. Technical queries/Additional information If you have any technical queries or you require additional information, please contact the Siemens Service Center. Please have the following machine data ready: Machine type Machine number You can find this data on the rating plate of the machine. Table A-1 Siemens Service Center contact details Europe - Germany: Phone: Fax +49 (0)180 - 50 50 223 America - USA: Phone: +1 423 262 2522 Asia - China: Phone: +86 1064 719 990 +49 (0)180 - 50 50 222 E-Mail: LD.Service.AuD@Siemens.com (mailto:LD.Service.AuD@Siemens.com) Internet: Support Request (http://www.siemens.com/automation/support-request) 0,14 /Min. from German landlines, mobile phone prices may differ. A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 81 Appendix A.2 EC Declaration of Conformity A.2 82 EC Declaration of Conformity A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Appendix A.2 EC Declaration of Conformity A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 83 Appendix A.2 EC Declaration of Conformity 84 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Appendix A.2 EC Declaration of Conformity A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 85 Appendix A.2 EC Declaration of Conformity 86 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Appendix A.2 EC Declaration of Conformity A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 87 Appendix A.2 EC Declaration of Conformity 88 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Index A Alignment accuracy, 29 Anti-freeze, 26 Anti-freeze protection, 26 B Balance quality, 30 Bearing currents, 41 Bearing seizure damage, 24 C Cable entry, 35 Cable lugs, 37 Cable selection, 39 Circuit breaker, 43 Circuit diagram, 39 Cleaning, 58 Spent grease chamber, 59 Condensation, 26, 32, 50 Connection Electrical, 36 Temperature sensor, 40 Contact, 81 Converter output terminals, 43, 49 Cooling, 19 Cooling capacity, 19 Cooling method, 19 Cooling water Connection, 34 Inlet water temperature, 33 Specification, 33 Cooling water supply, 50 Components, 79 DRIVE-CLiQ, 35, 63 E Electromagnetic compatibility, 16 Electromagnetic fields, 16 Emitted interference, 16 Environmental requirements, 20 Equipotential bonding, 39 Equipotential bonding conductor, 41 ESD guidelines, 15 F Faults, 50 Electrical, 52 Mechanical, 53 Feather key, 31 Field service visit, 81 Five safety rules, 11 Fixing Flange, 30 Motor feet, 30 Flammable substances, 13 Flange-mounted motors, 30 Fusing the cable sections, 43 G General inspection, 56 Grease types, 59 H Hazardous substances, 13 Hot surfaces, 13 D Damage during transportation, 21 Prevention, 23 Degree of protection, 19 Demagnetization Rotor, 79 Disposal Chemicals, 80 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 I Initial inspection, 55, 58 Initial lubrication, 60 Inlet water temperature, 33 Inspection interval, 55 Insulation resistance, 45 89 Index Interference immunity, 16 L Live parts, 12 Long-term storage, 25 Versions, 20 Rolling-contact bearings Inspection, 56 Rotating parts, 13 Rotor, 18, 79 Demagnetizing, 79 Rotor shipping brace, 23 Tightening torque, 24 M Machine Aligning, 28 Machine design, 18 IEC, 18 Magnetic field, 14, 78 Main inspection, 58 Maintenance Cooling water system, 60 Maintenance intervals, 58 Maximum rotational speed, 47 Motor shaft, 43, 49 N Noise emissions, 27 O Operating pressure, 34 Output element, 31 P Permanent lubrication, 58 Permanent magnet, 14, 78 Pressure drop, 34 Protecting ring, 61 Q Qualified personnel, 12 R Rating plate, 17 Bar code, 65 Regreasing, 58 Regreasing device, 58, 60 Regreasing interval, 56, 59 Roller bearings 90 S Safety information Flammable substances, 13 Hazardous substances, 13 Hot surfaces, 13 Live parts, 12 Rotating components, 13 Sensor module, 63 Siemens Service Center, 81 Spare parts, 65 Motor, 67 Ordering, 66 Rolling-contact bearing bush, drive end, 68, 69, 70, 71 Rolling-contact bearing bush, non-drive end, 72, 73 Speed encoder, 75 Terminal box, 74 Spare parts kits, 65 Spare parts ordering, 65 Spares on Web, 66 Speed encoder Adjusting, 62 Electrical connection, 62 Replacing, 62 Spent grease chamber, 59 storage Indoor, 25 Switching off, 51 Switching on, 47 T Terminal box, 36 Terminal designation, 37 Tightening torque Contact nuts, 38 Fixing bolts, 38 Screwed union connections, 63 Transporting, 21 Transverse forces, 20 Type of balancing, 30 Types of construction, 19 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 Index V Voltage at the motor terminals, 43, 49 Voltage via the converter, 43, 49 W Water drainage hole, 26, 31 A5E02446774A AB Siemens AG Operating Instructions V2.00 1PH8 91 AF EG Konformitatserklarung 1PH8 18/22/28