CLC014 CLC014 Adaptive Cable Equalizer for High-Speed Data Recovery Literature Number: SNLS010D CLC014 August 20, 2010 Adaptive Cable Equalizer for High-Speed Data Recovery CLC014 is insensitive to the pathological patterns inherent in the video industry standards. General Description National's CLC014 adaptive cable equalizer is a low-cost monolithic solution for equalizing data transmitted over cable (or any media with similar dispersive loss characteristics). The CLC014 simplifies the task of high-speed data recovery with a one-chip solution and a minimal number of external components. The equalizer automatically adapts to equalize any cable length from zero meters to lengths that attenuate the signal by 40 dB at 200 MHz. This corresponds to 300 meters of Belden 8281 or 120 meters of Category 5 UTP (unshielded twisted pair). The CLC014 provides superior jitter performance: 180pspp for 270 Mbps data that has passed through 200 meters of Belden 8281 cable. This exceptional performance provides wide error margin in digital data links. The equalizer operates on a single supply with a power consumption of only 290 mW. The small 14-pin SOIC package allows for high-density placement of components for multichannel applications such as routers. The equalizer operates over a wide range of data rates from less than 50 Mbps to rates in excess of 650 Mbps. The equalizer is flexible in allowing either single-ended or differential input drive. Its high common mode rejection provides excellent immunity to interference from noise sources. Onchip quantized feedback eliminates baseline wander. Additional features include a carrier detect output and an output mute pin which, when tied together, mute the output when no signal is present. A buffered eye monitor output is provided, for viewing the equalized signal prior to the comparator. Differential AEC pins allow the user to set the internal adaptive loop time constant with one external capacitor. Also, the Features Automatic equalization of coaxial and twisted pair cables Carrier detection and output mute Output eye monitor Single supply operation: +5V or -5.2V Single-ended or differential input Low cost Applications SMPTE 259M serial digital interfaces: NTSC/PAL, 4:2:2 component and wide screen; also 540 Mbps (4:4:4:4) Serial digital video routing and distribution Serial digital data equalization and reception Data recovery equalization: ATM, CAD networks, medical, set top terminals, industrial video networks Key Specifications Low jitter: 180pspp @ 270 Mbps through 200 meters of Belden 8281 coaxial cable High data rates: < 50 Mbps to > 650 Mbps Excellent input return loss: 19 dB @ 270 MHz Low supply current: 58 mA Equalizes up to 300+ meters of Belden 8281 or 120 meters of Cat 5 UTP cable Typical Application 10005604 (c) 2010 National Semiconductor Corporation 100056 100056 Version 11 Revision 6 www.national.com Print Date/Time: 2010/08/23 16:48:25 CLC014 Adaptive Cable Equalizer for High-Speed Data Recovery OBSOLETE CLC014 10005602 10005603 Connection Diagram Pinout SOIC 10005601 14-Pin SOIC Order Number CLC014AJE See NS Package Number M14A www.national.com 2 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC-VEE) Maximum Junction Temperature Storage Temperature Range Lead Temperature (Soldering 4 sec.) ESD Rating (Note 14) 100 1.0 F AEC Capacitor (Connected between AEC+ & AEC-) Cable Input Voltage Swing (Note 4) DO/DO Minimum Voltage (Note 15) -0.3V, +6.5V +150C -65C to +150C 50 pF to 1 F 720 to 880 mVpp VCC-1.6V +260C <500V JA 14-Pin SOIC (AJE) MTTF (based on limited life test data) 95C/W 4.8 x 107 hours Recommended Operating Conditions Supply Voltage (VCC-VEE) Operating Temperature Range 4.5V to 5.5V -40C to +85C Electrical Characteristics (VCC = +5V, VEE = 0V, signal source swing = 0.8 Vpp(Note 4), CAEC = 100 pF) Parameter Conditions Typ +25C Min/Max +25C Min/Max -40C to +85C Units DYNAMIC PERFORMANCE Residual Jitter 100 meters Belden 8281 270 Mbps PRN (Note 5) 150 250 400 pspp 200 meters Belden 8281 270 Mbps PRN (Note 5) 180 250 400 pspp 300 meters Belden 8281 270 Mbps PRN (Note 3, Note 5) 350 500 750 pspp 100 meters Belden 8281 CAEC = 100 pF (Note 6) 1.5 _ _ s 200 meters Belden 8281 CAEC = 100 pF (Note 6) 2.0 _ _ s 300 meters Belden 8281 CAEC = 100 pF (Note 6) 3.2 _ _ s Rcollector = 75 750 _ _ ps Equalization Time Constant output rise and fall time (20%-80%) output duty cycle distortion 30 _ _ ps 1/50 _ _ trans/ns 650 _ _ Mbps 27 MHz 0.85 _ _ ns/V 270 MHz 1.90 _ _ ns/V 27 MHz 0.55 _ _ ns/V 270 MHz 1.45 _ _ ns/V minimum average transition density maximum average data rate 150m Belden 8281 (Note 7) VCC Jitter Sensitivity VEE Jitter Sensitivity STATIC PERFORMANCE Supply Current (Includes Output Current) VAEC = 0V (Note 3) 58 48/68 40/75 mA VAEC = 0.4V (Note 3) 53 43/64 37/70 mA 10 8.7/11.3 8.0/12 mA Rcollector = 75 (Note 3) 750 650/850 600/900 mV 3.4 _ _ V 1.5 _ _ mV/meter Input and Output Parameters DO/DO output current DO/DO output voltage swing DI/DI common mode voltage AEC differential voltage Belden 8281 3 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 www.national.com CLC014 Series Input Resistance (In Series w/DI & DI) Input Coupling Capacitance Absolute Maximum Ratings (Note 1) CLC014 Parameter Conditions AEC+/AEC- common mode output eye monitor (OEM) bias potential Typ +25C Min/Max +25C Min/Max -40C to +85C Units 3.6 _ _ V 3.2 _ _ V carrier detect (CD) current output-HIGH CD VOH = 4.5V -400 _ _ A carrier detect (CD) current output-LOW CD VOL = 0.5V 600 _ _ A MUTE voltage input-HIGH (Note 3) 1.8 2.0 2.0 V MUTE voltage input-LOW (Note 3) 1.2 0.8 0.8 V MUTE current input-HIGH VIH = 5V (Note 3) 5.0 100 500 nA MUTE current input-LOW VIL = 0V (Note 3) 0.2 100 500 nA carrier applied (Note 8) 1.0 _ _ s carrier removed (Note 9) 12 _ _ s MUTE response time (Note 10) 2.0 _ _ ns input resistance single-ended 7.3 _ _ k input capacitance single-ended (Note 11) 1.0 _ _ pF input return loss @ 270 MHz Zo = 75 (Note 12) 19 _ _ dB maximum cable attenuation 200 MHz (Note 13) 40 _ _ dB TIMING PERFORMANCE CD Response Time MISCELLANEOUS PERFORMANCE Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of "Electrical Characteristics" specifies conditions of device operation. Note 2: Min/max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are determined from tested parameters. Note 3: J-level: spec. is 100% tested at +25C. Note 4: These specifications assume an 800 mVpp signal at the cable input. Levels above and below 800 mV are allowable, but performance may vary. The cable will attenuate the signal prior to entering the equalizer. Note 5: Peak-to-peak jitter is defined as 6 times the rms jitter. Note 6: For more information, see "CLC014 Operation" and "Design Guidelines". Note 7: 50% eye opening. Note 8: Time from application of a valid signal to when the CD output asserts high. Note 9: Time from the removal of a valid signal to when the CD output asserts low. Note 10: Time from assertion of MUTE to when the output responds. Note 11: Device only. Does not include typical pc board parasitics. Note 12: Includes typical pc board parasitics. Note 13: This sets the maximum cable length for the equalizer. Note 14: Human body model, 1.5 k in series with 100 pF; based on limited test data. Note 15: To maintain specified performance, do not reduce DO/DO below this level. www.national.com 4 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 CLC014 Typical Performance Characteristics 10005605 10005608 10005606 10005609 10005607 10005610 5 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 www.national.com CLC014 10005611 10005614 10005612 10005615 10005613 10005616 www.national.com 6 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 CLC014 10005618 10005617 10005619 7 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 www.national.com CLC014 cable or twisted pair. Its transfer function approximates the reciprocal of the cable loss characteristic. The block diagram in Figure 2 depicts the main signal conditioning blocks for equalizing digital data at the receiving end of a cable. The CLC014 receives baseband differential or single-ended digital signals at its inputs DI and DI. The Equalizer block is a two-stage adaptive filter. This filter is capable of equalizing cable lengths from zero meters to lengths that require 40 dB of boost at 200 MHz. The Quantized Feedback Comparator block receives the differential signals from the equalizer filter block. This block includes two comparators. The first comparator incorporates a self-biasing DC restore circuit. This is followed by a second high-speed comparator with output mute capability. The second comparator receives and slices the DC-restored data. Its outputs DO and DO are taken from the collectors of the output transistors. MUTE latches DO and DO when a TTL logic low level is applied. The Adaptive Servo Control block produces the signal for controlling the filter block, and outputs a voltage proportional to cable length. It receives differential signals from the output of the filter block and from the quantized-feedback comparator (QFBC) to develop the control signal. The servo loop response is controlled by an external capacitor placed across the AEC+ and AEC- pins. Its output voltage, as measured differentially across AEC+ and AEC-, is roughly proportional to the length of the transmission line. For Belden 8281 coaxial cable this differential voltage is about 1.5 mV/meter. Once this voltage exceeds 500 mV, no additional equalization is provided. The Carrier Detect (CD) block monitors the signal power out of the equalizing filter and compares it to an internal reference to determine if a valid signal is present. A CMOS high output indicates that data is present. The output of CD can be connected to the MUTE input to automatically latch the outputs (DO and DO), preventing random transitions when no data is present. The Output Eye Monitor (OEM) provides a single-ended buffered output for observing the equalized eye pattern. The OEM output is a low impedance high-speed voltage driver capable of driving an AC-coupled 100 load. Pin Definitions Name Pin # DI, DI DO, DO 8, 9 Description Differential data inputs. 13, 14 Differential collector data outputs (ECL compatible). AEC+, AEC- 6, 7 AEC loop filter pins. A capacitor connected between these pins governs the loop response for the adaptive equalization loop. OEM 3 Eye monitor output. The output of the equalization filter. CD 5 Carrier detect. (Low when no signal is present). MUTE 12 Output MUTE. (Active low.) Carrier detect may be tied to this pin to inhibit the output when no signal is present. VCC 1, 2, 4 Positive supply pins (ground or +5V). VEE 10, 11 Negative supply pins (-5.2V or ground). Operation The CLC014 Adaptive Cable Equalizer provides a complete solution for equalizing high-bit-rate digital data transmitted over long transmission lines. The following sections furnish design and application information to assist in completing a successful design: * Block diagram explanation of the CLC014 * Recommended standard input and output interface connections * Common applications for the CLC014 * Measurement, PC layout, and cable emulation boxes For applications assistance in the U.S., call 800-272-9959 to contact a technical staff member. 10005620 FIGURE 1. CLC014 Equalizer Application Circuit 10005621 BLOCK DESCRIPTION The CLC014 is an adaptive equalizer that reconstructs serial digital data received from transmission lines such as coaxial www.national.com FIGURE 2. CLC014 Block Diagram 8 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 CLC014 DEVICE TESTING Performance or compliancy testing of the CLC014 with Cable Clones is not allowed. Use of these devices is contrary to the product's specifications and test procedures. Testing for product specifications or performance using cable clones is invalid since cable clones have a different frequency response than the actual cable. Testing with full length cable samples is recommended. Input Interfacing The CLC014 accepts either differential or single-ended input voltage specified in Static Performance. The following sections show several suggestions for interfaces for the inputs and outputs of the CLC014. 10005624 FIGURE 4. Twisted Pair Input Interface Output Interfacing SINGLE-ENDED INPUT INTERFACE: 75 Coaxial Cable The input is connected single-ended to either DI or DI as shown in Figure 3. Balancing unused inputs helps to lessen the effects of noise. Use the equivalent termination of 37.5 to balance the input impedance seen by each pin. It also helps to terminate grounds at a common point. Resistors Rx and R y are recommended for optimum performance. The equalizer inputs are self-biasing. Signals should be AC coupled to the inputs as shown in Figure 3. The outputs DO and DO produce ECL logic levels when the recommended output termination networks are used. The DO and DO pins are not complementary emitter coupled logic outputs. Instead, the outputs are taken off of the collectors of the transistors. Therefore, care must be taken to meet the interface threshold levels required by ECL families. Recommended interfaces for standard ECL families are shown in the following circuits. DIFFERENTIAL LOAD-TERMINATED OUTPUT INTERFACE Figure 5 shows a recommended circuit for implementing a differential output that is terminated at the load. A diode or 75 resistor provides a voltage drop from the positive supply (+5V for PECL or Ground for ECL operation) to establish proper ECL levels. The resistors terminate the cable to the characteristic impedance. The output voltage swing is determined by the CLC014 output current (10 mA) times the termination resistor. For the circuit in Figure 5, the nominal output voltage swing is 750 mV. 10005622 FIGURE 3. Single-Ended 75 Cable Input Interface DIFFERENTIAL INPUT INTERFACE: Twisted Pair A recommended differential input interface is shown in Figure 4. Proper voltage levels must be furnished to the input pins and the proper cable terminating impedance must be provided. For Category 5 UTP this is approximately 100. Figure 4 shows a generalized network which may be used to receive data over a twisted pair. Resistors R1 and R2 provide the proper terminating impedance and signal level adjustment. The blocking capacitors provide AC coupling of the attenuated signal levels. The plots in the Typical Performance Characteristics section demonstrate various equalized data rates using Category 5 UTP at 100 meter lengths. A full schematic of a recommended driver and receiver circuit for 100 Category 5 UTP is provided in the Typical Applications section with further explanation. 10005625 FIGURE 5. Differential Load Terminated Output Interface DIFFERENTIAL SOURCE-TERMINATED OUTPUT INTERFACE Figure 6 is similar to Figure 5 except that the termination is provided at the source. This configuration may also be used for single-ended applications. However, the unused output must still be terminated as shown. 9 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 www.national.com CLC014 For example, a CAEC value of 100 pF results in an adaptive loop time constant of 2 s at 200 meters of cable. CONNECTION AND OPERATION OF CD AND MUTE Carrier Detect (CD) is a CMOS output that indicates the presence of equalized data from the filter. This CD output can be connected to MUTE to suspend changes in the data outputs DO and DO, if no valid signal exists. This simple configuration prevents random output transitions due to noise. For sparse transition patterns it is recommended that a capacitor be connected to CD as shown in Figure 1. Add a capacitor to pin 5 to slow the response time of Carrier Detect when Carrier Detect is connected to MUTE. The capacitor reduces sensitivity to pathological patterns. Pathological patterns are defined as sparse data sequences with few transitions. 10005626 FIGURE 6. Differential Source Terminated Output Interface OUTPUT EYE MONITOR OEM CONNECTIONS The OEM is a high-speed, buffered output for monitoring the equalized eye pattern prior to the output comparator. Its output is designed to drive an AC-coupled 50 coaxial cable with a series 50 backmatch resistor. The cable should be terminated with 50 at the oscilloscope. Figure 1 shows a schematic with a typical connection. TERMINATING PHYSICALLY SEPARATED OUTPUTS When the two outputs must be routed to physically separate locations, the circuit in Figure 6 may be applied. Alternatively, if load termination is desired, the circuit in Figure 7 may be used. The resistive divider network provides 75 termination and establishes proper ECL levels. This circuit consumes slightly more power than the previous circuits. MINIMUM DATA TRANSITIONS The CLC014 specifies a minimum transition rate. For the CLC014 this sets the minimum data rate for transmitting data through any cable medium. The CLC014 minimum average transition density is found in the Electrical Characteristics section of the datasheet. POWER SUPPLY OPERATION AND THERMAL CONSIDERATIONS The CLC014 operates from either +5V or -5.2V single supplies. Refer to Figure 1 when operating the part from +5V. When operating with a -5.2V supply, the VEE pins should be bypassed to ground. The evaluation board and associated literature provide for operation from either supply. Maximum power dissipation occurs at minimum cable length. Under that condition, ICC = 58 mA. Total power dissipated: PT = (58 mA)(5V) = 290 mW Power in the load: PL = (0.7V)(11 mA) + (37.5)(11 mA)2 = 12 mW Maximum power dissipated on the die: PDMAX = PT-PL = 278 mW Junction Temperature = 10005627 FIGURE 7. Alternative Load Terminated Output Interface Design Guidelines SELECTING THE AUTOMATIC EQUALIZER CAPACITOR The AEC capacitor sets the loop time constant for the equalizer's adaptive loop response time. The following formula is used to set the loop time constant: (JA)(278 mW) + TA = T A + 26C = R * CAEC * 10 -6 R is a conversion factor that is set by internal equalizer parameters and cable length. For Belden 8281 coaxial cable, the R values are ( = s, CAEC in pF): Cable Length R Value (Ohms) 100 meters 200 meters 300 meters 15000 20000 32000 www.national.com 10 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 The printed circuit board layout for the CLC014 requires proper high-speed layout to achieve the performance specifications found in the datasheet. The following list contains a few rules to follow: 1. Use a ground plane. 2. Decouple power pins with 0.1 F capacitors placed 0.1" (3mm) from the power pins. 3. Design transmission strip lines from the CLC014's input and output pins to the board connectors. 4. Route outputs away from inputs. 5. Keep ground plane 0.025" (0.06mm) away from the input and output pads. 10005628 FIGURE 8. Typical Measurement Block Troubleshooting with scope probes can affect the equalization. For high data rates, use a low capacitance probe with less than 2 pF probe capacitance. Evaluation boards and literature are available for quick prototyping and evaluation of the CLC014 Adaptive Cable Equalizer. The CLC014 contains CMOS devices and operators should use grounding straps when handling the parts. Figure 9 shows the CLC014's internal power supply routing. Bypass VCC (pin 4) by: * Monolithic capacitor of about 0.1 F placed less than 0.1" (3mm) from the pin * Tantalum capacitor of about 6.8 F for large current signal swings placed as close as convenient to the CLC014 10005629 FIGURE 9. Power Package Routing Fixture 11 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 www.national.com CLC014 Figure 8 shows a block level measurement diagram, while Figure 15 on depicts a detailed schematic. A pseudo-random pattern generator with low output jitter was used to provide a NRZI pattern to create the eye diagrams shown in the Typical Performance Characteristics section. Since most pattern generators have a 50 output impedance, a translation can be accomplished using a CLC006 Cable Driver as an impedance transformer. A wide bandwidth oscilloscope is needed to observe the high data rate eye pattern. When monitoring a single output that is terminated at both the equalizer output and the oscilloscope, the effective output load is 37.5. Consequently, the signal swing is half that observed for a single-ended 75 termination. Layout and Measurement CLC014 To minimize ringing at the CLC014's inputs, place a 100 resistor in series with the input. This resistor reduces inductance effects. Several layout techniques can improve high speed performance: * Keep input, output and AEC traces well separated * Use balanced input termination's * Avoid routing traces close to the CLC014's input trace * Maintain common return points for components * Use guard traces The input lines of the CLC014 use a 100 series resistors at the input pins. This decreases the inductive effects internal to the part to reduce ringing on fast rise and fall times. Refer to the evaluation board layout for further suggestions on layout for the CLC014 Adaptive Equalizer. CABLE EMULATION BOXES Some cable emulation boxes will not mimic cables correctly. When evaluating the CLC014, it is strongly recommended that actual cable be used to determine the various performance parameters. Typical Applications COAXIAL CABLE RECEIVER (Page 1) The CLC014 equalizer application shown on page 1 will equalize a variety of coaxial cables up to lengths that attenuate the signal by 40 dB at 200 MHz. The application shows the proper connection for a single cable driven with a CLC006 driver. Carrier Detect (CD) is connected to MUTE to latch outputs DO and DO in the absence of an input signal to the equalizer. Refer to the CLC014's evaluation board layout for additional suggestions. National can supply most of the major components required to design a transmission line repeater. Figure 11 shows a typical repeater design using the CLC006, CLC014, and the CLC016. The design functions supported by each chip are: CLC006: Cable connection chip Boosts drive for transmission to next repeater or final destinations CLC014: Receive serialized digital data from incoming transmission lines Equalizes the incoming data CLC016: Retimes the equalized data (improving jitter) EQUALIZATION CURVE The CLC014 Adaptive Cable Equalizer has a maximum equalization response as shown in Figure 10. This response may be obtained by forcing >0.5V differentially at the AEC pins. The CLC016 is a multi-rate data retiming PLL. The circuit (Figure 11) will work at up to 4 different data rates with no additional components or manual tuning. 10005630 FIGURE 10. Maximum Equalization Response www.national.com 12 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 CLC014 10005631 FIGURE 11. Typical Repeater Design DIGITAL VIDEO (SDV) ROUTERS The CLC014 provides performance that complies with the SMPTE 259M standard for serial digital video (SDV) transmission over coaxial cable. One common application is in SDV routers, which provide a switching matrix for connecting video source equipment (e.g., cameras) to destination equipment (e.g., video tape recorders, monitors, etc.). Figure 12 shows a typical configuration for an SDV router, including equalizers, a crosspoint switch, data retimers, and cable drivers. The CLC014 is used in its standard configuration in this application, and automatically equalizes cable lengths from zero meters to greater than 300 meters at 360 MHz (see plots in Typical Performance Characteristics section). The equalized outputs are connected to the differential inputs of the crosspoint switch. The CLC016 Data Retimer receives the data from the crosspoint and performs the clock and data recovery functions, further reducing jitter. Finally, the retimed data is driven into the coaxial cable by a CLC006 Cable Driver (with two amplitude-adjustable outputs) or a CLC007 Cable Driver (with four outputs). 10005632 FIGURE 12. Video Routing Block Diagram TWISTED PAIR DRIVER A low-cost medium for transmitting data is twisted pair. Category 5 UTP has an attenuation characteristic similar to Belden 8281 coaxial cable but scaled in length: 120 meters of Category 5 UTP is roughly equivalent to 300 meters of Belden 8281 cable. When properly implemented, the CLC014 will equalize data rates up to 625 Mbps over Category 5 UTP. The maximum data rate depends upon the cable length. A plot of Maximum Data Rate vs Cable Length is found in the Typical Performance Characteristics section for Belden 8281, and can be scaled as stated above to estimate maximum cable lengths and data rates for UTP. Category 5 UTP has a characteristic impedance of approximately 100. The CLC006 in Figure 13 is used to drive the twisted pair AC-coupled with a series 0.1 F capacitor and a 50 resistor in each differential output. The CLC014 Adaptive Equalizer requires 800 mVpp from the transmit side of the ca13 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 www.national.com CLC014 ble. A voltage divider is necessary to scale the voltage to the required level at the input of the CLC014. This resistor network also provides the correct impedance match for twisted pair. For Category 5 UTP, the approximate AEC voltage per length is 3.75 mV/m (see Block Description). The CLC006 provides a trim adjust for fine tuning the output signal with the resistor R. Refer to the CLC006/007 datasheet for tuning directions. 10005633 FIGURE 13. Twisted Pair Equalization 10005634 FIGURE 14. Before and After Equalization at 622 Mbps Through 50 Meters of Category 5 UTP 10005635 FIGURE 15. Typical Measurement Setup www.national.com 14 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 Evaluation boards are available for a nominal charge that demonstrate the basic operation of the SDI/SDV/SDH devices. The evaluation boards can be ordered through National's Distributors. Supplies are limited, please check for current availability. The SD014EVK evaluation kit for the CLC014, Adaptive Cable Equalizer for High-Speed Data Recovery, provides an operating environment in which the cable equalizer can be evaluated by system / hardware designers. The evaluation board has all the needed circuitry and connectors for easy connection and checkout of the device circuit options as discussed in the CLC014 datasheet. A schematic, parts list and pictorial drawing are provided with the board. From the WWW, the following information may be viewed / downloaded for most evaluation boards: www.national.com/ appinfo/interface * View a picture of the EVK View the EVK Schematic View the top assembly drawing and BOM View the bottom assembly drawing and BOM PCB LAYOUT The CLC014 requires proper high-speed layout techniques to obtain best results. A few recommended layout rules to follow for best results when using the CLC014 Adaptive Cable Equalizer are: 1. Use a ground plane. 2. Decouple power pins with 0.01 F capacitors placed 0.1" (3mm) from the power pins. 3. Design transmission lines to the inputs and outputs. 4. Route outputs away from inputs. 5. Remove ground plane 0.025" (0.06mm) from the input and output pads. Device Datasheet and / or EVK User Manual 15 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 www.national.com CLC014 * * * * Evaluation Board CLC014 Physical Dimensions inches (millimeters) unless otherwise noted 14-Pin SOIC Order Number CLC014AJE NS Package Number M14A www.national.com 16 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 CLC014 Notes 17 100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25 www.national.com CLC014 Adaptive Cable Equalizer for High-Speed Data Recovery Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2010 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com www.national.com Tel: 1-800-272-9959 National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com 100056 Version 11 Revision 6 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com Print Date/Time: 2010/08/23 16:48:25 National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated