41 12/00
Extremely small dimensions
Versions with special dimensions
can be supplied at short notice
Construction
■Dielectric: polyethylene terephthalate
(polyester)
■Stacked-film technology
■Uncoated
Features
■Special dimensions available upon request
■High pulse strength
■Minimum tensile strength of leads >10 N
Typical applications
■Standard applications
■Electronic lamp ballast circuits
■Energy-saving lamps
■Substitute for electrolytics in electronic
lamp ballasts (420 Vdc)
Terminals
■Parallel wire leads, tinned
■Also available with (3,2 ± 0,3) mm
lead length upon request
■Taped version of B32560 are also
available with lead spacing 5 mm
(leads bent from 7,5 spacing to 5 mm)
Marking
Rated capacitance (coded),
rated dc voltage
Delivery mode
Bulk (untaped)
Taped (AMMO pack or reel) for
lead spacing ≤ 15,0 mm.
For notes on taping, refer to chapter “Taping and packing”, page 274.
Notes on mounting
When mounting these capacitors, take into account creepage distances and clearances to adjacent
live parts. The insulating strength of the cut surfaces to other live parts of the circuit is 1,5 times the
capacitors rated dc voltage, but is always at least 300 Vdc.
Capacitors with 7,5 mm lead spacing are only suitable for use with single-clad printed circuit boards.
Dimensions in mm
Lead spacing
± 0,4
Diameter d1Type
7,5 0,5 B 32 560
10,0 0,5 B 32 561
15,0 0,6 B 32 562
22,5 0,8 B 32 563
27,5 0,8 B 32 564
KMK0687-U
b
Cut
surfaces
h
5-1
ø1
ed
B32560Metallized Polyester Film Capacitors (MKT)
…B32564Uncoated (SilverCaps)
42 12/00
MKT
Overview of available types
Lead
spacing
7,5 mm 10 mm 15 mm 22,5 mm 27,5 mm
Type B 32 560 B 32 561 B 32 562 B 32 563 B 32 564
Page 43 45 46 47 48
1,0 nF
400 Vdc
630 Vdc
1,5 nF
2,2 nF
3,3 nF
4,7 nF
6,8 nF
10 nF
400 Vdc
15 nF
22 nF
33 nF
250 Vdc
47 nF
250 Vdc
400 Vdc
68 nF
0,10 µF
100 Vdc
630 Vdc
0,15 µF
0,22 µF
63 Vdc
250 Vdc
0,33 µF
100 Vdc
400 Vdc
0,47 µF
0,68 µF
250 Vdc
1,0 µF
100 Vdc
250 Vdc
400 Vdc
1,5 µF
2,2 µF
3,3 µF
100 Vdc
4,7 µF
100 Vdc
420 Vdc
5,6 µF1)
6,8 µF
10 µF
15 µF
22 µF
33 µF
1) For B 32 564, 420 Vdc only
B 32 564
B 32 560 …
43 12/00
MKT
Ordering codes and packing units, lead spacing 7,5 mm
VR
(Vrms,
f ≤ 60 Hz)
CRMaximum
dimensions
b × h × l (mm)
Ordering code1) Packing units (pcs)
Ammo
pack
Reel Untaped
63 Vdc
(40 Vac)
0,22 µF 2,5 × 5,2 × 9,0 B32560-J224-+ 2) 2) 2500
0,33 µF 2,5 × 5,6 × 9,0 B32560-J334-+ 2) 2) 2500
0,47 µF 2,6 × 5,8 × 9,0 B32560-J474-+*** 3250 2600 2000
0,68 µF 3,2 × 6,2 × 9,0 B32560-J684-+*** 2850 2300 1500
1,0 µF 4,0 × 6,8 × 9,0 B32560-J105-+*** 2200 1800 1000
1,5 µF 5,1 × 7,6 × 9,0 B32560-J155-+*** 1700 1400 500
2,2 µF 6,5 × 8,2 × 9,0 B32560-J225-+*** 1300 1100 500
3,3 µF 8,5 × 9,1 × 9,0 B32560-J335-+ – – 350
4,7 µF 9,8 × 11,0 × 9,0 B32560-J475-+ – – 250
6,8 µF 11,5 × 13,3 × 9,0 B32560-J685-+ – – 150
100 Vdc
(63 Vac)
0,10 µF 2,5 × 4,7 × 9,0 B32560-J1104-+ 2) 2) 3000
0,15 µF 2,5 × 4,7 × 9,0 B32560-J1154-+ 2) 2) 3000
0,22 µF 2,5 × 5,1 × 9,0 B32560-J1224-+*** 3400 2700 2000
0,33 µF 2,7 × 5,7 × 9,0 B32560-J1334-+*** 3100 2500 1500
0,47 µF 3,4 × 6,1 × 9,0 B32560-J1474-+*** 2500 2000 1200
0,68 µF 4,2 × 6,5 × 9,0 B32560-J1684-+*** 2000 1600 1000
1,0 µF 5,5 × 7,0 × 9,0 B32560-J1105-+*** 1600 1300 500
1,5 µF 6,7 × 8,2 × 9,0 B32560-J1155-+ – – 400
2,2 µF 8,5 × 9,2 × 9,0 B32560-J1225-+ – – 300
250 Vdc
(160 Vac)
33 nF 2,5 × 4,8 × 9,0 B32560-J3333-+ 2) 2) 3000
47 nF 2,5 × 5,2 × 9,0 B32560-J3473-+*** 3500 2800 2300
68 nF 2,6 × 5,7 × 9,0 B32560-J3683-+*** 3400 2700 1700
0,10 µF 3,2 × 6,1 × 9,0 B32560-J3104-+*** 2650 2200 1200
0,15 µF 3,9 × 7,0 × 9,0 B32560-J3154-+*** 2150 1800 1000
0,22 µF 4,9 × 7,5 × 9,0 B32560-J3224-+*** 1750 1400 650
0,33 µF 6,4 × 8,2 × 9,0 B32560-J3334-+ – – 500
1) + Code letter for capacitance tolerance
*** Code number for packing: Ammo pack = 289, reel = 189
Lead spacing changed from 7,5 to 5 mm by bending leads: Ammo pack = 259, reel = 159
The ordering code for untaped components ends after the tolerance code letter.
2) Taping upon request
Capacitance tolerance: ±20 % =ˆ M, ±10 % =ˆ K, ±5 % =ˆ J
Special dimensions available upon request.
For corresponding design rules, refer to chapter “General technical information”, page 290.
B32560
7,5
44 12/00
MKT
Capacitance tolerance: ±20 % =ˆ M, ±10 % =ˆ K, ±5 % =ˆ J
Special dimensions available upon request.
For corresponding design rules, refer to chapter “General technical information”, page 290.
400 Vdc
(200 Vac)
1,0 nF 2,5 × 5,5 × 9,0 B32560-J6102-+ 2) 2) 2300
1,5 nF 2,5 × 5,5 × 9,0 B32560-J6152-+*** 3500 2900 2000
2,2 nF 2,5 × 5,5 × 9,0 B32560-J6222-+*** 3700 3000 2100
3,3 nF 2,5 × 5,5 × 9,0 B32560-J6332-+*** 3400 2800 2000
4,7 nF 2,5 × 5,5 × 9,0 B32560-J6472-+*** 3700 3000 2000
6,8 nF 2,5 × 5,5 × 9,0 B32560-J6682-+*** 3700 3000 2000
10 nF 2,5 × 5,5 × 9,0 B32560-J6103-+*** 3500 2800 2200
15 nF 2,5 × 5,5 × 9,0 B32560-J6153-+*** 3500 2800 2500
22 nF 2,5 × 5,5 × 9,0 B32560-J6223-+*** 3400 2700 2300
33 nF 2,6 × 6,0 × 9,0 B32560-J6333-+*** 3400 2700 1600
47 nF 3,2 × 6,5 × 9,0 B32560-J6473-+*** 2650 2200 1200
68 nF 3,8 × 7,3 × 9,0 B32560-J6683-+*** 2250 1900 1000
0,10 µF4,9 × 7,7 × 9,0 B32560-J6104-+*** 1750 1400 500
0,15 µF6,5 × 8,2 × 9,0 B32560-J6154-+ – – 500
630 Vdc
(400 Vac)
1,0 nF 2,5 × 5,5 × 9,0 B32560-J8102-+ 2) 2) 2300
1,5 nF 2,5 × 5,5 × 9,0 B32560-J8152-+*** 3500 2900 2000
2,2 nF 2,5 × 5,5 × 9,0 B32560-J8222-+*** 3700 3000 2100
3,3 nF 2,5 × 5,5 × 9,0 B32560-J8332-+*** 3400 2800 2000
4,7 nF 2,5 × 5,5 × 9,0 B32560-J8472-+*** 3400 2700 1800
6,8 nF 3,2 × 6,5 × 9,0 B32560-J8682-+*** 2900 2400 1300
10 nF 3,8 × 7,5 × 9,0 B32560-J8103-+*** 2400 2000 1000
Ordering codes and packing units, lead spacing 7,5 mm
VR
(Vrms,
f ≤ 60 Hz)
CRMaximum
dimensions
b × h × l (mm)
Ordering code1) Packing units (pcs)
Ammo
pack
Reel Untaped
1) + Code letter for capacitance tolerance
*** Code number for packing: Ammo pack = 289, reel = 189
Lead spacing changed from 7,5 to 5 mm by bending leads: Ammo pack = 259, reel = 159
The ordering code for untaped components ends after the tolerance code letter.
2) Taping upon request
B32560
7,5
45 12/00
MKT
Capacitance tolerance: ±20 % =ˆ M, ±10 % =ˆ K, ±5 % =ˆ J
Special dimensions available upon request.
For corresponding design rules, refer to chapter “General technical information”, page 290.
Ordering codes and packing units, lead spacing 10 mm
VR
(Vrms,
f ≤ 60 Hz)
CRMaximum
dimensions
b × h × l (mm)
Ordering code1) Packing units (pcs)
Ammo
pack
Reel Untaped
100 Vdc
(63 Vac)
0,33 µF2,5 × 5,2 × 11,5 B32561-J1334-+*** 1750 2400 1600
0,47 µF2,9 × 5,8 × 11,5 B32561-J1474-+*** 1560 2300 1200
0,68 µF3,6 × 6,3 × 11,5 B32561-J1684-+*** 1260 2000 1000
1,0 µF4,5 × 6,9 × 11,5 B32561-J1105-+*** 1050 1500 500
1,5 µF5,6 × 7,8 × 11,5 B32561-J1155-+*** 810 1200 500
2,2 µF6,9 × 9,0 × 11,5 B32561-J1225-+ – – 400
250 Vdc
(160 Vac)
47 nF 2,5 × 4,4 × 11,5 B32561-J3473-+ 2) 2) 2300
68 nF 2,5 × 4,8 × 11,5 B32561-J3683-+*** 1760 2400 1800
0,10 µF2,8 × 5,3 × 11,5 B32561-J3104-+*** 1600 2300 1300
0,15 µF3,3 × 6,0 × 11,5 B32561-J3154-+*** 1300 2000 1000
0,22 µF4,2 × 6,6 × 11,5 B32561-J3224-+*** 1040 1600 700
0,33 µF5,2 × 7,5 × 11,5 B32561-J3334-+*** 850 1300 500
0,47 µF6,3 × 8,5 × 11,5 B32561-J3474-+*** 700 1000 400
400 Vdc
(200 Vac)
10 nF 2,5 × 5,1 × 11,5 B32561-J6103-+*** 1760 2400 1700
15 nF 2,5 × 5,1 × 11,5 B32561-J6153-+*** 1830 2500 2000
22 nF 2,5 × 5,1 × 11,5 B32561-J6223-+*** 1830 2500 2000
33 nF 2,5 × 5,1 × 11,5 B32561-J6333-+*** 1760 2400 1700
47 nF 2,6 × 6,0 × 11,5 B32561-J6473-+*** 1760 2400 1300
68 nF 3,2 × 6,6 × 11,5 B32561-J6683-+*** 1390 2100 1000
0,10 µF4,0 × 6,9 × 11,5 B32561-J6104-+*** 1090 1700 700
0,15 µF5,2 × 7,7 × 11,5 B32561-J6154-+*** 850 1300 500
0,22 µF6,6 × 8,5 × 11,5 B32561-J6224-+ – – 300
1) + Code letter for capacitance tolerance
*** Code number for packing: Ammo pack = 289, reel = 189
The ordering code for untaped components ends after the tolerance code letter.
2) Taping upon request
B32561
10
46 12/00
MKT
Capacitance tolerance: ±20 % =ˆ M, ±10 % =ˆ K, ±5 % =ˆ J
Special dimensions available upon request.
For corresponding design rules, refer to chapter “General technical information”, page 290.
Ordering codes and packing units, lead spacing 15 mm
VR
(Vrms,
f ≤ 60 Hz)
CRMaximum
dimensions
b × h × l (mm)
Ordering code1) Packing units (pcs)
Ammo
pack
Reel Untaped
100 Vdc
(63 Vac)
1,0 µF 3,2 × 6,3 × 16,5 B32562-J1105-+*** 1750 2000 1500
1,5 µF 4,0 × 7,3 × 16,5 B32562-J1155-+*** 1460 1500 1000
2,2 µF 4,9 × 8,0 × 16,5 B32562-J1225-+*** 1190 1300 800
3,3 µF 6,0 × 9,3 × 16,5 B32562-J1335-+*** 960 1000 500
4,7 µF 7,3 × 10,6 × 16,5 B32562-J1475-+*** 790 900 400
6,8 µF 9,0 × 11,8 × 16,5 B32562-J1685-+*** 640 700 290
10 µF 11,8 × 13,0 × 16,5 B32562-J1106-+ – – 200
250 Vdc
(160 Vac)
0,22 µF 3,2 × 5,6 × 16,5 B32562-J3224-+*** 1750 2000 1700
0,33 µF 4,0 × 6,2 × 16,5 B32562-J3334-+*** 1460 1500 1200
0,47 µF 5,0 × 6,7 × 16,5 B32562-J3474-+*** 1190 1300 950
0,68 µF 6,0 × 7,8 × 16,5 B32562-J3684-+*** 960 1000 500
1,0 µF 7,0 × 9,3 × 16,5 B32562-J3105-+*** 830 900 500
1,5 µF 8,7 × 11,0 × 16,5 B32562-J3155-+*** 660 700 300
2,2 µF 10,7 × 12,8 × 16,5 B32562-J3225-+ – – 200
3,3 µF 13,9 × 14,5 × 16,5 B32562-J3335-+ – – 150
400 Vdc
(200 Vac)
47 nF 3,3 × 5,6 × 16,5 B32562-J6473-+*** 1870 2100 1800
68 nF 3,3 × 5,6 × 16,5 B32562-J6683-+*** 1800 2000 1800
0,10 µF 3,3 × 5,6 × 16,5 B32562-J6104-+*** 1700 1900 1600
0,15 µF 3,9 × 6,5 × 16,5 B32562-J6154-+*** 1420 1600 1200
0,22 µF 4,7 × 7,5 × 16,5 B32562-J6224-+*** 1240 1300 850
0,33 µF 6,0 × 8,3 × 16,5 B32562-J6334-+*** 960 1000 500
0,47 µF 7,3 × 9,3 × 16,5 B32562-J6474-+*** 790 900 450
0,68 µF 8,9 × 10,8 × 16,5 B32562-J6684-+*** 640 700 300
1,0 µF 10,9 × 12,5 × 16,5 B32562-J6105-+ – – 200
630 Vdc
(350 Vac)
0,10 µF 6,2 × 9,3 × 16,5 B32562-J8104-+ – – 700
0,15 µF 7,6 × 10,8 × 16,5 B32562-J8154-+ – – 500
0,22 µF 9,2 × 12,2 × 16,5 B32562-J8224-+ – – 350
0,33 µF 11,2 × 14,2 × 16,5 B32562-J8334-+ – – 250
0,47 µF 13,5 × 16,3 × 16,5 B32562-J8474-+ – – 180
1) + Code letter for capacitance tolerance
*** Code number for packing: Ammo pack = 289, reel = 189
The ordering code for untaped components ends after the tolerance code letter.
B32562
15
47 12/00
MKT
Capacitance tolerance: ±20 % =ˆ M, ±10 % =ˆ K, ±5 % =ˆ J
Special dimensions available upon request.
For corresponding design rules, refer to chapter “General technical information”, page 290.
Ordering codes and packing units, lead spacing 22,5 mm
VR
(Vrms,
f ≤ 60 Hz)
CRMaximum
dimensions
b × h × l (mm)
Ordering code1) Packing units (pcs)
Untaped
100 Vdc
(63 Vac)
3,3 µF 5,0 × 8,2 × 24,0 B32563-J1335-+ 1900
4,7 µF 5,9 × 9,0 × 24,0 B32563-J1475-+ 1600
6,8 µF 7,0 × 10,5 × 24,0 B32563-J1685-+ 920
10 µF 8,6 × 12,2 × 24,0 B32563-J1106-+ 960
15 µF 10,9 × 14,0 × 24,0 B32563-J1156-+ 620
22 µF 12,8 × 17,2 × 24,0 B32563-J1226-+ 360
250 Vdc
(160 Vac)
0,68 µF 4,8 × 7,2 × 24,0 B32563-J3684-+ 1760
1,0 µF 5,6 × 8,2 × 24,0 B32563-J3105-+ 1140
1,5 µF 6,9 × 9,5 × 24,0 B32563-J3155-+ 920
2,2 µF 8,3 × 11,2 × 24,0 B32563-J3225-+ 740
3,3 µF 10,1 × 13,5 × 24,0 B32563-J3335-+ 700
4,7 µF 12,2 × 15,5 × 24,0 B32563-J3475-+ 390
400 Vdc
(200Vac)
0,33 µF 5,1 × 8,0 × 24,0 B32563-J6334-+ 1700
0,47 µF 5,7 × 8,3 × 24,0 B32563-J6474-+ 1660
0,68 µF 6,9 × 9,6 × 24,0 B32563-J6684-+ 920
1,0 µF 8,3 × 11,2 × 24,0 B32563-J6105-+ 850
1,5 µF 10,3 × 13,2 × 24,0 B32563-J6155-+ 660
2,2 µF 12,6 × 15,5 × 24,0 B32563-J6225-+ 360
1) + Code letter for capacitance tolerance
B32563
22,5
48 12/00
MKT
Capacitance tolerance: ±20 % =ˆ M, ±10 % =ˆ K, ±5 % =ˆ J
Special dimensions available upon request.
For corresponding design rules, refer to chapter “General technical information”, page 290.
Ordering codes and packing units, lead spacing 27,5 mm
VR
(Vrms ,
f ≤ 60 Hz)
CRMaximum
dimensions
b × h × l (mm)
Ordering code1) Packing units (pcs)
Untaped
100 Vdc
(63Vac)
4,7 µF 5,6 × 8,3 × 29,0 B32564-J1475-+ 1000
6,8 µF 6,3 × 9,5 × 29,0 B32564-J1685-+ 820
10 µF 7,6 × 11,0 × 29,0 B32564-J1106-+ 680
15 µF 9,1 × 13,5 × 29,0 B32564-J1156-+ 430
22 µF 11,0 × 16,0 × 29,0 B32564-J1226-+ 320
33 µF 13,0 × 19,8 × 29,0 B32564-J1336-+ 360
250 Vdc
(160 Vac)
1,0 µF 5,1 × 7,6 × 29,0 B32564-J3105-+ 1620
1,5 µF 5,3 × 10,2 × 29,0 B32564-J3155-+ 970
2,2 µF 6,4 × 11,8 × 29,0 B32564-J3225-+ 920
3,3 µF 7,9 × 14,0 × 29,0 B32564-J3335-+ 750
4,7 µF 9,6 × 15,8 × 29,0 B32564-J3475-+ 400
6,8 µF 11,9 × 18,0 × 29,0 B32564-J3685-+ 300
10 µF 13,8 × 22,5 × 29,0 B32564-J3106-+ 280
400 Vdc
(200 Vac)
1,0 µF 6,8 × 11,2 × 29,0 B32564-J6105-+ 750
1,5 µF 7,8 × 14,2 × 29,0 B32564-J6155-+ 750
2,2 µF 9,6 × 16,4 × 29,0 B32564-J6225-+ 400
3,3 µF 12,2 × 18,8 × 29,0 B32564-J6335-+ 330
4,7 µF 14,2 × 22,8 × 29,0 B32564-J6475-+ 260
420 Vdc
(200 Vac)
4,7 µF 16,0 × 20,0 × 29,0 B32564-T6475-K 290
5,6 µF 16,0 × 20,0 × 29,0 B32564-T6565-K 350
6,8 µF 16,0 × 20,0 × 29,0 B32564-T6685-K 290
1) + Code letter for capacitance tolerance
B32564
27,5
49 12/00
MKT
Technical data
Climatic category
in accordance with IEC 60068-1
55/100/561)
Lower category temperature Tmin
Upper category temperature Tmax
− 55 °C
+ 100 °C (+125 °C for 1000 h and VC = 0,5 ⋅ VR)
Damp heat test 56 days/40 °C/93 % relative humidity
Limit values after damp
heat test1)
Capacitance change |∆C/C|≤ 5 %
Dissipation factor change ∆ tan δ≤ 3 ⋅ 10−3 (at 1 kHz)
≤ 5 ⋅ 10−3 (at 10 kHz)
Insulation resistance Ris ≥ 50 % of minimum
or time constant τ = CR ⋅ Ris as-delivered values
Reliability:
Reference conditions
Failure rate
0,5 ⋅ VR; 40 °C
2 ⋅10−9/h = 2 fit
For a conversion table for other operating conditions and tem-
peratures, refer to chapter “Quality assurance”, page 327.
Service life 200 000 h
Failure criteria:
Total failure
Failure due to variation
of parameters
Short circuit or open circuit
Capacitance change |∆C/C|> 10 %
Dissipation factor tan δ> 2 ⋅ upper limit value
Insulation resistance Ris < 150 MΩ(CR ≤ 0,33 µF)
or time constant τ = CR ⋅ Ris < 50 s (CR > 0,33 µF)
DC test voltage 1,4 ⋅ VR, 2 s
Category voltage VC
Operation with dc voltage or
ac voltage Vrms up to 60 Hz
Operating voltage for
short operating periods
Dissipation factor tan δ (in 10−3)
at 20 °C
(upper limit values)
Insulation resistance Ris
or time constant τ = CR ⋅ Ris
at 20 °C, rel. humidity ≤ 65 %
(minimum as-delivered values)
1) Test criteria must be met after exposure to damp heat for 21 days.
T ≤ 85 °CVC = 1,0 ⋅ VRVC,rms = 1,0 ⋅ Vrms
T ≤ 100 °CVC = 0,8 ⋅ VRVC,rms = 0,8 ⋅ Vrms
T ≤ 85 °C
V
= 1,25 ⋅
V
C, max. 2000 h
V
= 1,0 ⋅
V
C,rms, max. 2000 h
T ≤ 100 °C
V
= 1,25 ⋅
V
C, max. 2000 h
V
= 1,0 ⋅
V
C,rms, max. 2000 h
T ≤ 125 °C
V
= 0,5 ⋅
V
R, max. 1000 h
V
= 0,5 ⋅
V
rms, max. 1000 h
CR ≤ 0,1 µF0,1 µF < CR ≤ 1 µFCR > 1 µF
at 1 kHz 8 8 10
10 kHz 15 15 –
100 kHz 30 – –
VRCR ≤ 0,33 µFCR > 0,33 µF
≤ 100 Vdc 3750 MΩ1250 s
≥ 250 Vdc 7500 MΩ2500 s
… B 32 564
B32560
50 12/00
MKT
Pulse handling capability
Maximum permissible voltage change per unit of time for non-sinusoidal voltages
(pulse, sawtooth).
For Vpp < VR , the permissible voltage rise rate value Vpp/τ may be multiplied by the factor VR/Vpp.
Also refer to the calculation example in chapter “General technical information”, page 302.
Impedance Z
versus
frequency f
(typical values)
VRMax. rate of voltage rise Vpp/τ in V/µs (for Vpp = VR)
Lead spacing
7,5 mm 10 mm 15 mm 22,5 mm 27,5 mm
63 Vdc120––––
100 Vdc 150 75 50 50 25
250 Vdc 200 150 100 100 50
400 Vdc 275 175 125 125 60
420 Vdc ––––60
630 Vdc 320 – 150 – –
VR Pulse characteristic k0 in V2/µs (for Vpp ≤ VR)
Lead spacing
7,5 mm 10 mm 15 mm 22,5 mm 27,5 mm
63 Vdc 15 000––––
100 Vdc 30 000 15 000 10 000 10 000 5 000
250 Vdc 100 000 75 000 50 000 50 000 25 000
400 Vdc 220 000 140 000 100 000 100 000 50 000
420 Vdc ––––50 000
630 Vdc 400 000 – 190 000 – –
Z
KMK0418-A
f
33 µF
F
µ
10
F
µ3,3
F
µ1,0
F
0,33µ
F
µ0,10
Fn33
Fn10
Fn3,3
Fn
1,0
5
Ω
5
5
1
10
0
10
10
10
10
Hz5510
8
10
7
10
65
10
1
_
2
_
3
_
B 32 564
B 32 560 …
51 12/00
MKT
Permissible ac voltage Vrms versus frequency f
Lead spacing 7,5 mm
63 Vdc/ 40 Vac 100 Vdc/ 63 Vac
250Vdc/ 160Vac 400 Vdc/ 200 Vac
KMK0582-H
110 2
f
10 310 410 510 6
Hz555
2
4
6
10
100
60
40
20
200
400
0,22 µF
Vrms
0,68 µF
2,2 µF
6,8 µF
Vac
KMK0583-Q
110
2
f
10
3
10
4
10
5
10
6
Hz555
2
4
6
10
100
60
40
20
200
400
0,1 µF
V
rms
0,33 µF
0,68 µF
1,5 µF
2,2 µF
Vac
Vac
Vrms
Vac
Vrms
B32560
7,5
52 12/00
MKT
Permissible ac voltage Vrms versus frequency f
Lead spacing 7,5 mm
630 Vdc/ 400 Vac
B32560
7,5
53 12/00
MKT
Permissible ac voltage Vrms versus frequency f
Lead spacing 10 mm
100 Vdc/ 63 Vac 250 Vdc/ 160 Vac
400 Vdc/ 200 Vac
Vac
Vrms
Vac
Vrms
Vac
Vrms
10
B32561
54 12/00
MKT
Permissible ac voltage Vrms versus frequency f
Lead spacing 15 mm
100 Vdc/63 Vac 250 Vdc/ 160 Vac
400 Vdc/200 Vac 630 Vdc/350 Vac
Vac
Vrms
Vac
Vrms
KMK0581-9
110
2
f
10
3
10
4
10
5
10
6
Hz555
2
4
6
10
100
60
40
20
200
400
47 nF
V
rms
0,1 µF
0,33 µF
1,0 µF
Vac
Vac
B32562
15
55 12/00
MKT
Permissible ac voltage Vrms versus frequency f
Lead spacing 22,5 mm
100 Vdc/ 63 Vac 250 Vdc/ 160 Vac
400 Vdc/ 200 Vac
KMK0579-X
110
2
f
10
3
10
4
10
5
10
6
Hz555
2
4
6
10
100
60
40
20
200
400
3,3 µF
V
rms
4,7 µF
22 µF
Vac
Vac
Vrms
KMK0580-1
110 2
f
10 310 410 510 6
Hz555
2
4
6
10
100
60
40
20
200
400
0,33 µF
Vrms
0,68 µF
2,2 µF
Vac
B32563
22,5
56 12/00
MKT
Permissible ac voltage Vrms versus frequency f
Lead spacing 27,5 mm
100 Vdc/ 63 Vac 250 Vdc/ 160 Vac
400 Vdc/ 200 Vac
Vac
Vrms
B32564
27,5
1
Herausgegeben von EPCOS AG
Marketing Kommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND
EPCOS AG 2000. Alle Rechte vorbehalten. Vervielfältigung, Veröffentlichung, Verbreitung und
Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG
nicht gestattet.
Mit den Angaben in dieser Broschüre werden die Bauelemente spezifiziert, keine Eigenschaften
zugesichert. Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen
für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird.
Diese Broschüre ersetzt die vorige Ausgabe.
Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgele-
genen Vertrieb der EPCOS AG oder an unsere Vertriebsgesellschaften im Ausland.
Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte
darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsge-
sellschaft einzuholen.
Published by EPCOS AG
Marketing Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY
EPCOS AG 2000. All Rights Reserved. Reproduction, publication and dissemination of this bro-
chure and the information contained therein without EPCOS’ prior express consent is prohibited.
The information contained in this brochure describes the type of component and shall not be con-
sidered as guaranteed characteristics. Purchase orders are subject to the General Conditions for
the Supply of Products and Services of the Electrical and Electronics Industry recommended by the
ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed.
This brochure replaces the previous edition.
For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or
the international Representatives.
Due to technical requirements components may contain dangerous substances. For information on
the type in question please also contact one of our Sales Offices.
